Sony MSW-A2000 User manual

DIGITAL VODEOCASSETTE RECORDER
MSW-A2000/A2000P
INSTALLATION MANUAL
1st Edition
Serial No. 10001 and Higher: MSW-A2000
Serial No. 40001 and Higher: MSW-A2000P

MSW-A2000
MSW-A2000P
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden.Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.

MSW-A2000
MSW-A2000P
CAUTION
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem
Austausch der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben
des Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé
par le constructeur.
Mettre au rebut les batteries usagées
conformément aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
1 (P)
Voor de klanten in Nederland
Dit apparaat bevat een (CF)n-Li batterij voor memory
back-up.
Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat bij einde
levensduur afdankt.
Gooi de batterij niet weg. maar lever hem in als KCA.
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.

1
MSW-A2000
MSW-A2000P
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 2
Related manuals......................................................................................................... 2
1. Installation
1-1. Installation Procedure..................................................................................1-1
1-2. Supplied Accessories ..................................................................................1-1
1-3. Operating Conditions ..................................................................................1-2
1-4. Power Supply ..............................................................................................1-2
1-4-1. Voltage and Power Requirements ..............................................1-2
1-4-2. Power Cord.................................................................................1-2
1-5. Installation Space ........................................................................................1-3
1-6. Rack Mounting............................................................................................1-4
1-7. Matching Connectors and Cables................................................................1-9
1-8. Signal Inputs and Outputs .........................................................................1-10
1-9. Switch Settings on Connector Panel .........................................................1-14
1-10. Analog Audio-related Switch Settings......................................................1-15
1-11. Displaying Setup Extended Menu.............................................................1-18
1-12. Removing/Reattaching Lower Control Panel Unit ...................................1-19
1-13. Switching Search Dial Mode ....................................................................1-21
1-14. Reference System......................................................................................1-22
1-15. Settings and Adjustment when External Equipment is Connected...........1-23
1-15-1. Settings for Time Code ............................................................1-23
1-15-2. VTR Constant Values Settings of Editor .................................1-23
1-15-3. System Phase Alignment..........................................................1-24
1-15-4. Setup Menu Settings ................................................................1-24
1-16. Removing/Reattaching Plug-in Boards.....................................................1-25

2MSW-A2000
MSW-A2000P
Purpose of this manual This manual is the installation manual of digital videocassette recorder MSW-
A2000/A2000P.
This manual is intended for use by trained system and service engineers, and
provides the information that is required to install (environment, connection infor-
mation, initial setting, etc.) and the setting check sheet.
Related manuals Besides this “installation manual”, the following manuals are available for digital
videocassette recorder MSW-A2000/A2000P.
..
..
.Operation Manual (Supplied with the MSW-A2000/A2000P.)
This manual is necessary for application and operation (and installation) of the MSW.
..
..
.Maintenance Manual (Available on request)
Volume-1 : Service Instruction
Volume-2 : Parts List
Volume-3 : Diagrams
These manuals describe the maintenace and service information (service over-
view, adjustments, board layouts, schematic diagrams, detailed parts list, etc.) for
this unit. If these manuals are required, please contact your local Sony Sales
Office/Service Center.
..
..
.Protocol Manual of Remote (9-pin) Connector (Available on request)
This manual explains the protocol for controlling the VTR via the RS-422A (9-pin
serial remote). If this manual is required, please contact your local Sony Sales
Office/Service Center.
..
..
.Interface Manual of Parallel I/O (50-pin) Connector (Available on
request)
This manual explains the protocol for controlling the VTR via the parallel (50-
pin). If this manual is required, please contact your local Sony Sales Office/
Service Center.
..
..
.“Semiconductor Pin Assignments” CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in the MSW.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual (volume-3) for the corresponding unit. The maintenance
manual (volume-3) contains a complete list of all semiconductors and their ID
Nos., and thus should be used together with the CD-ROM.
Part number: 9-968-546-XX
Manual Structure

