Sony SLV-SE310 User manual

D:\WINNT\Profiles\Y3_ichikawa-w\Desktop\nakui sagyo\1016\3065679111 SLV-SE310
QSG\GB1EX.fm masterpage:Singlecolumn-Right
SLV-SE310 QSG
3-065-679-11 (1) GB
Video Cassette Recorder
Sony Corporation © 2001
Quick Start Guide
3-065-679-11 (1) GB
This Quick Start Guide will introduce you to the essential
procedures for using your VCR. Use the Auto Set Up function
to preset all of the receivable channels. Then follow the
additional steps in the Operating Instructions to change the
programme position to your favourite order.
1Unpacking
2Inserting the batteries
3Connecting the VCR
4Using the Auto Set Up function
5Tuning your TV to the VCR
1Unpacking
Check that you have received thefollowing items with the VCR:
2Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and – on the
batteries to the diagram inside the battery compartment. Insert
the negative (–) end first, then push in and down until the
positive (+) end clicks into the position.
3Connecting the VCR
1Connect the aerial to AERIAL IN of the VCR.
2Connect AERIAL OUT to the aerial input of your TV using
the supplied aerial cable.
3 For better picture and sound, connect LINE-1 (TV) to your TV
using a Scart cable if your TV has a Scart (EURO-AV) connector.
4Connect the mains lead to the mains.
4Using the Auto Set Up function
You can preset channels.
Hold down AUTO SET UP for three seconds.
When all of the receivable channels are preset, “SET UP”
disappears from the display window. You can rearrange the
programme positions to your favourite order (see “Changing/
disabling programme positions” in the Operating Instructions).
Dew caution
If the VCR is brought directly from a cold to a warm location,
moisture may condense inside the VCR and cause damage to the
video head and tape. When you first install the VCR, or when you
move it from a cold to a warm location, wait for about three hours
before operating the VCR.
• Remote commander • Aerial cable
• R6 (size AA)
AERIAL IN
AERIAL
OUT
: Signal flow
iLINE-1
(TV)
2
3
4
1
AUTO SET UP
VCR’s display window

D:\WINNT\Profiles\Y3_ichikawa-w\Desktop\nakui sagyo\1016\3065679111 SLV-SE310
QSG\GB1EX.fm masterpage:Right
SLV-SE310 QSG
3-065-679-11 (1) GB
5Tuning your TV to the VCR
If your TV does not have a Scart (EURO-AV) connector.
1Press RF CHANNEL on the VCR lightly.
2Turn on your TV and select a vacant programme position.
3Tune the TV to the display window’s RF channel to show the
message below. Refer to your TV’s instruction manual for
tuning instructions.
4Press RF CHANNEL.
If your TV has a Scart (EURO-AV) connector.
1Press RF CHANNEL on the VCR lightly.
2Press PROGRAM +/– to set the RF channel to off.
3Press RF CHANNEL.
Now you can operate your VCR.
For details on how to use your VCR, refer to the Operating
Instructions.
You can enter your personal code to mark your new VCR for
identification. See “Setting your personal code.”
Setting your personal code
For security, you can enter a personal code (up to eleven
characters), such as your post code. If your VCR is stolen and then
recovered, you can identify your VCR using your personal code.
Once you enter the code, you can never change it. Please make a
note of the code to quote to the police if your VCR is stolen.
Before you start...
• Turn on your TV and set the TV to the video channel.
• IfthereisatapeintheVCR,removeit.
•TurnofftheVCR.
RF CHANNEL
PROGRAM +/–
SONY VIDEO CASSETTE RECORDER
1Hold down X(pause) and
I/1(on/standby) on the
VCR simultaneously for
three seconds.
2Enter your personal code.
1Press M/mto select a character.
A t B t ... t Z t 0 t 1 t ... t 9 t (blank space) t
– (hyphen) t A
2Press ,to set the next character.
3Repeat steps 1 and 2 until you have entered the entire
personal code.
3Press OK.
4If the displayed personal code is correct, press OK.
If not, press CLEAR and repeat from step 2.
123
456
789
0
I/1
X
CLEAR
M/m/</,
OK
MENUEXIT :
SECURITY FUNCTION
–
PERSONAL CODE
––––––– –
CONFIRM :
SET : OK
SELECT :
––
MENUEXIT :
SECURITY FUNCTION
–
PERSONAL CODE
WB–1578 –––
CANCEL : CLEAR
FINAL CONFIRM OK: