Sony SLV-400 User manual

SON'yT. 3-756-340-21(1)
Fi o CassetteRecorder
OperatingInstructions
SLV-400
_) 1992 by Sony Corporation

Owner'sRecord
To prevent fire or shock haZard, do not expose the
unit to rain or moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCETHE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PEI_SONNEL.
This symbol is intended to alert the
user to the presenceof uninsulated
'.'dangerous .voltage" within the prod-
uct's enclosure that may be of suffi-
cient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance. (servicing)
instructions in the literature accompa-
nying the appliance.
The model number is located at the front and rear of the unit
and the serial number is on the top. Record the serial
number in the space provided below. Refer to these
numbers whenever you call upon your Sony service dealer
regarding this product. •
Model NO. SLV_400 Serial No.
INFORMATION
This equipment generates .anduses radiofrequency
energyand ifnot installedand usedproperly,thatis,in
strictaccordancewiththe manufacturer'sinstructions,
may causeinterferenceto radioandtelevisionreception.
Ithasbeentypetestedandfound tocomplywiththe
limitsfor a ClassB computingdeviceinaccordancewith
thespec!ficationsinSubpartJ of Part15of FCCRules,•
whicharedesignedto providereasonableprotection
againstsuchinterferenceina residentialinstallation.
Howeverthereis noguaranteethat interferencewillnot
occurina particular installation.Ifthisequipmentdoes
causeinterferenceto radio ortelevisionreception,which
canbedeterminedbyturningtheequipmentoffand on,
theuserisencouragedtotryto correct theinterference
byone ormoreofthefollowing measures-
Reorientthe receivingantenna.
Relocatetheequipmentwithrespect tothereceiver.
Movetheequipmentawayfrom the receiver.
Plugtheequipmentintoa differentoutletSothat
equipmentand receiverareondifferentbranchcircuits.
Ifnecessary,theusershouldconsultthedealer or an
experiencedradio/televisiontechnicianfor additional .
suggestions.The usermayfind thefollowing booklet
preparedbythe FederalCommunications Commission
helpful:
"How to Identify and Resolve Radio-TV Interference
Problems."
This booklet is availablefrom the U.S.Government
PrintingOffice, Washington, DC 20402, Stock No. 004-
000-00345-4.
Caution
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS
POLARIZED AC PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
The English language instruction manual covers
both the Canadian and U.S.A. models of the
SLV-400.
The models are the same with the exception of
the MENU screen, where LANGUAGE option
allows you to select either French or English as
your on-screen language. (See page 17 for
details)
L_t. Preliminaries
NOTE TO CATV SYSTEM INSTALLERS IN THE U.S.A.:
This reminder is provided to call the cable IV system
installer's attention to Article 82(}-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
I connected to the grounding system in the building, as
close to the point of cable entry as practical.
L