1-1
MSW-A2000
MSW-A2000P
1-3. Operating Conditions
1-4. Power Supply
1-5. Installation Space
1-6. Rack Mounting
1-7. Matching Connectors and Cables
1-8. Signal Inputs and Outputs
1-9. Switch Settings on Connector Panel
1-10. Analog Audio-related Switch Settings
1-11. Displaying Setup Extended Menu
1-12. Removing/Reattaching Lower Control Panel Unit
1-13. Switching Search Dial Mode
1-14. Reference System
1-15. Settings and Adjustment when External Equipment is Connected
Start
Determination of
installation place
Unpacking
Rack mounting
*Connection
*Initial setup
*Operation check
End
n
If an error message appears on the time data display area, refer to the operation manual.
(For more details, refer to the maintenance manual volume-1.)
n
When the unit is transported, it is required to pack the unit into the specified new packing materials.
Do not reuse the packing materials.
Section 1
Installation
1-2. Supplied Accessories
Screws for rack mounting (PSW 4 x 16) ..........................4
Operation manual ..............................................................1
Installation manual ............................................................1
1-1. Installation Procedure
Installation procedure of this unit is shown on the follow-
ing flowchart.
Refer to each section about detail of each flow.
The operation manual is also required to do *-marked
flow.

1-2 MSW-A2000
MSW-A2000P
n
AC power supply is required a capacity which is commen-
surate with rush current.
If the capacity of the AC power supply is not enough, the
breaker of AC power of a supply side may operate or this
unit may not operate normally.
1-4-2. Power Cord
w
Use the specified power cord only when connecting the
AC power.
Never use a damaged power cord.
For customers in the U.S.A. and Canada:
1Power cord (approx. 2.4 m) !1-557-377-11
2Plug holder (Brown) 3-613-640-01
Please contact your local Sony Sales Office/Service
Center.
For customers in the United Kingdom:
1Power cord DK-2401(UK) (approx. 2.4 m)
2Plug holder (Brown) 3-613-640-01
Plug holder is included in DK-2401(UK).
For customers in Europe except the United Kingdom:
1Power cord DK-2401(AE) (approx. 2.4 m)
2Plug holder (Brown) 3-613-640-01
Plug holder is included in DK-2401(AE).
If the unit is used in the area except above, please contact
your local Sony Sales Office/Service Center.
1-3. Operating Conditions
1-4. Power Supply
1-3. Operating Conditions
c
Good air circulation is essential to prevent internal heat
build-up. Place the unit in location with sufficient air
circulation.
Do not block the ventilation holes of the cabinet and the
front and rear panels.
Operating temperature: 5 dC to 40 dC
Operating humidity: 25 % to 80 %
(Condensation not allowed)
Storage temperature: _20 dC to 60 dC
Locations to avoid:
.Areas where the unit will be exposed to direct sunlight
of any other strong lights.
.Areas near heat sources.
.Dusty areas or areas subject to vibration.
.Areas with strong magnetic field.
.Areas with much electrical noise.
.Areas with much static electricity.
.Areas that is impossible to find a specified room for
installation.
(Refer to “1-5. Installation Space” page 1-3.)
.Areas windtight.
Tilt allowance: Within 30d
Do not slant the front and rear of the
unit more than 30d.
c
Fix the unit securely to avoid drop when the unit is operat-
ed at not-horizontal place.
1-4. Power Supply
1-4-1. Voltage and Power Requirements
w
Be sure to operate the unit within the range of following
power voltage.
Power voltage: AC 100 to 240 V ±10 %
Power frequency: 50 Hz or 60 Hz
Power consumption: 2A (200 W)
(Without the optional kit.)
Rush current: Power voltage 100 V IN; 10 A
Power voltage 240 V IN; 20 A
This unit’s power line has a switching regulator.
AC inlet
2
1
2
AC inlet
1
AC inlet
2
1

1-3
MSW-A2000
MSW-A2000P
533
12.7
112
8787
17419.5 87
3737
3131
123.8
34 263.5 415.9
416(Rail-installed width)
427(Unit width)
45.5
15.9465
36431.5 427
481 45445105 577(Maximum traveling distance)
Unit : mm
Mass of MSW-A2000/A2000P : 22 kg 544
457.5
48 (38.5)
1-5. Installation Space
Moreover, an air flow that is effective in cooling the unit is
essential. If the ventilation is not enough, the unit may be
damaged because of an increase of the internal tempera-
ture.
n
This unit is air-cooled by the five fans. The operation with
the upper lid is removed affects the air cooling by the fans.
Complete the work in a short time as possible when operat-
ing the unit for inspection with the upper lid removed. If it
takes a long time, blow to the unit by an electric fan to cool
the unit.
1-5. Installation Space
When installing, the installation space must be secured in
consideration of the ventilation and service operation.
.Do not block the ventilation slots at the left side and
right side panels, and vents of the fans.
.Leave a space around the unit for ventilation.
.Leave more than 40 centimeters of space in the rear of
the unit to secure the operation area.
When the unit is installed on the desk or the like, leave at
least four centimeters of space in the left and right sides.
Leaving 40 centimeters or more of space above the unit is
recommended for service operation.
Dimensions when Rack-Mounting
n
The MSW-A2000/A2000P allows the operation with the detached lower control panel unit.
For details, refer to Section 1-12.
nRemove the feet when rack mounting.

