Sony HDCAM HDW-F500 User manual

HD DIGITAL VIDEOCASSETTE RECORDER
HDW-F500
PARALLEL INTERFACE KIT
BKDW-509
HD-SD CONVERTER BOARD
HKDV-501A
HD LINE CONVERTER BOARD
HKDV-502
SDTI BOARD
HKDV-506A
HD PULL DOWN BOARD
HKDV-507D
MAINTENANCE MANUAL Part 1
1st Edition (Revised 3)

HDW-F500E MMP1
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HDW-F500 Serial No. 10101 and Higher
BKDW-509 Serial No. 10001 and Higher
HKDV-501A Serial No. 10001 and Higher
HKDV-502 Serial No. 10001 and Higher
HKDV-506A Serial No. 10001 and Higher
HKDV-507 Serial No. 10001 and Higher
HKDV-507D Serial No. 10001 and Higher

HDW-F500E MMP1
CAUTION
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem
Austausch der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben
des Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé
par le constructeur.
Mettre au rebut les batteries usagées
conformément aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning måkun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.

1
HDW-F500E MMP1
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 5
Related manuals......................................................................................................... 5
Contents ..................................................................................................................... 6
1. Installation
1-1. Operating Conditions ..................................................................................1-1
1-2. Power Supply ..............................................................................................1-1
1-2-1. Power Supply Specifications......................................................1-1
1-2-2. Power Cord.................................................................................1-2
1-3. Connecting Connectors and Cables ............................................................1-3
1-4. Signal Inputs and Outputs of Connector .....................................................1-4
1-5. System Connection Example ....................................................................1-10
1-5-1. Connection with HD Digital Equipment
(When using with 59.94i and 60i modes) ................................1-10
1-5-2. Connection with HD Analog Equipment
(When using with 60i mode)....................................................1-11
1-5-3. Connection with NTSC/PAL Digital Equipment.....................1-12
1-6. Installation of HDW-F500 ........................................................................1-13
1-6-1. Installation Space .....................................................................1-13
1-6-2. Rack Mounting.........................................................................1-14
1-7. Installation of Optional Boards .................................................................1-19
1-7-1. HKDV-502...............................................................................1-19
1-7-2. HKDV-507/507D.....................................................................1-22
1-7-3. HKDV-501A ............................................................................1-25
1-7-4. HKDV-506A ............................................................................1-27
1-7-5. BKDW-509 ..............................................................................1-30
1-8. Switchable Functions ................................................................................1-32
1-8-1. System Frequency Switchable Function ..................................1-32
1-8-2. Line Conversion Switchable Function of
HKDV-502 (Option Board) ...................................................1-34
1-9. Settings of Connector Panel Switches.......................................................1-35
1-10. Settings of Board Switches/Slit Lands and Description of LEDs.............1-35
1-10-1. SS-88 Board .............................................................................1-35
1-10-2. APR-49 Board ..........................................................................1-39
1-10-3. PD-94/107 Board .....................................................................1-48
1-11. Switching of Search Dial Mode ................................................................1-49
1-12. Reference Systems ....................................................................................1-50
1-13. Editor Setup Parameter .............................................................................1-51