Tableof Contents
Warning ..........i.....:.;........................ ................... •..................... 2
Owner's Record ............................................... •..................... 2
Precautions ................................................. ;........................... 4
Introduction ............................................................................ 5
• Using This Manual ........;...................... ;............................... 5
Ove=view ............................................................................... 5
Hookups and Getting Started .............................................. 6
Audio/Video (A/V) Hookup .................................. .............. 7
Antenna Hookup .................................................................. 8
.Simple Cable Hookup ............................... _:....................... 10
Alternate Cable Hookup .................................................... 12
• Advanced Cable HookuP ................... •.................... •......... •14
Preparing the Remote Commander .................... _............ 17
Inserting Batteries ...................... _....................... ................ 17
Setting the Time and Date .................................................. 18
Example of Time and Date Setting ................:.................. 18
Presetting the Active Channels ......................................... 20
Presetting All Receivable Channels Automatically ..........20
Presetting Desired Channels or
Disabling Unwanted Channels ............._.......................... 21
Fine-tuning ....................,........... _................................. _....... 22
Cable TV Channel Assignment ......................................... 23
Slow Motion Playback ....................................................... 3u
Frame-by-Frame Picture ................................................. .. 39
Picture Adjustment During Variable Speed Playback ..... 39
Quick-Timer Recording ................... :...............;.................. 40
Quick-Timer Recording .................................................. 40
•-, .
Buttons Operable During Quick-Timer Recording .......... 41
Editing .................................................................... •................42
Editing from Another VCR .......................................... :...._ 42.
Editing onto Another vcR ................................................ 43
General Setup Information ................................................ 44
Setting the RF Unit ............................................................ 44
Attaching the F-type connector ...:...................... ;............. 45
Attaching the External Antenna Connector ..................... 46
Attaching the EAC-66 UV Band Separator/Mixer .......... 46
Identifying the Parts and Controls ................................... 47
Front Panel ........._.............................................. _................ 47
Rear Panel .................... _..................................................... 48
Display Window Indicators ............ :.................... :.............. 49
Remote Commander .............. .................................... :......50
Troubleshooting .................................................................. 51
On-Screen Help Messages ..._.............. .........,.................. _53
Specifications .......................................... ............................. 54
Index .................................... _.............................. ................... 55
==
_=
==
I
=
3.
w"
Q
O
o
=
m
5
U
•Playback ..................... .................... ......................... _......:...... 24
Inserting a Video Cassette ................................................ 24
Playback ............................................................................. 25
The On-Screen Display ............................................... :..... 26
Indexing Tape Contents ........................................ ............. 26
Playing Back Externally-Recorded Tapes ....................... 27
Recording TV Programs ..................................................... 28
Recording TV Programs .................................................... 28
Pausing ............................................................................... 29
Recording with the TV Off ................................................. 30
Watching One TV Program While Recording Another ... 30
Timer Recording .................................................................. 31
Setting the Timer ............................................................... 31
Overlapping Timer Recordings ......................................... 34
Checking the Timer Settings ............................................. 35
Changing or Cancelling the Timer Settings ..................... 36
Using the VCR Before Timer Recording Starts ............... 37
Variable Speed Playback .................................................... 38
Variable Speed Playback .................................................. 38
Still Picture .......................................................................... 38
Picture Search .................................................................... 38
Locked Picture Search ...................................................... 39
Skip Playback ..................................................................... 39
Preliminaries I 3

Precautions
•Operate the unit only on 120 V AC, 60 HZ.
• if.anything falls into the cabinet, unplug the unit and have
it checked by qualified personnel before operating it any
further.
• One blade of the plug iswider than the otl_erfor the
purposes of safety and will fit into the power outlet only
one way. If you are unable,to insert the plugfully into the
outlet, contact your dealer.
• Unplug the unit from the wall outlet if.you do not intend to
use it for an extended period of time. Fo disconnect the
cord, pull it out by the 101uq,never by the cord.
• •Whenthe unitisnotinuse,turn the•poweroffto conserve
energyand toextenditslife. ..
• Remove and store video cassettes after recording or
playback.
• Clean the cabinet, panel and controls with a dry, soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution.
•Do not use any type of solvent, such as alcohol or
benzine.
-o Allow adequate air circulation to prevent internal heat
build-up..
•Do not place the unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that may block the
ventilation slots.
• DOnot install the unitnear heat sources such as radiators
or air ducts, or in a place subject to direct sunlight,
ex.cessive dust, mechanical vibration or shock.
•Do not install the unitin an inclined position. It is designed
to be operated in a horizontal position only.
• Keep the unitand cassettes away from equipment with-
•strong magnets, such as microwave ovens or large
loudspeakers.
•Do not place heaVy objects on the unit.
Preliminaries

Introduction
This manual is divided into five chapters.
The chapters and their contents are as follows:
Preliminaries (page 2)
Preparation (page 6)
•Basic Operations • (page 24)
Advanced Operations (page 38)
Additional Information (page 44)
If you are using your VCR for the first time, Start from the
section "Hookups and Getting Started" (page6). This •
•section explains how to hookup, set up, and operate your
VCR so that you can start enjoying it right away.
For information about the VCR's basic operations, such as
Playback (page 24), Recording TV Programs (page 28), or
Timer Recording (page 31), see Basic Ope_tions.
If you are already familiar withthe basic operations, see
Advanced Operations.
Ifyou have any problems in operating the vcR, refer to
Troub eshoot ng Ifyour VCR isin need of repair, contact
your nearest Sony Service Center facility.
Conventions of this manual
This manual explain s operations using the VCR Remote
Commander. However, the buttons on the VCR with the
same name ormark asthose on the Remote Commander
function exactly the same as those of the Remote
Comma;haler.
When you are reading through the manual, remember:
• Buttons and switches are shown in uppercase letters.
Example: Press D PLAY.
Numbers in the illustrations correspond to numbers in the•
text..
•.d-- indicates signal flow.
• Notes and cautions are enclosed in boxes.
• On:screen displaysfor the USA model are used to explain
operations requiringon-screen menus.
Unpacking
Check that you have received the following accessories:
•Remote Commander RMT-V130F
• Size AA (R6) batteries (2)
•External antenna connector (1)
•75-ohm coaxial cable with F-type connectors (1)
• AC power cord (1)
Convenience
•DUAL MODE SHUTTLE ring
Allows quick access to a desired scene and playback at
various speeds inforward and reverse directions.
On-screen display
•On-screen display
Tape counter, cassette Speedl operation mode, and
remaining cassette length can be displayed on the TV
screen.
•TIMER SET/CHECK display
Timer recording settings can be set and checked by
referring to the TV screen.
oON SCREEN HELP message
The VCR gives a message on screen to warn that you
have attempted an incorrect operation.
FUnctions
•NOISE REDUCTIONfunction
•Reduces noiseappearing in the picture during playbackof •
a rentaltape,etc.
•Auto tracking function
Automatical!yadjuststhe trackingconditionforOptimum
picturequality.
•Timer recordings of eight programs ina month
Recordingof uptoeight"IV programscanbepreset0pto
onemonthinadvance.
•Auto head cleaner
Cleans the video heads each time a cassette is.inserted or
ejected.
'=O
o
=J
o
Preliminaries I 5