1-4 MSW-A2000
MSW-A2000P
1-6. Rack Mounting
1-6. Rack Mounting
Explains how to mount this unit into a 19-inch standard
rack.
Be sure to mount this unit into a rack accurately following
the procedure and notes mentioned below.
c
.Use the specified rack mount rail.
The use of other rail of low strength may drop the unit
and cause the risk of injury.
.To prevent toppling over the rack, fix it on the horizontal
and firm floor securely with bolts, etc.
.Mount the unit into a rack with a steady posture.
m
.When other equipment with built-in hard disk drive is
already mounted in the same rack for mounting this unit,
turn off the power of the equipment before mounting this
unit.
.Connect long enough cables on the connector panel,
considering that the unit is pulled out from the rack.
.Do not operate this unit without the upper lid and bottom
plate except when servicing it.
.Adjust the temperature inside the rack within the range
of the unit’s operating temperature.
(Refer to Section 1-3.)
Specified Rack Mount Kit
RMM-130 (Optional accessory)
n
When mounting this unit into Sony LMS (Library Manage-
ment System) VTR console, it is necessary to modify the
VTR console.
Parts Packed in RMM-130
.Slide rails......................................... 2
.Rack angles (handles) ..................... 2
.Rail brackets.................................... 4
.Plate nuts (large) ............................. 4
.Plate nuts (small)............................. 4
.Screws (PSW4 x 16) ...................... 4
.Screws (B4 x 8) .............................. 8
.Hexagon socket head cap screws .... 8
.Flat washers..................................... 8
.Screws (RK5 x 14) ......................... 2
.Ornamental washers ........................ 2
.L-shaped hexagon wrench .............. 1
Rack Mounting Procedure
.Removing the feet
1. Set the unit its side panel down.
2. Unscrew the four screws to remove the feet from the
bottom plate of the unit.
3. Set the unit in a horizontal position.
n
Keep these screws and the feet.
When operating the unit after demounting it from the rack,
be sure to reattach the feet.
Tightening torque: 98 x10_2N .m {10 kgf .cm}
PS4 x20
Foot
PS4 x20
Foot

1-5
MSW-A2000
MSW-A2000P
Outer rail
Intermediate rail
Inner rail
Stopper
A
B
.Attaching the rack angles (handles)
8. Remove the four screws from both sides (left and
right) of the unit.
n
Keep these screws (B4 x6).
Be sure to use these screws when directly fixing the
side panels without the rack angles.
The use of longer screws such as the screws (PSW 4 x
16) for fixing the rack angles will cause a malfunction
of the unit.
9. Attach the two rack angles to both sides (left and right)
of the unit with the supplied four screws (PSW4 x16).
Tightening torque: 120 x10_2N .m {12.2 kgf .cm}
1-6. Rack Mounting
.Attaching the inner rails
4. Pull out the inner rails from the two intermediate rails.
5. While pressing the stopper of the inner rail in the
direction of the arrow A in the figure, pull the inner
rail out in the direction of the arrow B.
6. Remove the ten screws from both sides (left and right)
of the unit as shown in the figure below.
7. Attach the two inner rails to both sides (left and right)
of unit with the removed screws in the step 6.
Tightening torque: 120 x10_2N .m {12.2 kgf .cm}
n
Be sure to use the (B4 x 6) screws when attaching the
inner rail. The use other-sized screws may cause a
malfunction.
Inner rail
Inner rail
B4 x6
B4 x6
B4 x 6
B4 x 6
B4 x 6
B4 x 6
PSW4 x 16
PSW4 x 16
PSW4 x 16
PSW
4 x 16
Rack angle
Rack angle

