Sony SLV-760HFPX User manual

H MECHANISM
OPERATION MANUAL
SONY

Contents
1. Main parts layout diagram .......................................................................................... 3
2. Tape path .................................................................................................................... 4
3. Cassette IN _ Loading ---" Stop ................................................................................. 5
4. Stop _ Playback ...................................................................................................... 11
5. Stop _ Power OFF .................................................................................................. 13
6. Playback _ CUE ..................................................................................................... 15
7. Playback ---"REV ..................................................................................................... 17
8. Stop _ Fast forward (FF) ........................................................................................ 19
9. Stop _ Rewind (REW) ............................................................................................ 23
10. Stop ---"Unloading _ Eject ...................................................................................... 27
M, 2_

1. Main parts layout diagram
Drum (M901) ACE head Capstan motor
(M902) roller
FE head
End sensor--
T/S LED _
Cassette IN
switch
!
S reel (PH40t) (PH402)
sensor
Rotary encoder
(cam gear)
T reel
Cam motor
(M903)
Fig. 1-1
-_- R17

2. Tape path
TG4 TG5 ACE head
TG3 Drum (M901) TG6 TG7
Capstan motor
(M902)
FE
TG2
TG1
TG8
Pinch roller
Top sensor
End
S reel T/S LED T reel
Fig. 2-1
-- A--

3. Cassette IN --- Loading --- Stop
Cassette loading. [
+
I Right claw is released. [
+
[ Left claw is rcleased. ]
[Cassetteholderslidesinthedirectionofarrowmark (_)'1
Left arm swings and cassette IN lever is released form [
i
cassette IN switch. I
+
I Cam molor is rotated. [
[ Worm wheel is rotated. ]
[ Cam gear is rotated. I
[ FL driving gear is rotated. [
[ Gear slide plate slides. ]
[ Relay gear rotatcs to swing right/lefl arm. [
+
Cassette holder is retracted to set cassette in DOWN
position. +
Cassette IN switch is pressed by cassette IN lever.
+
(Continues to loading)
(see Page 7-8)
Cassette IN sw___
\
Left claw
Cassette
CasseHe
Left arm
CassettelN lever
J
Cassette holder
Fig.3-1
Right claw
FL driving gear
!
Gear slide plate
Right arm
Relay gear
- _-G19 - 6-- G20

0Pinch roller moves Capstan shaft O Pinch arm moves in the direction of
arrow mark _)and contacts capstan
of arrow mark _. shaft..__e_!___ Capstan shaft
O _ _,__,_!_ II _ Pinch roller
'An opening _) is
_ I*"/'_0 '_'1_ IL_r-_ given between
_,,,/_,.__.._/_'\"_ ',_ pinch rollor and
Press gear ,_'<:_=_=_/' \Press gear pinch block by
\ press gear cam.
O Press gear and elevator gear /_ Pinch\ roller is pressed in the direction
are rotated in the direction of // of arrow mark _) by the tension of spring.
arrow mark 0. /
_1 Pinch block moves in the direction of
arrow mark O through press gear cam.
O
Elevator
Fig.3-2
Main slider moves in the direction of arrow mark O,
and RKB arm pushed up by step _) moves in the
direction of arrow mark I_.
?arm
Pendulum gea_ riming belt
Pendulum gear RKB brock i_ RKB arm moves in the direction of
arrow mark i_, then RKB block moves
in the direction of arrow mark i_ to
i_ change the mesh of pendulum gear.
Timing belt
Fig.3-3
Shuttle (T)
Drum
TG1 arm
Shuttle
Tension reg_
band
Fixed release arm
Soft brake (S)
Pendulum
compulsion
arm
Capstan motor (M902)
(Capstan shaft)
TG8 arm Pinch roller
MC roller MC arm
S reel RKB brock Treel
Pendulum gear
Idler gear (S) Neutrality arm
gear
Pinch arm
Press gear
gear
FL driving gear
Upper/Lower
gear
RVS brake arm
brake (T)
Main brake (T)
Cam motor
(M903)
Capstan motor Loading gear (T)
(M902)
\ Capstan brake Drum (M901)
Upper/L°wa_ron _ I{'--"
gFi_nvln ear -__
'gg __
Cam gear ,_,_
Cam motor
(M903) L_.L______
Worm wheel RKB brock RKB arm
Idler gear (S) S reel
j Loading gear (S)
Main slider
belt
Fixed
release arm
Fig.3-4
H3 -,o- H4