2HDW-F500E MMP1
2. Service Overview
2-1. Notes on Power Supply Block ....................................................................2-1
2-1-1. Primary Circuit Block and Warning on Electrical Hazards .......2-1
2-1-2. Resetting the Circuit Breaker .....................................................2-1
2-2. Cleaning Clogged Heads .............................................................................2-1
2-3. Opening/Closing the Lower Control Panel .................................................2-2
2-4. Removing/Installing the Lower Control Panel Assembly ..........................2-2
2-5. Removing/Installing Cabinet ......................................................................2-3
2-5-1. Removing/Installing the Upper Lid, Side Panels, Bottom Plate.. 2-3
2-5-2. Removing/Installing the Upper/Lower Control Panels ..............2-4
2-5-3. Removing/Installing the Connector Panel Assembly ................2-5
2-5-4. Removing/Installing the Power Supply Panel Assembly...........2-6
2-6. Removing/Installing the Plate MD Assembly.............................................2-7
2-7. Removing/Installing the Cassette Compartment.........................................2-8
2-8. Circuit Structure ..........................................................................................2-9
2-9. Location of Main Parts ..............................................................................2-11
2-9-1. Location of Printed Circuit Board/ Switching Regulator .........2-11
2-9-2. Location of Major Mechanical Parts ........................................2-14
2-9-3. Location and Function of Sensors ............................................2-15
2-10. Replacing the Plug-in Board .....................................................................2-17
2-10-1. Removing/Installing the Plug-in Board ...................................2-17
2-10-2. Point to Notice When Replacing the SS-88 Board ..................2-17
2-11. Mechanism of Cassettes ............................................................................2-18
2-12. Removing the Cassette Tape When Tape Slack Occurs ...........................2-20
2-13. Fixtures and Measuring Equipments.........................................................2-21
2-13-1. Fixtures.....................................................................................2-21
2-13-2. Measuring Equipments.............................................................2-25
2-13-3. Alignment Tape ........................................................................2-26
2-14. ISR.............................................................................................................2-28
2-14-1. Outline ......................................................................................2-28
2-14-2. Information on Communicating Cables ...................................2-29
3. Self-Diagnosis
3-1. Overview .....................................................................................................3-1
3-2. Error Messages ............................................................................................3-1
3-3. Warning Messages ....................................................................................3-23
3-4. Channel Condition Messages ....................................................................3-24
3-5. Error Logger Function...............................................................................3-24

3
HDW-F500E MMP1
4. Maintenance Mode
4-1. Maintenance Mode......................................................................................4-1
4-1-1. Overview ....................................................................................4-1
4-1-2. Description of Keys....................................................................4-2
4-1-3. Start-up/Exit of Maintenance Mode...........................................4-2
4-2. Maintenance Information Display...............................................................4-3
4-2-1. ROM VERSION/SERIAL No. ..................................................4-4
4-2-2. Error Logger...............................................................................4-5
4-2-3. Warning Messages .....................................................................4-8
4-2-4. Error Messages...........................................................................4-9
4-2-5. Channel Condition Messages ...................................................4-10
4-2-6. Option Information...................................................................4-10
4-3. Maintenance Menu....................................................................................4-11
4-3-1. PANEL MAINTENANCE Menu ([F3] : PANEL MAINT) ..4-12
4-3-2. SERVO SYSTEM Check ([F4] : SERVO CHECK) ..............4-16
4-3-3. DT/SAT SYSTEM Check ([F5] : DT/SAT CHECK).............4-34
4-3-4. RF SYSTEM Check ([F7] : RF CHECK) ...............................4-39
4-3-5. AUDIO/VIDEO SYSTEM Check ([F8] : A/V CHECK).......4-40
4-3-6. OTHERS Check ([F9] : OTHERS CHECK) ..........................4-46
4-4. Alternative Maintenance Menu.................................................................4-52
4-4-1. SERVO SYSTEM Adjustment ([F4] : SERVO ADJ) ............4-53
4-4-2. DT SYSTEM Adjustment ([F5] : DT ADJ) ...........................4-64
4-4-3. RF SYSTEM Adjustment ([F7] : RF ADJUST) .....................4-69
5. Periodic Maintenance and Inspection
5-1. Periodic Inspection......................................................................................5-1
5-1-1. Index...........................................................................................5-1
5-1-2. Periodic Replacement List .........................................................5-2
5-1-3. Hours Meter ...............................................................................5-4
5-2. Cleaning ......................................................................................................5-6
5-2-1. Cleaning by Cleaning Cloth .......................................................5-6
5-2-2. Cleaning by Cleaning Cassette Tape..........................................5-6
5-2-3. Cleaning the Rotary Heads.........................................................5-7
5-2-4. Cleaning the Tape Running Surface of Upper Drum.................5-8
5-2-5. Cleaning the Tape Running Surface of Lower Drum
and Lead Surface .....................................................................5-9
5-2-6. Cleaning the Stationary Heads .................................................5-10
5-2-7. Cleaning the Tape Running System and Tape Cleaner............5-11
5-2-8. Cleaning the Cassette Compartment and Cassette Supports....5-12
5-2-9. Cleaning the Fan Motors ..........................................................5-13