HookupsandGettingStarted
Before you can use yourVCR for.the first time, you.need to
connect it to your TV andset it up to receive programs for
-. viewing and recording. This sec_tionexplains how to hook up,
set up, and operate your VCR so that you can start enjoying
it rightaway. There are, however, many types of TVs
available and many different ways in which your TV can be
hooked up. As a result, this manual describes several ways
your VCR can be connected.
1o hook up your VCR so that it works best for you, first scan
through this section to find the diagram that best illustrates
the way your TV Jscurrently connected (antenna or
cable/cable box). Then use the accompanying diagrams and
procedures to complete your VCR's connections.
After you've completed the connections, follow the
instructions for setup. (Dudng setup, if you need more details
of the procedures described, page numbers are provided
where you Can find complete, step-by-step instructions.)
After you've completed the setup, you're ready to use your
VCR. Follow the instructions provided in "To Watch the TV,"
"To Watchthe VCR," and "To Record A Program" for your
specific hookup.
qlAgain, if you need step-by-step instructions, page numbers
are provided where you can find this information.)
Befo_:emaking the connections, check the following points:.
•Turn off the power to the VCR and TV.
• Do not connect the AC power cord until all of the
connections are completed.
• Make connections firmly. Loose connections may cause
picture distortion.
• If your TV doesn't match any of the examples provided,
• consult your nearest Sony dealer or qualified technician.
Caution
Connections between the VCR VHF/UHF OUT
connector and the antenna terminals of a TV receiver
should be made only as slnowninthe instructions.
Failure to do so may result in operation that violates the
regulations of the Federal Communications
Commission regarding the use and operation of RF
devices. Never connect the output of the recorder to an
antenna or make simultaneous (parallel) antenna and
recorder connections at the antenna terminals of your
receiver.
41=P
Preparation

HookuP1
Ifyour -I-Vhas audio/video (A/V) input jacks, you will get a
better picture if you hook up.your VCR using these
connections.
If your -I-Vdoesn't have A/V inputs, see the following pages
for antenna or cable hookup.
If you only wish to play back pictures and movies, you're
finished after you've made these connections. If you want to
recordoff-air or off your cable TV system, please do the A/V
hookup on this page first, then proceed to the following
pages for antenna or cable hookup•
o
x"
1#1
=1.
II,
el
If,
Preparation 7

Hookupsand GettingStarted
Hookup2
Ivlake the following connections if you're using an antenna (not cable TV). Check the type of antenna you.are using and choose
the appropriate connection. ..
8 I Preparation

•1 Set the RF Unit on the VCR's rear panel to CH3 or
CH4.
If you made A/V connections, skip this step.
qmlmtlRmmm
2SetNORM/CATVtoNORM. '\
Press MENU. Select TUNER PRESET.
Set to NORM.
Detailsale onpage 20.
3Preprogram the channels into the VCR.
PressMENU. Select TUNER PRESET.
TIMERSET/CHECK
•TUNER
CLOCK
8
Select AUTO PRESET,
then press EXECUTE.
•A_ PP_SE'r
Details are on pages 20 and 21.
Press MENU.
1- Select CLOCK SET.
J
Set time then
press EXECUTE.
•Details are on page 18.
To Watch the TV
1 Turn your VCR off, or press the VCR's TV/VTR button
untilthe VTR indicator in the display window goes off.
2 Tune the TV normally.
To Watch the VCR •
1 Tune the.l-V to CH 3 or CH 4, whichever you set on the
back of the VCR. (If you made the A/V connections on
page 7, set your TV to the A/V inputinstead.)
2 Insert a cassette and press I> PLAY.
Details are on page 24.
•To Record a Program ""
1 Insert acassette.
2Press MENU.
3 Select TIMER SET/CHECK.
4 Press EXECUTE.
5Set DATE, START time, STOP time, channel and tape
recording speed.
6 Press EXECUTE and then TIMER REC (ON/OFF).
Details are on pages 31 and 32.
=
=
.ll.
U'J
O
==,
Preparation I 9