4. Stop Playback
Drum is rotating. ]
Press PLAY button. ]
I Capstan motor is rotated, l
RKB block is rotated through
dining belt (clutch ON).
Pendulum gear is meshed with
dler gear (T) and rotated.
[ T reel is rotated. J
f
[ Pinch roller is rotated. J
Drum (M901) Capstan motor (M902)
(Capstan shaft)
Idler gear (S) Pendulum gear T reel
RKB brock Idler gear (T)
Capstan motor
(Mc02) N
RKB brock --_ k_ __'.._ _.._/_
Tre_l_ ,dlerg_; P_-nd!_ _ear(S) J-
Fig. 4-1
roller
compulsion arm
/- Tension wheel
t Timing belt
--ll-- --12--

5. Stop -- Power OFF
Soft brake (T)
soperated.
Pinch-block
moves in the
directionof
arrow mark
and pinch
roller is
released from
capstan shaft.
I Press power button.
I Cam motor is rotated,
I Worm wheel is rotated.
I Cam gear is rotated.
Upper/Lower
communication gear is
rotated. t
I TG8 gear is rotated. [
I Press gear is rotated. I
[ Elevator gear is rotated. ]
•_If power is ON, it turns OFF
automatically about 5 minutes later.
L
Main brake (S/T)
is operated. [
Brake is given
to S/Freel.
Main slider slides.- ]
RKB arm is ] Pendulum INeutrality arm
pressed, compulsion arm [is operated.
is operated. I
RKB block 1
moves down.
I
I RKB block becomes free. I
[ Pendulum gear is released from T reel. ]
Tension
band
Fixed release
S
Drum (M901)
Main brake (S) RKB brock
Pendulum compulsion
arm
Capstan motor (M902) Elevator gear
(Capstan shaft) /
Pinch roller/ Pinch arm
_/--//_/ //Pinch block
o J
_/_ j Press gear
--, TG8 gear
_/ Upper/Lower
_l_--_ "_'_" communication
_/-"__ Solt brake(T)
..... _-"_'-'-'- Cam motor
--_ (M903)
Main brake (T)
Neutrality arm
Fixed release arm is
operated.
Tension regulator band
tenslon becomes weak to
make Sreel brake weak.
Fig. 5-1
Capstan shaft
0Pinch block isoperated and pinch roller
moves in the direction of arrow mark
until it isreleased from capstan shaft,
Pinch brock
block
Press,
O Press gear is rotated in the direction of arrow mark 0
and pinch block pin pushed to press gear cam is
released from cam while pinch block moves in the
direction of arrow mark I_.
Fig. 5-2
Capstan motor Capstan brake Drum (M901)
Upper/Lower
commu
gear Main slider
Cam
Cam moto
(M903) Worm wheel Pendulum gear
Idler gear (T) RKB arm
Fixed release
arm
--13-- H7 -14-- H8

6. Playback CUE
I Drum is rotating. I Capstan motor is rotated at
high speed.
RKB block is rotated I
through timing belt.
(clutch ON)
Pendulum gear and idler gear
(T) are rotated at h gb speed.
IT reel is rotated at [
|
high speed. !
f
Pinch roller is rotated 1
at high speed.
•_Difference from (Stop -- Playback)
(_) Capstan motor is rotating at high speed.
(_) Pendulum gear is meshed with
idler gear (T) from the beginning.
RKB brock
Treel
Drum (M901) Capstan motor (M902)
(Capstan shaft)
Pendulum gear T reel
Idler gear (S) Idler gear (T)
Capstan motor
(Mi02) N
Idler gear (T) Pendulum gear
Fig. 6-1
•Pinch roller
Tension
Timing belt
-- 15-- -- 16--

7. Playback -,- REW
Cam motor is rotated. ]
] Wonn wheel is rotated. [
[ Cam gear is rotated. [
I
i
Brake is given to T reel by I
reverse brake ann.
Fixed release / Brake is given
l
arm is operated: [ to S reel by
soft brake (S).
(TG1 tension )
\ becomes weak.
Main slider slides.
S reel
SrWi_ing__
Main slider"- IWhen main slider moves in the direction of
arrow mark _), S winding arm pressed by
main slider cam moves in the direction of
arrow mark(_ and S reel is rotated a little
in the direction of arrow mark.
Drum is rotating. I
Pendulum I l
compulsion
ann is operated.
JPendulum
is free on [.Capstan motor is rotated
gear
S reel only. lin reverse at high speed.
!
RKB block is rotated ]
I
through timing belt.
(clutch ON)
Pendulum gear is
meshed with idler gear
(S) and rotated.
Brake is given to [ S winding ann is
capstan motor by I operated to slightly
capstan brake. ] rotate S reel. ]
S reel is rotated in
reverse at high speed.
f
Pinch roller is
rotated in
reverse at high
speed.
Fig. 7-1
Drum
TG1 arm
arm
RKB
Pendulum
compulsion arm Capstan motor (M902)
(Capstan shaft)
S reel Pendulum gear Treel
Soft brake (S) Idler gear (S) RKB brock
Capstan brake
Tension wheel
Capstan motor (M902)
Cam motor
(M903) Pendulum gear Idler, S reel
Fig. 7-2
gear
gear
rG8 gear
Upper/Lower
;ommunication
gear
S brake arm
Cam motor
(M903)
slider
belt
Fixed release
arm
Hll -18- H12