4HDW-F500E MMP1
6. Spare Parts ............................................................................................. 6-1
7. Overall Block Diagram
7-1. Signal Processing System ...........................................................................7-2
7-2. Control System ............................................................................................7-6

5
HDW-F500E MMP1
Manual Structure
Purpose of this manual This manual is the maintenance manual part 1 of the HD digital video cassette
recorder HDW-F500.
This manual is intended for use by trained system and service engineers, and is
provided information required for the installation, maintenance information and
information for service such as replacement of plug-in boards.
And this manual is provided the related information (such as installation.) for the
following optional boards.
BKDW-509 Paralle Interace Kit
HKDV-501A HD-SD Converter Board
HKDV-502 HD Line Converter Board
HKDV-506A SDTI Board
HKDV-507/507D HD Pull Down Board
Related manuals Besides this maintenance manual part 1, the following manuals are available.
..
..
.Operation Manual (Supplied with this unit)
This manual is necessary for the use and operation (and installation) of this unit.
Part No.: 3-203-128-XX
..
..
.Maintenance Manual Part 2 (Available on your request)
This manual is provided information that is premised the parts level service
(adjustments, board layouts, schematic diagrams, detailed parts list and the like.)
for this unit and optional board. If this manual is required, please contact to your
local Sony Sales Office/Service Center.
Volume 1 (Service Information , Replacement of Parts and Adjustments)
Part No.: 9-968-552-XX
Volume 2 (Schematic Diagrams, Board Layouts, Block Diagrams, Exploded View
and Parts Lists).
Part No.: 9-968-553-XX
..
..
.Protocol Manual for Remote (9-pin) (Available on your request)
This manual is explained the protocols for controlling this unit by the RS-422A
(9-pin serial remote). If this manual is required, please contact to your local Sony
Sales Office/Service Center.
Part No.: 9-968-513-XX
..
..
.BKDW-509 Interface Manual (Available on request)
This manual is explained the protocols for controlling this unit by the parallel 50-
pin. If this manual is required, please contact to your local Sony Sales Office/
Service Center.
Part No.: 9-967-559-XX

6HDW-F500E MMP1
..
..
.ISR Protocol Manual (Available on your request)
This manual is explained the ISR functions (Interactive Status Reporting/Integrat-
ed Equipment Management Function) of the this unit. If this manual is required,
please contact to your local Sony Sales Office/Service Center.
ISR:Interactive Status Reporting/Integrated Equipment Management Function
Part No.: 9-968-521-XX
..
..
.“Semiconductor Pin Assignments” CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
service manual for the corresponding unit. The service manual contains a com-
plete list of all semiconductors and their ID Nos., and thus should be used together
with the CD-ROM.
Part number: 9-968-546-XX
Contents The maintenance manual part 1 is organized by following sections.
Section 1 Installation
This section is described about the information that is required to install (operating
conditions, installation space, connection information, initial setting and the like.)
and when installing this unit and optional board to this unit.
Section 2 Service Overview
This section is described about fundamental information that is required for service
(removing of cabinet and cassette compartment, location of printed circuit board and
main parts, fixture and measuring equipments cautions and the like.), measures
against trouble and ISR (Interactive Status Reporting).
Section 3 Self Diagnosis
This section is described about error messages and error logger.
Section 4 Maintenance Mode
This section is described about each menu of the maintenance mode.
Section 5 Periodic Maintenance and Inspection
This section is described about the recommended periodic maintenance and cleaning
procedures.
Section 6 Spare Parts
This section is described about the repair parts list for the service parts of this unit,
packing materials and supplied accessories list, and optional parts list.
Section 7 Overall Block Diagram
This section is described about overall block diagram.