Hookunsand GettingStarted
Hookup3
Recommended Use:
Since this is the simplest,hookup, we recommend that
you try this hookup first. If you cannot record the
channels you want, you'll need to change your hookup
to one of the choices on the following pages, or contact
your cable Company for assistance.
Background
This VCR can record virtually any unscramb!ed cable
channel. Some cable systems "scramble" specific channels,
usually premium or pay-per-view channels. You will not be
able to record scrambled channels with this hookup.

1Set the RF unit on the VCR's •rear panel to CH3 or
CH4.
If you made A/V connections, skip this step.
2Set NORM/CATV to CATV.
PressMENU. SelectTUNER PRESET.
MB_J
$
Set to CATV.
Detaiis are on page 20,
3Preprogram the channels into the VCR.
PressMENU. Select TUNER PRESET
I-I J
"I1MERSk"r/GH_CK
I,
!
SelectAUTO PRESET,
then press EXECUTE.
PRESEI" CHI I
N_qM_,_3V I
J- _€,'TOPI_IEI"t :: i
M_u_._r ,Aoo _I
J
Details are on pages 20 and 21.
Press'MENU. select CLOCKSET.
" " ! "" "
Settime then
press EXECUTE.
Details are on page 18.
To Watch the TV
1' Turn your VCR off, or press the VCR's TV/VTR button
untilthe VTR indicator in the display window goes off.
2 Select the channel with your cable box (if you have one).,
or directly tune with your TV (if you don't).
To Watch the VCR
la If you didn't use the A/V input:
• Turn ON the cable box.
• Select CH 3 or CH 4 on the cable box (whichever you
set on the.back of the VCR).
•Select the output channel of the cable box (usually 2, 3
or 4) on your TV.
lb If you made the A/V connections on page 7-
Set your TV to the A/V input.
2 Insert a cassette and press I> PLAY.
Details are on page 24.
To Record a Program
1Insert a cassette.
2 Press MENU.
3 Select TIMER SET/CHECK.
4 Press EXECUTE.
5Set DATE, START time, STOP time, channel and tape
recording speed.
6 Press EXECUTE and then TIMER REC (ON/OFF).
Details are on pages 31 and 32.
==
a
==
!i_
.=
=3.
Pre a,at n11

HookupsandGettingStarted
Hookup4
Recommended Use:
This hookup willallow you to record either scrambled or
unscrambled channels. However, you will have to set
the channel on the cable box for each program you
want to record. If your cable system only scrambles all
or most channels, you must use this hookup. If your
.cable system scrambles a few channels, you may
prefer Hookup 3 or 5 (on pages 10 and 14,
respectively). Please note that Hookup 3 will not allow
•you to record scrambled channels.
Hookup 5 will allow you tOrecord either scrambled or
unscrambledchannels, but will require that you
purchase a few extra parts at Your local electronics
store.
Background
This VCR can record virtually any unscrambled cable
channel. Some cable systems "scramble" specific channels,
usually premium or pay-per-view channels. Although this
hookup will also allow you to record these scrambled
channels, you must use the cable box rather than the VCR to
select channels.
12!Preparation

