Sound Tube IPD-SM-EZ Series Configuration guide

Box contents
© 2019 SoundTube Entertainment, Inc. All rights reserved. PN IPD-INS-SM-EZ Rev 07-11-2019
Install Instructions For:
IPD-SM52-EZ and IPD-SM82-EZ
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
U-bracket
Back plate
IPD-SM-EZ Series
1.435.647.9555 | 800.647.TUBE | www.soundtube.com
Safety cable
U-bracket screw
Screw cap
Warning
1 Speaker
1 U-bracket
2 U-bracket screws
2 Screw caps
1 Allen wrench
1 Back plate
1 Port plug
1 Safety cable
1 Strain relief water tight gland
Strain relief water tight gland

Pour réduire les risques d’incendie ou de choc électrique n’exposez
pas cet appareil à la pluie ou à l’humidité.
Avis
To reduce the risk of re or electric shock, do not expose this
apparatus to rain or moisture.
Warning
Install Instructions For:
IPD-SM52-EZ and IPD-SM82-EZ
IPD-SM-EZ Series
Important Safety Instructions

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9) Only use the attachments/accessories specied by the manufacturer.
10) Unplug this apparatus during lightning storms or when unused for long periods of time.
11) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Consignes de sécurité importantes

1) Lisez ces instructions.
2) Conservez ces instructions.
3) Respectez tous les avertissements.
4) Suivez toutes les instructions.
6) Nettoyer seulement avec un chiffon sec.
7) Ne pas bloquer les ouvertures de ventilation. Installer conformément aux instructions du fabricant.
8) Ne pas installer près de sources de chaleur telles que des radiateurs, registres de chaleur, poêles ou autres
appareils (incluant les amplicateurs) qui produisent de la chaleur.
9) Utiliser uniquement les xations / accessoires spéciés par le fabricant.
10) Débranchez cet appareil pendant les orages ou si inutilisé pendant de longues périodes de temps.
11) Conez toute réparation à un personnel qualié. Une réparation est nécessaire lorsque l'appareil a été
endommagé de quelque façon que ce cordon d'alimentation ou la che est endommagé, l'appareil a été exposé à la
pluie ou à l'humidité, s'il ne fonctionne pas normalement ou s'il est tombé.

Port protection for SM-EZ
1. Unpack speaker and
mounting hardware.
2. Choose a secure mounting
surface with sufcient strength
to reliably hold the speaker.
The speaker may be mounted
in either the vertical or the
horizontal position with the
same U-bracket.
9. Aim speaker and tighten
u-bracket screws. Once
tightened down, place the
screw caps on the screws.
Done!
To enhance protection of
internal components from
humidity and other potentially
corrosive elements, use
provided port plug to seal
enclosure. Use RTV silicone
around edge of the port plug
for increased protection.
8. Tilt speaker 45º (grille up)
and slide on to bracket.
Install Instructions For:
IPD-SM52-EZ and IPD-SM82-EZ
IPD-SM-EZ Series
5. RJ-45 must be terminated
after CAT cable is run through
the water tight gland. Run
signal wire through the strain
relief gland and terminate RJ-45
connector. Once the connection
is secure, connect the signal wire
to the back of the speaker and
tighten the top of the wire gland
such that the rubber grommet is
tight around the cable. This may
require a wrench.
6. Install back plate and
secure with included fasteners.
7. Select desired location for
safety cable and remove the
U-bracket screw from that
side. Attach safety cable to the
clamping screw and reinstall
loosely.
3. Mount u-bracket with
clamping slots pointing
upward. Securely fasten
mounting bracket and safety
cable to surface (user must
supply fasteners).
Note: The safety cable will
attach to the U-bracket
clamping screw on one side of
the cabinet.
4. Place strain relief gland in
one of the knockouts on the
back plate and securly fasten
the gland nut on the other
side.