1-1
HDW-F500E MMP1
Section 1
Installation
1-1. Operating Conditions
n
To prevent internal heat build-up, do not block the ventila-
tion holes on the cabinet and the air vents of the fan.
Operating temperature:
+5 dC to +40 dC
Operating humidity:
25% to 80% (Condensation no allowed)
Storage temperature:
_20 dC to +60 dC
Locations to avoid:
.Areas where the unit will be exposed to direct
sunlight or any other strong lights.
.Areas near heat sources.
.Dusty areas or areas subject to vibration.
.Areas with strong magnetic field.
.Areas with considerable electric noise.
.Areas where static electricity occur easily.
.Areas without the required installation space.
(Refer to “1-6-1. Installation Space”.)
Horizontal condition:
Do not tilt the front and rear of the unit by more
than 30d.
c
When using the unit where it is not horizon-
tal, fix the unit properly so that it does not
slip.
1-2. Power Supply
1-2-1. Power Supply Specifications
w
Be sure to operate the unit within the range of the
following recommended power supply voltage.
Recommended power supply voltage:
AC 100 to 240 V ±10%
Recommended power frequency:
50 Hz or 60 Hz
Power consumption:
230 W
Rush current:
Power supply voltage 100 V: 10 A
Power supply voltage 240 V: 20 A
This unit uses a switching regulator.
n
The AC power supply requires a capacity commensurate
with the rush current.
If the AC power supply capacity is insufficient, the breaker
of the AC power supply at the supply side may operate or
this unit may not operate normally.

1-2 HDW-F500E MMP1
AC inlet
2
1
For the customer in the U.S.A. and Canada
Required Parts
1Power Cord, 125 V 10 A (2.4 m) : 1-551-812-11
2Plug Holder B (Black) : 2-990-242-01
2
AC inlet
1
For the customer in the United Kingdom
Required Parts
1Power Cord, 250 V 10 A (2.4 m) : 1-782-165-11
2Plug Holder C (Brown) : 3-613-640-01
AC inlet
2
1
For the customer in the all European countries
except the United Kingdom
Required Parts
1Power Cord, 250 V 10 A (2.0 m) : 1-551-631-22
2Plug Holder C (Brown) : 3-613-640-01
1-2-2. Power Cord
w
The power cords are not supplied with the unit. Be sure to
use power cords that are suitable for the place of operation.
n
For the customer outside of the area as shown above, please
contact your local Sony Sales Office/Service Center.
1-2. Power Supply

1-3
HDW-F500E MMP1
1-3. Connecting Connectors and Cables
When connecting cables to connectors of this unit, use the following connectors or cables (or equiva-
lents).
HDW-F500 Side Connector/Panel Indication Matching Connector/Cable Sony Part No.
ANALOG I/O BNC 75 Z, Male –
REF. IN
REF. OUT
D CONV. OUT BNC 75 Z, Male –
(When HKDV-501A is installed)
DIGITAL I/O BNC 75 Z, Male –
AUDIO INPUT (AES/EBU)
AUDIO OUTPUT (AES/EBU)
DIGITAL I/O BNC 75 Z, Male(*1) –
HD SDI INPUT
HD SDI OUTPUT
PULL DOWN OUT (When HKDV-507/507D is installed)
DIGITAL I/O BNC 75 Z, Male(*2) –
D CONV. SDI (D1/D2) OUTPUT
(When HKDV-501A is installed)
ANALOG I/O XLR 3-pin, Male 1-508-084-00
AUDIO INPUT
TIME CODE IN
ANALOG I/O XLR 3-pin, Female 1-508-083-00
AUDIO OUTPUT
TIME CODE OUT
AUDIO MONITOR R
AUDIO MONITOR L
REMOTE1-IN (9P) 9-pin remote control cable(*4) 1-751-019-81
REMOTE1-OUT (9P)
VIDEO CONTROL D-sub 9-pin, Male 1-563-815-21
Junction shell 9-pin 1-561-749-00
CONTROL PANEL D-sub 15-pin, Male 1-561-610-21
Junction shell 15-pin 1-561-929-00
RS232C D-sub 25-pin, Male 1-566-356-11
PARALLEL I/O (50P) D-sub 50-pin, Male 1-556-358-11
PHONE(*3) JM-60 stereo phone plug –
(*1): Max. cable length: 100 m
However it is recommended that the 5C-FB Fujikura Densen coaxial cable or equivalent be used.
(*2): Max. cable length: 200 m
However it is recommended that the 5C-2V Fujikura Densen coaxial cable or equivalent be used.
(*3): On the front (upper control panel).
(*4): Supplied with the HDW-F500.
1-3. Connecting Connectors and Cables