8. Stop ---,Fast foward (FF)
When this operation is mode ICam motor is rotated. ]
before cassette tape is loaded for /
playback, CUE mode is started J_
to read tape signal and then tape T
is set in fast forward mode. [Worm wheel is rotated. I
II
+
Upper/Lower
communication
gear is rotated.
Brake is given to
IT reel by soft
Lbrake03.
[Cam gear is rotated. I
+
I Main slider slides. ]
+
TG8 gear is
rotated.
Press gear is
rotated.
Fixed release
arm is operated
to make TG l
arm tension
weak.
i
Brake is given
to capstan motor
IbYcapstan
lbrake.
IPinch miler is
released from
capstan shaft.
IDrum is rotating. ]
+ +
_rak0isgiveoII_rakeisgiveoI
to S reel by [to T reel by
main brake (S). main brake (T).
,r
Trigger lever Islides. I
+
Neutrality arm
is operated. ]
Pendulum
[compulsion arm
is operated.
+
IKB blockis l
set in clutch
OFF by RKB
alTO.
Pendulum gear is locked
in the center between J
S reel and Treel. ]
Capstan brake is IMain brake <S) IIMain brake (T)
released from [ is released ]Iis released
capstan motor, from S reel. J [form T reel.
Neutrality arm is
operated again.
I
Pendulum
compulsion arm
is operated.
Capstan motor is rotated at
h gh speed. +
(;e?d_lUrTgere_a;.is free °n )
I
!
RKB block is rotated I
I
through timing belt.
m
Pendulum gear is meshed I
I
with idler gear 03 and
rotated. +
T reel is rotated at high I
1
speed.
-- 19-- -20-

Pendulum
arm
Drum (M901) Capstan motor (M902)
TG8 gear (Capstan shaft) Pinch roller Elevator gear
Main brake (S) block
gear
Upper/Lower
gear
eutrality arm
brake (T)
(T)
Fixed release
arm
S re/el Pendulum gear T reel
RKB brock Idler
Cam motor
(M903)
Capstan brake Drum (M901)
Capstan motor Tension wheel
(M902)
Upper/Lower
communication
gear Main slider
Cam gear =be_
RKB Main brake (S)
Cam motor
(M903) Worm wheel Idler gear (T) Trigger lever RKB arm
T reel Pendulum gear Idler
Fixed release
arm
Fig. 8-1
-_- H15 - _- H16

9. Stop --" Rewind (REW)
•_When this operation is mode [
before cassette tape is loaded for n
playback, REV mode is started
to read tape signal and then tape I
is set in rewind mode. I
+
"_eis_veo_ll
T reel by soft ]
brake03. ]
Upper/Lower
communication
gear is rotated.
TG8 gear is
rotated.
Press gear is I
rotated.
Pinch roller is
released from
capstan shaft.
Cam motor is rotated.
Worm wheel is rotated.
+
Fixed release
arm is operated
to make TG 1
arm tension
weak.
Cam gear is rotated.
I Main slider slides.
I
+
Brake is given
to capstan motor
by capstan
brake.
Drum is rotating. [
I
I
I
+ +
_rakeis_ivonIIorakeisgivenI
to S reel by to T reel by
man brake (S). main brake (T).
Trigger lever
slides.
_ I I
Neutrality ann
is operated.
Pendulum
compulsion arm
is operated.
Pendulum gear is locked
in the center between
S reel and T reel.
1€
Capstan brake is
released from
capstan motor.
f
Main brake (S)
is released
from S reel.
I
Main brake (T) I
IIisreleased
I
][formTr_l
it
Neutrality ann is
operated again.
I
Pendulum
compulsion arm
is operated.
(eende_lUr_gre2;.isfree on )
I
+
RKB block is
set in clutch
OFF by RKB
arm.
i
Capstan Motor is rotated I
I
in reverse at high speed.
I
RKB block is rotated t
I
through timing belt.
-I l
Pendulum gear is meshed I
I
with idler gear (S) and
rotated.
S reel is rotated in |
J
reverse at high speed.
-- 23- -- 24-