1Set the RF Unit on the VCR's rear panel to CH3 or
CH4. If you made A/V connections, skip this step.
2Switch on your cable box. \
3Preprogram the channels into the VCR.
PressMENU. Select TUNER PRESET.
SelectAUTO PRESET,
thenpressEXECUTE.
Details are on pages 20 and 21.
Press MENU. Select CLOCK SET.
J
Set time then
press EXECUTE.
Details are on page 18.
To Watch the TV
1 Turn your VCR off, or press the VCR's TV/VTR button
until the VFR indicator in the display window goes off.
2 Switch on your cable box.
3 Tune the TV to the cable box output channel
(0sually 2, 3, or 4).
4 Select the channel that you want to watch with your cable
box.
To Watch the VCR
1 Tune the "IV to CH 3 or CH 4 (or to A/V input if you made
A/V connections).
2 Insert a cassette and press I> PLAY.
Details are on page 24.
To Record a Program
1 Insert acassette.
2 Switch on the cable box.
3 Select the channel you wish to record on the cable box.
4 Press MENU, and select TIMER SET/CHECK, and press
EXECUTE.
5 Set DATE, START time, STOP time, Channel and tape
recording speed.
The channel number must be the same as the cable box
output channel (2, 3 or 4).
6 Press EXECUTE and then TIMER REC (ON/OFF).
7 Leave the cable box ON.
l-1_f_il_ _r_ rtn n_€1_€: _11 _n¢l t':t9
_..
S
"l=.
tbt
=]
€ID
O,,

HookunsandGettingStarted
Hookup5
i
Recommended Use:
By using the A/B switch, this hookup allows you to
record unscrambled channels directly with the VCR
(position "A"). You only use position "B" and the cable
box if you want to record a "scrambled" channel. This
gives you the most convenient operation of the VCR's
timer.
Background
ThisVCR can record virtually any unscrambled cable
channel. Some cable systems "scramble" specific channels,
usually premium or pay-per-view channels. This hookup will
allow you to record unscrambled channels by selecting "A"
on the A/B switch, and tuning the channel di_'ectlyon your
VCR. To record "scrambled" channels,.select "B" Onthe
A/B switch, and select the channel using the cable box. If
your cable system scrambles all or most channels, you must
use the alternate cable hookup (Hookup 4) on page 12.
14 I Preparation

1 Set the RF Unit on the VCR's rear panel to CH3 or
CH4. If you made A/V connections, skip this step.
2Set the A/B switch to 'A'.
3Set NORM/CATV to CATV.
\
5 Add the cable box output channel (usually2, 3, or 4).
PressMENU.
l= TIMER SET/CHECK
_PRESET
CLO¢_ _'T
Select"F1JNERPRESEt.
!
PressEXECUTE.
SelectMANUALSET.
11JNER _
Addthecable boxoutput
channel (usually 2, 3 or 4). .o_,c_wAUTO
For example, press3 and j
ENTER,set toADD, then
pressEXECUTE.
Details areon page21.
===
==
==_
m
=l.
Press MENU. SelectTUNER PRESET.
I"MER s_-'rR=_lEC_
Pl'uN6_ PRIIESE'r
Details are on pages 20.
.
•Setto CAFV.
]IJNER PRESt'r CH1
4Preprogram the channels into the VCR.
PressMENU. SelectTUNER PRESET.
!
SelectAUTO PRESET,
thenpress EXECUTE.
Details are on pages 20 and 21.
Press MENU. select CLOCK SET.
Details are on page 18.
.
Settime then
Preparation 15

HookupsandGettingStarted
To Watch the "IV
1 Turn your VCR off, or press the VCR's TV/VTR button
until the VTRindicator in the display window goes offl
2 Set the A/B switch tOB.
3 Switch on your cable box.
4 Tune the TV to the cable box output.channel (usually 2,3
or 4).
5 Select the channel you want to watch with your cable box.
6 After watcing the TV, please remember to return the A/B
switch and cable box channel to the correct position.
To Watch the VCR
1 Tune the TV to CH 3 or CH 4, (or to A/V input if you made
A/V connections.)
2 Insert a cassette and press I::>PLAY. "
Details are on page 24.
To Record a Program Using the Timer
•Unscrambled Channels
i Insert a cassette.
2 Switch the A/B switch to "A".
3 Press MENU and select TIMER SET/CHECK.
4 Press EXECUTE.
5 Set DATE, START time, STOP time, Channel and tape
recording speed.
6Press EXECUTE and then press TIMER REC (ON/OFF).
7 Leave the A/B switch in "A".
• Scrambled Channels
1 Insert a blank cassette.
2' Switch the A/B switch to "B".
3Switch on your cable box.
4 Select the channel you want to record on the cable box.
5, Press MENU and select TIMER SET/CHECK.
6Press EXECUTE.
7' Set DATE, START time, STOP time, Channel and tape
recording speed.
The channel number must be the same as the cable box
output channel (2, 3 or 4).
8Press EXECUTE and then TIMER REC (ON/OFF).
9Leave the A/B switch in "B".
Datails are on pages 31 and 32.
16IPreparation