1-4 HDW-F500E MMP1
1-4. Signal Inputs and Outputs of Connector
Communication connectors
8CONTROL PANEL D-SUB 15P connector
8REMOTE 1 IN D-SUB 9P connector
8REMOTE 1 OUT D-SUB 9P connector
8RS232C D-SUB 25P connector
8VIDEO CONTROL D-SUB 9P connector
(When installing the optional HKDV-503 digital video controller)
9REMOTE PARALLEL I/O D-SUB 50P connector
(When installing the optional board BKDW-509)
Input connectors
1REF HD BNC x2 (loop through connection)
Ternary SYNC
0.6 Vp-p, 75 Z
1REF SD BNC x2 (loop through connection)
Black burst
0.286 Vp-p, 75 Z, sync negative
2DIGITAL AUDIO (AES/EBU) BNC x2
CH1/2, CH3/4 AES/EBU format stereo mode, unbalanced
2DIGITAL HD SDI BNC x1 (1; With Input monitor output)
HD serial digital (1.485 Gbps)
BTA S-004A
2SDTI (OPTION) BNC x1
(When installing the optional board HKDV-506A) SDTI (270 Mbps)
SMPTE 305M
3ANALOG AUDIO XLR3 pin x5
CH1/2/3/4/CUE LOW OFF: _60 dBu, high impedance, balanced
HIGH OFF: +4 dBu, high impedance, balanced
HIGH ON: +4 dBm, terminated at 600 Z, balanced
4TIME CODE IN XLR3 pin x1
0.5 to 18 Vp-p, 10 kΩ, balanced
1-4. Signal Inputs and Outputs of Connector
12
3
4
5
6
7
<Reduced Drawing of Rear Panel>
8
9

1-5
HDW-F500E MMP1
1-4. Signal Inputs and Outputs of Connector
Output connectors
1REF 1125 SYNC BNC x2
0.6 Vp-p, 75 Z
1D CONV. SYNC BNC x1
(When installing the optional board HKDV-501A) 0.286 Vp-p, 75 Z, sync negative
1D CONV. COMPOSITE (SUPER) BNC x1
(When installing the optional board HKDV-501A) 1.0 Vp-p, 75 Z, sync negative
2DIGITAL AUDIO (AES/EBU) BNC x2
CH1/2, CH3/4 AES/EBU format stereo mode, unbalanced
2SDTI (OPTION) BNC x1
(When installing the optional board HKDV-506A) SDTI (270 Mbps)
SMPTE 305M
2DIGITAL HD SDI BNC x1 (including 1 for character superimpose)
1/2/3/MONITOR Serial digital (1.485 Gbps)
BTA S-004A
3ANALOG AUDIO XLR3 pin x5
CH1/2/3/4/CUE +4 dBm (600 Zload), balanced
4TIME CODE OUT XLR3 pin x1
2.2 Vp-p, low impedance, balanced
5AUDIO MONITOR R/L XLR3 pin x2
+4 dBm (600 Zload), balanced
6PULL DOWN OUT (OPTION) BNC x2 (including charactor superimpose)
MONITOR 1/2 Serial digital (1.485 Gbps)
(When installing the optional board HKDV-507/507D) BTAS-004A
7D CONV. SDI (OPTION) BNC x3 (including 1 for character superimpose)
1/2/3 (SUPER) Serial digital (270 Mbps or 143 Mbps)
(When installing the optional board HKDV-501A) SMPTE259M/CCIR656-3
HEADPHONES JM-60 stereo phone jack
(Upper control panel) Up to _12 dBu (8 Zload), unbalanced
ANALOG I/O DIGITAL I/O
75Ω
ON
OFF
75Ω
ON
OFF
HD SD
REF. IN REF. OUT
1125 SYNC
SYNC
D CONV. OUT(OPTION)
COMPOSITE
(SUPER)
SDTI (OPTION)
AUDIO OUTPUT (AES/EBU)
CH1/2
CH3/4
AUDIO INPUT (AES/EBU)
CH1/2 CH3/4
HD SDI INPUT
HD SDI OUTPUT
INPUT MONITOR
1
3
2
MONITOR
PULL DOWN OUT TIME CODE
IN OUT
IN OUT
CUELEVEL
LOW
OFF
HIGH
ON
600Ω
CH4LEVEL
LOW
OFF
HIGH
ON
600Ω
CH3LEVEL
LOW
OFF
HIGH
ON
600Ω
CH2LEVEL
LOW
OFF
HIGH
ON
600Ω
CH1LEVEL
LOW
OFF
HIGH
ON
600Ω
AUDIO INPUT
AUDIO OUTPUT CUECH4CH3CH2CH1
CONTROL PANEL REMOTE1-IN (9P)RS232C VIDEO CONTROLREMOTE1-OUT (9P)
PARALLEL I/O (50P)
REMOTE
RL
MONITOR OUTPUT
D CONV. SDI OUT
(OPTION)
12
12
3 (SUPER)
MONITOR
< Rear Panel >
BREAKER AC IN
(OPTION)

