Sound Storm SX-200 User manual

1.
FEATURES SPECIFICATIONS
1. Find a suitable location in the vehicle to mount the crossover.
2. Bolt the crossover to the mounting surface.
3. Using the screw terminals provided, connect minimum 16 gauge wire from the power,
ground and remote terminals. Connect the shortest possible wire to a chassis ground point. The (+)12V connection
should be made directly to the car battery, and the remote should be connected to the Remote Turn On Lead of your
head unit. When connecting directly to the battery, install a 3A Fuse within 18 inches of the battery terminal.
4. Connect all line inputs and outputs using high-quality RCA cables.
5. Recheck all connections before powering up.
6. Set all level controls to their minimum positions and set all crossover controls, switches, etc. to the desired
frequency or position.
7. Once the system is powered up, set the volume control on thehead unit to a moderate level where
your normal speaking voice can be heard while the music is playing.
8. Further fine tuning of the various controls may be necessary to obtain the desired results.
9. When unsure about installation or system tuning, please consult an authorized SOUND STORM dealer.
INSTALLATION
2.
HIGH PASS CHANNEL :
High Pass Frequency Selector 50Hz to 1.5KHz
High Pass Output Level Control
SUBWOOFER CHANNEL
Low Pass Frequency Selector 35Hz to 400Hz
+12dB Bass Boost
Phase Shift Switch
Stereo/Mono Switch
Output Level Control
Exclusive Remote Subwoofer Level Control
Power Supply .................. DC to DC switching power
S/N Ratio ......................... 110dB
Channel Separation......... 80dB
Distortion ......................... THD @ 0.01%
Crossover Slope ............. 12dB per Octave
Input Impedance ............. 20K Ohms
Output Impedance .......... 100 Ohms
Output Gain .................... 1:2 (+6dB)
Output Voltage Level ....... 8Volts Max
Features and specifications subject to change without notice.
15
3
2
4
6
7
8
9
10
11
13
12
14
CONTROLS AND OPERATION
1. Low Level Input jacks.
1. Subwoofer Low Pass Frequency Selector: By turning the selector you can choose
from an infinite number of crossover points from 35Hz to 400Hz.
2. Bass Boost Control (45Hz): You can increase the bass level up to +12dB.
3. Phase Shift Selector Switch: Use this switch to select Output Phase for the Subwoofer
Channel to provide best time alignment and stereo imaging.
4. High Pass Frequency Selector: By turning the selector you can choose from an
infinite number of crossover points from 50Hz to1.5KHz.
5. Subwoofer Output Level Control: By turning this control clockwise you can increase
Low pass output gain.
6. Stereo/Mono Switch: For selection of stereo or mono mode for Subwoofer Output Signal.
7. High Pass Output Level Control: By turning this control clockwise you can increase
the High pass output gain.
8. LED Power On Indicator.
9. Signal Input Connectors
10. Low Pass (Sub-Woofer) Output Connectors
11. High Pass Output Connectors
12. Power Connections Terminal: +12V, Ground and Remote Turn-On
+
BATTERY
B+ 12V
REM GND
RED
ORANGE
BLACK
ELECTRONIC CONNECTIONS &WIRING
WIRING DIAGRAM: Signal Connection
This is typical 2-way connection.
In this mode the output signal will be devided into two:
LOW PASS and HIGH PASS output terminals.
Connect HIGH PASS output to an amplifier for composite signal of HIGH range
and connect LOW PASS output to LOW (SUB-WOOFER) amplifier.
Refer to the following illustration.
CAR STEREO
POWER AMPLIFIER
*MID-BASS
*MIDRANGE
*TWEETER
SUB-WOOFER
POWER AMPLIFIER
Congratulations on your purchase of a SOUND STORM Electronic Crossover. This product has been designed
and built to deliver excellent sound quality and long lasting high performance. We are sure you'll enjoy listening
to your favorite music with this SOUND STORM component in your car audio system. For best results please
consult a professional car stereo installer for application advice or troubleshooting. Thank you for choosing
SOUND STORM products for your
INTRODUCTION
autosound system. Everything else is just noise.
Dimensions ..................... 7-5/16"(W) x 7 5/16"(L) x 1-5/8"(H)