1-6 MSW-A2000
MSW-A2000P
Plate nut (small)
Rail bracket
Rail
Flat washer
Hexagon socket
head cap screw
L-shaped hexagon wrench
By 4U
2U
Rack
50 to 55 mm
Outer rail
Rack angle B4 x8
Rail bracket
.Attaching the outer rails
12. Loosely attach the two outer rails to the middle of the
4U space in the rack for mounting this unit, with the
eight hexagon socket head cap screws, eight flat
washers, and four plate nuts (small).
13. As shown in the following figure, adjust each front-
side position of the outer rails on both sides (left and
right) so that the distance from the surface of the rack
to the tip of the rail becomes within the range of 50 to
55 millimeters.
14. Fully tighten the eight screws (B4 x 8) fixing the four
rail brackets.
Tightening torque: 120 x10_2N .m {12.2 kgf .cm}
1-6. Rack Mounting
.Loosely attaching the rail brackets
10. Slide the intermediate rail as shown in the figure, and
then loosely attach the rail bracket to the outer rail
with a plate nut (large) and the two screws.
11. Slide the ball retainer in the direction of the arrow, and
then loosely attach the rail bracket to the outer rail
with a plate nut (large) and the two screws.
Plate nut (large)
Rail bracket
Outer rail
Intermediate rail
B4 x8
Plate nut (large) Rail bracket
Outer rail
Intermediate rail
B4 x8
Ball retainer

1-7
MSW-A2000
MSW-A2000P
A'
A
Intermediate rails
Width : A = A' = 416 mm
15. Check that the two intermediate rails attached to the
rack are parallel.
16. To fix the two outer rails to the rack, fully tighten the
eight loosely fitted hexagon socket head cap screws in
step 12 using the L-shaped hexagon wrench.
1-6. Rack Mounting
.Mounting in rack
c
Be sure to carry the unit by the two persons or more.
17. Slide each ball retainer of intermediate rails on both
sides (left and right) in the direction of the arrow.
18. Pull equal length of each rail on both sides out.
19. Lift the unit holding the gripes on both sides, slowly
insert the inner rails into the intermediate rails.
20. While pressing each stopper of inner rails on both
sides, slowly push the unit into the rack.
n
Be careful not to catch your finger or hand in rack
mount rail.
Intermediate rail
Ball retainer
Intermediate rail
Stopper
Stopper
Inner rail

1-8 MSW-A2000
MSW-A2000P
Ornamental washer
Ornamental washer
RK5 x14
RK5 x14
21. Slide the unit in and out from the rack about three
times and check that the slide rails move smoothly.
If they are not smoothly, demount the unit and go back
to “Attaching the outer rails” (step 12).
c
When demounting the unit, carry it by the two persons
or more.
n
This unit does not have the feet at this operating.
Put down the unit on the floor or other, being careful
not to damage the unit.
22. Secure the unit to the rack with the two screws and
two ornamental washers.
Tightening torque: 120 x10_2N .m {12.2 kgf .cm}
1-6. Rack Mounting

1-9
MSW-A2000
MSW-A2000P
1-7. Matching Connectors and Cables
When external cables are connected to the connector of this unit, the hardware listed below (or equiva-
lents) must be used.
Panel indication Matching connector (cable) Sony part No. Remarks
AUDIO INPUT XLR 3P, MALE 1-508-084-00
AUDIO OUTPUT XLR 3P, FEMALE 1-508-083-00
MONITOR OUTPUT XLR 3P, FEMALE 1-508-083-00
TIME CODE IN XLR 3P, MALE 1-508-084-00
OUT XLR 3P, FEMALE 1-508-083-00
VIDEO INPUT BNC 75Z, MALE 1-569-370-12
VIDEO OUTPUT BNC 75Z, MALE 1-569-370-12
AUDIO INPUT (AES/EBU) BNC 75Z, MALE*11-569-370-12
AUDIO OUTPUT (AES/EBU) BNC 75Z, MALE*11-569-370-12
REMOTE 2 D-SUB 50P, MALE and 1-565-516-11
PARALLEL I/O (50P) JUNCTION SHELL 50P 1-563-379-11
REMOTE 1-IN (9P) 9P remote control cable
(RCC-G series) _
or
D-SUB 9P, MALE and 1-560-651-00
JUNCTION SHEEL 9P 1-561-749-00
REMOTE 1-OUT (9P) 9P remote control cable
(RCC-G series) _
or
D-SUB 9P, MALE and 1-560-651-00
JUNCTION SHEEL 9P 1-561-749-00
RS-232C D-SUB 9P, FEMALE 1-563-815-21
CONTROL PANEL 10P, MALE (connecting cable) 1-792-418-11
VIDEO CONTROL D-SUB 15P, FEMALE and 1-561-610-21
JUNCTION SHELL 15P 1-561-929-00
(OPTION) Specified by optional kit _
or
D-SUB 9P, MALE and 1-560-651-00
JUNCTION SHEEL 9P 1-561-749-00
SDI BNC 75Z, MALE*21-569-370-12
SDTI BNC 75Z, MALE*21-569-370-12
PHONE*3JM-60 stereo phone plug _
*1: Coaxial cable length : max. 600 meters (Reference value based on MSW series)
It is recommended to connect the BELDEN8281 cable or equivalent to this connector.
*2: Coaxial cable length : max. 200 meters (Reference value based on MSW series)
It is recommended to connect the BELDEN8281 cable or equivalent to this connector.
*3: It is used on the front (upper control panel).
1-7. Matching Connectors and Cables