1-6 HDW-F500E MMP1
CONTROL PANEL: 15-pin (Female)
<External View>
CONTROL PANEL
Pin No. Signal Name
1 KEY RX (_)
2 KEY RX (+)
3NC
4 REG +8 V
5 REG +8 V
6 REG +8 V
7 REG +8 V (2)
8NC
9 GND
10 KEY TX (+)
11 NC
12 KEY TX (+)
13 GND
14 GND
15 GND
1-4. Signal Inputs and Outputs of Connector
81
915

1-7
HDW-F500E MMP1
REMOTE-1 IN/OUT: 9-pin (Female)
<External View>
REMOTE 1-IN REMOTE 1-OUT
REMOTE 1-IN
Pin No. Signal Name
1 GND
2 RM TX (_)
3 RM RX (+)
4 GND
5 PRIORITY IN
6 GND
7 RM TX (+)
8 RM RX (_)
9 GND
REMOTE 1-OUT
Pin No. Signal Name
1 GND
2 RM TX (_)
3 RM RX (+)
4 GND
5 PRIORITY OUT
6 GND
7 RM TX (+)
8 RM RX (_)
9 GND
n
Pin No. 5
PRIORITY IN: Each unit confirms that there is the next
unit sequentially.
PRIORITY OUT: The last unit which confirmed that there
is no next unit notifies the HDW-F500
that all units have been connected.
RS232C: 25-pin (Female)
<External View>
RS232C
Pin No. Signal Name
1 FG; Frame Ground
2 TXD; Transmitted Data (Output)
3 RXD; Received Data (Input)
4 RTS; Request to Send (Output)
5 CTS; Clear to Send (Input)
6 DSR; Data Set Ready (Input)
7 SG; Signal Ground
8 DCD; Data Carrier Detect (Input)
9NC
10 NC
11 NC
12 NC
13 NC
14 NC
15 NC
16 NC
17 NC
18 NC
19 NC
20 DTR; Data Terminal Ready (Output)
21 NC
22 NC
23 NC
24 NC
25 NC
6
1
5
9
1-4. Signal Inputs and Outputs of Connector
13 1
25 14
6
1
5
9

1-8 HDW-F500E MMP1
VIDEO CONTROL: 9-pin (Male)
<External View>
VIDEO CONTROL
Pin No. Signal Name
1 GND
2 REM TX (_)
3 REM RX (+)
4 GND
5N.C.
6 GND
7 REM TX (+)
8 REM RX (_)
9 GND
1-4. Signal Inputs and Outputs of Connector
9
5
1
6