Pendulum
com
arm
Drum (M901)
\Capstan motor (M902)
(Capstan shaft)
TG8 gear Pinch roller gear
Main brake (S)_ _h block
gear
Upper/Lower
gear
' arm
Main brake (T)
Fixed release
arm
S reel RKB brock T reel
Idler gear (S) Pendulum gear
(T)
Cam motor
(M903)
Capstan brake Drum (M901)
Capstan motor Tension wheel
(M902)
Upper/Lower
co
gear belt
Cam gear erlever
RKB brock Main brake (S)
Cam motor
(M903) Worm wheel Pendulum gear RKB arm
Idler gear (T) _ear (S)
Fixed release
arm
S reel
Fig. 9-1
-_- H19 - _- H20

10. Stop Unloading Eject
Brake is given
to capstan
[motorby
Lcapstanbrake.
Swinding arm is
operated _ rotate
S reel a little.
Cam motor is rotated. ]
IWorm wheel is rotated. I
[ Cam gear is rotated. ]
IMain slider slides. I
I
Brake is givenIFiaxed Brake is given
to S reel by release arm to T reel by
soft brake (S). is operated, man brake (T).
[w°laI
unloading. J
Tension regulator
band releases the
brake from S reel.
IDram is rotating. [
Loading gear I(T) is rotated.
I
Loading gear
(S) is rotated.
Shuttle (S) ] Shuttle (T) ]
unloading, unloading.
Drum ]
cleaning by
MC roller.
RKB block is
set in clutch
OFF by RKB
arm.
Main brake (T) ]
is released from I
T reel.
Pendulum
compulsion
arm is operated.
'Pendulum gear
is free on S reel
only.
1
Reverse brake
arm gives
brake to T reel
landisreleased
immediately.
Upper/Lo.wer
commumcatlon gear is
rotated. I
]_essgearisrotated]
I
released from rotated.
capstan motor.
[PinchrollermovesupJ
[ TG8 ann unloading. ]
Capstan motor is
rotated.
RKB block is
rotatedthrough
timing belt.
(dutch ON)
-1
I Pendulum gear is I
meshed with idler
gear (S) and rotated.
[S reel is rotated. J
( Tape is wound
into cassette. /
ICapstanmotor .l
i, I
FL driving Brake is I
Igear is [ Igiven to [
I
Treelby I
soft brake
(T).
I Cassette OUT Ioperation.
(see Page 31, 32)
-- 27- -- 28--

Shuttle (S)
Pendulum
compulsion Capstan motor (M902)
arm \ MC arm (Capstan shaft)
Drum (M901)_Shuttle (T) TG8 arm Pinch roller
Elevator gear
TG1 arm
Pinch arm
gear
Tension regulator
band
TG8 gear
Upper/Lower
communication
gear
FL driving gear
RVS brake arm
Soft brake (T)
arm
Soft brake (S)
S reel Pendulum arm T reel
Idler gear (S) RKB brock
Main brake (T)
Cam motor
(M903)
Capstan motor
(M902) Shuttle (T)
Capstan brake Drum (M901)
Shuttle (S)
Upper/Lower
gear
slider
FL dr v n!
Cam i
Cam motor
(M903) Worm wheel RKB arm Idler gear (S)
ed release
arm
S reel
Fig 10-1
in) Main slider moves in the direction
of arrow mark Oand RKB arm is
pushed up in the direction of
arrow mark 0 by step (_). Main slider
RKB brock
Pendulum gear riming belt
OWhen RKB arm moves in the direction of
Pendulum gear RKB brock 7 arrow mark 0, RKB block moves in the
II , ] /I J direction °f arr°w mark 0 t° change
/ ! [' _ /10 the mesh ofpenduumgear
i, I 1 1I ','.'l,-
i' [ _ _ 7 ing Oelt
I
Fig. 10-2
0Pinch roller moves up in the
direction of arrow mark 0.
shall
0 Pinch arm moves in the direction of
arrow mark 0 and pinch roller is
released from capstan shaft.
haft
gear
Elevator gear
• Press gear and elevator gear
are rotated in the direction of
arrow mark 0.
Pinch roller
I Press gear
0 Pinch block pushed by
press gear cam moves
in the direction of
arrow mark 0.
Fig. 10.3
- I-3 - I-4

Door is opened by
door lever.
(From unloading)
IGear slide plate slides.
I Relay gear is rotated to swingright/left arm.
Cassette IN lever is released
form cassette IN switch.
Cassette IN switch is pressed by
cassette IN lever.
ICam motor stops. ]
[
[
Cassette holder slides.
Cassette is ejected.
1
1
Doorlever
Cassette IN level
Cassette IN !
Left arm
<>
Cassette IN level
Left arm
Cassette holder
FL driving gear
Right arm Gear slide plate
Cassette Relay gear
Fig. 10-4
-- 3l-- -- 32--