1-10 MSW-A2000
MSW-A2000P
1-8. Signal Inputs and Outputs
1-8. Signal Inputs and Outputs
Input connectors
1AUDIO INPUT XLR 3-pin x 4 (1 set : CH1, CH2, CH3, and CH4)
Analog audio 4 channels
LOW OFF : _60 dBu, high impedance, balanced
HIGH OFF : +4 dBu (Standard), high impedance, balanced
HIGH ON : +4 dBm (Standard), 600 Ztermination, balanced
1TIME CODE IN XLR 3-pin x 1
Time code 0.5 to 18 V p-p, 10 kZ, balanced
2VIDEO INPUT, REF.VIDEO BNC x 2 in loop through connection
Outside reference video signal (Black burst or composite sync)
0.3 V p-p, 75 Z, sync negative
2VIDEO INPUT, COMPOSITE BNC x 2 in loop through connection
Analog composite video 1.0 V p-p, 75 Z, sync negative
2VIDEO INPUT, COMPONENT BNC x 3 (1 set : Y, R-Y, and B-Y)
Analog component video
Y : 1.0 V p-p, 75 Z, sync negative
R-Y/B-Y : 0.7 V p-p, 75 Z
3AUDIO INPUT (AES/EBU) BNC x 4 (1 set : CH1/2, CH3/4, CH5/6, and CH7/8)
Digital audio 8 channels
AES/EBU format, 2 channel mode, 1.0 V p-p, 75 Z
5SDI INPUT BNC x 1 (active through out x 1)
Serial digital interface (270 Mbit/s) in conformity to SMPTE 259M & ITU-R BT.656
5SDTI INPUT BNC x 1
Serial data transport interface (270 Mbit/s) in conformity to SMPTE 305M (SDTI) and
SMPTE 322M (SDTI-CP)
Remote connectors
4REMOTE 2 PARALLEL I/O (50P) D-SUB 50P connector (Refer to Optional “Interface manual” for details.)
4REMOTE1-IN (9P) D-SUB 9P connector (RS-422A interface)
Remote control
4REMOTE1-OUT (9P) D-SUB 9P connector (RS-422A interface)
Remote control
4RS-232C D-SUB 9P connector (RS-232C interface)
for ISR (Interactive Status Reporting)
4CONTROL PANEL 10P connector
for an outside control panel connection only
4VIDEO CONTROL D-SUB 15P connector
for a TBC remote controller (BVR-50) connection
4(OPTION) D-SUB 9P connector
for an optional kit
Reduced drawing of rear panel
12
5
3
4