1-9
HDW-F500E MMP1
REMOTE PARALLEL I/O: 50-pin (Female) Factory Setting
<External View>
REMOTE PARALLEL I/O
Pin No. Signal Name
1 FF IN
2 REC SW OUT
3 PLAY SW OUT
4 STOP SW OUT
5 ENTRY SW OUT
6 REF SYSTEM ALARM OUT
7 CF LOCK OUT
8 DRUM LOCK OUT
9 CAP LOCK OUT
10 CUE PRESET OUT
11 TC PRESET OUT
12 CASSETTE OUT/IN OUT
13 TAPE THICKNESS OUT
14 SPARE
15 SPARE
16 +12 V
17 GND
18 PREROLL IN
19 STBY ON IN
20 REW IN
21 ENTRY IN
22 STBY OFF IN
23 EJECT IN
24 REC OUT
25 CH CONDITION RED OUT
1-4. Signal Inputs and Outputs of Connector
17 1
33 50 34 18
Pin No. Signal Name
26 ASSEMBLE PRESET OUT
27 EDIT OUT
28 EJECT OUT
29 59.94 Hz/60 Hz OUT
30 REEL HUB
31 CURRENT DB CHANG OUT
32 ALL REC INHIBIT
33 GND
34 PLAY IN
35 STOP IN
36 REC IN
37 REV LAMP OUT
38 DA2 PRESET OUT
39 DA1 PRESET OUT
40 FWD LAMP OUT
41 DA4 PRESET OUT
42 DA3 PRESET OUT
43 STOP OUT
44 VIDEO PRESET OUT
45 INSERT PRESET OUT
46 STBY ON OUT
47 PLAY OUT
48 REMOTE OUT
49 ALARM OUT
50 PREROLL OUT

1-10 HDW-F500E MMP1
1-5. System Connection Example
1-5-1. Connection with HD Digital Equipment (When using with 59.94i and 60i modes)
(*1): Astro Design HD-694, etc.
(*2): Canare BCJ-XP-TRA, etc.
(*3): When bridge-connecting the DIGITAL AUDIO signals, set the 75 Ztermination switch to OFF.
When not bridge-connecting, set it to ON.
1-5. System Connection Example
(HD DIGITAL VIDEOCASSETTE RECORDER)
DIGITAL I/O
INPUT
MONITOR HD SDI INPUT HD SDI
OUTPUT
1
2
3
MONITOR
(*3)
AUDIO
INPUT
(AES/EBU)
CH1/2
CH3/4
HDW-F500
75Z
75Z
AUDIO
OUTPUT
(AES/EBU)
CH1/2
CH3/4
HD
SD REF. IN
75Z
75ZD CONV. OUT
(OPTION)
REF. OUT 1125 SYNC
SYNC
COMPOSITE
(SUPER)
ANALOG I/O
600Z
600Z
600Z
600Z
600Z
CH1
CH2
CH3
CH4
CUE
AUDIO
INPUT AUDIO
OUTPUT
CH1
CH2
CH3
CH4
CUE
TIME CODE IN TIME CODE OUT
PULL DOWN OUT
(OPTION)
MONITOR OUTPUT R
L
D CONV. SDI OUT
(OPTION)
1
2
3
(SUPER)
CONTROL PANEL
REMOTE1-IN(9P)
RS232C
REMOTE-OUT(9P)
VIDEO CONTROL
P/S
CONVERTER
XLR BNC
XLR BNC
HDD/HDDP-1000
50-PIN PARALLEL
OUTPUT
DIGITAL AUDIO
OUTPUT
CH1/2
CH3/4
REMOTE(9-PIN)
VIDEO MONITOR
(HD SERIAL MONITOR)
SDI DIGITAL VIDEO
ANALOG VIDEO
AES/EBU DIGITAL AUDIO
ANALOG AUDIO
RS-422A
(*1)
(*2)
(*2)
SDTI IN
(OPTION)
MONITOR1
MONITOR2
SDTI OUT(OPTION)