Preparingthe RemoteCommander
2
3
Press •or •.to move the cursor to LANGUAGE.
Press EXECUTE.
The language menu screen appears.
4Press < or •to select ENGLISH or FRENCH.
.=
mi
=
€1
m
;Z
IB
11.
"u
"Ca
I:1
m
mm
UP
[]
c=
[]
[]
m
:l
Notes on the handling of batteries
• With normal use, the batteries should last for
•approximately six months.
• If you do not use the Remote Commander for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage.
•Do not use a new battery together with an old one.
Do not use different types of batteries.
_"J _.-__ ;F-_-F_ [_;]in]'_, [-_
i['-_ _ i[l_ •nl':.ln_ LI_{O]'_l_n[o] alLql'P,l aT'=ToI P-Iii_'k:,,) d,,,-,]|_li
You can set select your VCR to display screen information in
either English or French.
Select the menu language before using your VCR following
procedure.
1PressMENU
The mainMENU appears.
5 Press EXECUTE.
Now that the menu language setting is over, the main MENU
appears in your selected language whenever you press
MENU.
You can control both the VCR and some Sony TVs with the
Remote Commander. You must set the TV/VTR remote
control selector to the "TV" or "VTR" position depending on
whether you want to control the VCR or the TV.
TV/V'rR remote
control selector
J
When controlling the VCR;
Set the TV/VTR remote control selector to the "VIR"
position.
When controlling a Sony TV
Setthe TV/V'IR remote controlselectortothe'"IV"
position.
The buttonsmarkedwitha smallyellowdot canbeusedto
controlSonyTV setsbearingthe [] mark.
Preparation 17

SettingtheTimeandDate
YoucansettheVCRtimeanddateontheTV screenusing
theRemoteCommander.
1 PressMENU.
The main MENUappears.
2 Press •or •to move the
cursor (1_)to CLOCK SET.
_. "rIMERSET/CHECK
TUNER PRESET
CLOCK SET
3Press EXECUTE.
"1/1 1993 FR112:00 AM"
is displayed. The leftmost
1, in the "month"
position, flashes.
4Press ior •until 7
appears in the month
position.
5 Press I_ to make the next
number in the "day"
position flash.
;ili!iii!ii i! 7_!!!_
6Press Ior •until 4
appears in the day
position.
The day of the week is set
automatically.
1 8 I Preparation

7Press I_ to make the year
flash and press Aor vto
change the year,
Ifyou wantto leave the
year indication unchanged,
just press I_,
8 Press I_ to make the time
flash.
9 Press 8or Vuntil 3 PM
appears.
Cl.OCKsE'r A •
\
•10 PressI_to make the
minutes flash.
11 Press •or vuntil 32
appears in the minutes
position.
12 Press EXECUTE to start the clock.
Pressing EXECUTE will set the Clockto 3:32 pm 00
seconds.
:T
=1
a_
w
:l
el_
m
NOTES:
•Do not set the time and date during timer-activated recording, timer recording standby or quick-timer recording.
•When the time and date clock is displayed, the clock keeps running as long as no changes are made. The seconds are not
reset to 00 when you return to the original screen.
Preparation 19

Presettingthe ActiveChannels
This VCR is capable of receiving VHF channels 2 to 13, UHF
channels 14 to 69 and CATV channels 1 to 125. These
channels can be preset using the Remote Commander and
the TUNER PRESET display. First, we recommend that you
preset the active channels in your area using the automatic
preset mode. Then, if there are any unwanted channels,
disable them manually. If you have already decided which
channels you wish to preset on the VCR, set them directly
using the channel number buttons.
Before presetting channels, check the following points:
• Turn ON the VCR and theIV.
•Ifyou have connected the TV and the VCR using the
VHF/UHF OUT on the VCR only, make sure that the TV is
set to the correct channel (CH 3 or CH 4) for the VCR.
Ifyou have connected the "IV and the VCR using the LINE
OUT, select the input for the VCR.
• Press TV/VTR so that the VTR indicator lights up in the
display window on the VCR.
•Press INPUT SELECT so that achannel number appears
in the displaywindow on the VCR.
Press MENU.
The main MENU appears.
2
4
Press aor wto move the
cursor (1_)to TUNER
PRESET.
MENU
ws_r/or=_
Press EXECUTE.
The TUNER PRESET
menu is displayed.
Press ,= or wto move the
cursor to NORM/CATV.
20 I Preparatl°n