1-11
MSW-A2000
MSW-A2000P
1-8. Signal Inputs and Outputs
Output connectors
1AUDIO OUTPUT XLR 3-pin x4 (1 set : CH1, CH2, CH3, and CH4)
Analog audio 4 channels
+4 dBm (Standard) (600 Zload), low impedance, balanced
1TIME CODE OUT XLR 3-pin x1
Time code 2.2 V p-p, low impedance, balanced
1MONITOR OUTPUT XLR 3-pin x2 (1 set : R and L)
Analog audio
+4 dBm (Standard) (600 Zload), low impedance, balanced
2VIDEO OUTPUT, COMPOSITE BNC x3 (including 1 for character superimpose)
Analog composite video 1.0 V p-p, 75 Z, sync negative
2VIDEO OUTPUT, COMPONENT BNC x3 (1 set : Y, R-Y, and B-Y)
Analog component video
Y : 1.0 V p-p, 75 Z, sync negative
R-Y/B-Y : 0.7 V p-p, 75 Z
3AUDIO OUTPUT (AES/EBU) BNC x4 (1 set : CH1/2, CH3/4, CH5/6, and CH7/8)
Digital audio 8 channels
AES/EBU format, 2 channel mode, 1.0 V p-p, 75 Z
5SDI OUTPUT BNC x3 (including 1 for character superimpose)
Serial digital interface (270 Mbit/s) in conformity to SMPTE 259M & ITU-R BT.656
5SDTI OUTPUT BNC x2
Serial data transport interface (270 Mbit/s) in conformity to SMPTE 305M (SDTI) and
SMPTE 322M (SDTI-CP)
PHONE JM-60 stereo phone jack
(Upper control panel) Analog audio
up to _12 dBu (8 Zload), unbalanced
Rear panel
75Z75Z
AUDIO INPUT (AES/EBU) VIDEO INPUT
VIDEO OUTPUT
TIME CODEMONITOR OUTPUT
AUDIO OUTPUT
AUDIO INPUT
CH7/8CH5/6CH3/4CH1/2
CONPONENTCONPOSITE
CONPONENTCONPOSITE
REF.VIDEO
OFF ON OFF ON
AUDIO OUTPUT (AES/EBU)
SDI
SDI
OUTPUT
1
2
3
(SUPER)
INPUT
CH7/8CH5/6
REMOTE 2 PARALLEL I/O(50P)
REMOTE 1-IN(9P)
CONTROL PANEL
REMOTE 1-OUT(9P) VIDEO CONTROL
RS232C
(OPTION)
CH3/4CH1/2
Y
R-Y
B-Y
B-Y
R-Y
Y1
INLR OUT
2
3
(SUPER)
CH2CH1
CH1
LEVEL
CH4CH3
LR
LOW HIGH
OFF ON
600
Z
LR
SDTI
AC IN
INPUT
OUTPUT
1
2
CH2
LEVEL
LOW HIGH
OFF ON
600
Z
CH3
LEVEL
LOW HIGH
OFF ON
600
Z
CH4
LEVEL
LOW HIGH
OFF ON
600
Z

1-12 MSW-A2000
MSW-A2000P
117
External view
3450
33 18
1-8. Signal Inputs and Outputs
REMOTE 2 PARALLEL I/O: 50-pin (female)
Pin No. I/O**
**
*1Setting change **
**
*2Signal Description
1INOFF CLOSURE SW (FF)
2 OUT XREC SW PANEL REC SW OUT
3 OUT XPLAY SW PANEL PLAY SW OUT
4 OUT XSTOP SW PANEL STOP SW OUT
5 OUT XENTRY SW PANEL ENTRY SW OUT
6 OUT XREF SYSTEM ALARM Non-REFERENCE
7 OUT XCF LOCK COLOR FRAME LOCK STATUS
8 OUT XDRUM LOCK LOCK STATUS OF DRUM SERVO
9 OUT XCAP LOCK LOCK STATUS OF CAPSTAN SERVO
10 OUT OCUE PRESET EDIT PRESET STATUS of the CUE Channel
11 OUT OTC PRESET EDIT PRESET STATUS of the TC Channel
12 OUT OOXIDE/METAL OXIDE/METAL TAPE STATUS
13 OUT OTAPE THICKNESS TAPE THICKNESS STATUS
14 OUT XSPARE SPARE
15 OUT XSPARE SPARE
16 —— —— +12V ——
17 —— —— GND SIGNAL GND
18 IN OPREROLL CLOSURE SW (PREROLL)
19 IN OSTBY ON CLOSURE SW (STANDBY ON)
20 IN OREW CLOSURE SW (REW)
21 IN OENTRY CLOSURE SW (ENTRY IN)
22 IN OSTBY OFF CLOSURE SW (STANDBY OFF)
23 IN OEJECT CLOSURE SW (EJECT)
24 OUT XREC REC STATUS
25 OUT XCH CONDITION RED CHANNEL CONDITION RED STATUS
26 OUT OASSEMBLE PRESET ASSEMBLE PRESET STATUS
27 OUT OEDIT OUT EDIT STATUS
28 OUT OEJECT OUT EJECT STATUS
29 OUT OANALOG/DIGITAL ANALOG/DIGITAL STATUS
30 OUT OREEL HUB REEL HUB STATUS
31 OUT XREM2 SETTING DATA RESET REMOTE2 SETTING DATA RESET STATUS
32 OUT XALL REC INHIBIT ALL REC INHIBIT STATUS
33 —— —— GND
34 IN OPLAY CLOSURE SW (PLAY)
35 IN OSTOP CLOSURE SW (STOP) (Continue)

1-13
MSW-A2000
MSW-A2000P
External view
51
69
External view
15
96
1-8. Signal Inputs and Outputs
(Continued)
Pin No. I/O**
**
*1Setting change**
**
*2Signal Description
36 IN OREC CLOSURE SW (REC)
37 OUT XREV LAMP REV LAMP STATUS
38 OUT ODA2 PRESET DA2 EDIT PRESET STATUS
39 OUT ODA1 PRESET DA1 EDIT PRESET STATUS
40 OUT XFWD LAMP FWD LAMP STATUS
41 OUT ODA4 PRESET DA4 EDIT PRESET STATUS
42 OUT ODA3 PRESET DA3 EDIT PRESET STATUS
43 OUT XSTOP STOP STATUS
44 OUT OVIDEO PRESET VIDEO EDIT PRESET STATUS
45 OUT OINSERT PRESET INSERT EDIT PRESET STATUS
46 OUT XSTBY ON STANDBY ON STATUS
47 OUT XPLAY PLAY STATUS
48 OUT XREMOTE REMOTE STATUS
49 OUT XALARM SYSTEM ALARM STATUS
50 OUT OPREROLL PREROLL STATUS
*1: Input ; 47 kZpull up to +5 V (close/open)
Output ; 10 kZpull up to +5 V (0 V or open)
*2: The pins described as Omark are possible to change the setting.
Refer to the optional interface manual for changing the setting.
RS-232C: 9-pin (male)
REMOTE1-IN: 9-pin (female)
REMOTE1-OUT: 9-pin (female)
Pin No. Signal
1 GND
2 RM TX(_)
3 RM RX(+)
4 GND
5 PRIORITY
6 GND
7 RM TX(+)
8 RM RX(_)
9 GND
Pin No. Signal
1 DCD ; Data Carrier Detect (Input)
2 RXD ; Received Data (Input)
3 TXD ; Transmitted Data (Output)
4 DTR ; Data Terminal Ready (Output)
5 SG ; Signal Ground
6 DSR ; Data Set Ready (Input)
7 RTS ; Request to Send (Output)
8 CTS ; Clear to Send (Input)
9NC

1-14 MSW-A2000
MSW-A2000P
External view
15
96
External view
81
915
1-8. Signal Inputs and Outputs
1-9. Switch Settings on Connector Panel
CONTROL PANEL: 10-pin (female)
Pin No. Signal Terminal voltage (V)
1 +21 V +21 V
2 +21 V +21 V
3 KEY TX (+) (Output) RS422
4 FRONT/REAR +5: FRONT
0: REAR
5 KEY TX (_) (Output) RS422
6 KEY RX (+) (Input) RS422
7 GND
8 KEY RX (_) (INPUT) RS422
9 GND ——
10 GND ——
VIDEO CONTROL: 15-pin (male)
Pin No. Signal Terminal voltage (V)
1 SYNC CONT (Input) _5 to +5
2 HUE CONT (Input) _5 to +5
3 SC CONT (Input) _5 to +5
4 VIDEO LEVEL CONT (Input) _5 to +5
5 SETUP CONT (Input) _5 to +5
6 CHROMA LEVEL CONT (Input) _5 to +5
7 REG _12V (Output) _12
8 GND ——
9 to 12 NC ——
13 Y/C DELAY CONT (Input) _5 to +5
14 NC ——
15 REG +12V (Output) +12
(OPTION): 9-pin (female)
Pin No. Signal
1 GND
2 RM TX (_)
3 RM RX (+)
4 GND
5——
6 GND
7 RM TX (+)
8 RM RX (_)
9 GND
1-9. Switch Settings on Connector Panel
When the unit is installed, be sure to perform the following
setup.
Refer to the operation manual “Section 2 Location and
Function of Parts” for setup.
.Analog audio input level/600 Ztermination switches
.75 Ztermination switch of reference video input
.75 Ztermination switch of composite video input
External view
1
3
68
109
5
2