SoundCraft MINI STAGEBOX 32 Manual

MINI STAGEBOX 32
by HARMAN
®
User & Installation Guide

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
2
© Harman International Industries Ltd. 2013
All rights reserved. Parts of the design of this product may be protected by worldwide patents.
Part No. 5028913
Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject
to change without notice and does not represent a commitment on the part of the vendor. Soundcraft shall
not be liable for any loss or damage whatsoever arising from the use of information or any error contained in
this manual.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any
purpose without the express written permission of Soundcraft.
Harman International Industries Limited
Cranborne House, Cranborne Road, POTTERS BAR, Hertfordshire, EN6 3JN, UK
Tel: [phone]
Fax: [phone]
http://www.soundcraft.com
IMPORTANT
Please read this manual carefully before using
your unit for the rst time.
Warning: Any modication or changes made to this device, unless explicitly approved by Harman, will
invalidate the authorisation of this device. Operation of an unauthorised device is prohibited under
Section 302 of the Communications act of 1934, as amended, and Subpart 1 of Part 2 of Chapter 47
of the Code of Federal Regulations.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna
* Increase the separation between the equipment and the receiver
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help
For further details contact
Harman International Industries Ltd, Cranborne House, Cranborne Road, Potters Bar, Hertfordshire EN6 3JN, UK
Telephone [phone] Fax [phone] email: [email protected]
[email protected]
This equipment complies
with the EMC Directive
2004/108/EC and LVD
2006/95/EC
This equipment complies with the EMC directive 2004/108/EC
and LVD 2006/95/EC
This product is approved to safety standards
IEC 60065:2005 +A1:2005
EN60065:2006 +A1:2006 + A1:2008
UL60065 7th Edition
CAN/CSA-E60065-03 +A1:2006
And EMC standards
EN55103-1: 2009 (E2)
EN55103-2: 2009 (E2)
by HARMAN
®

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
3
CONTENTS
INTRODUCTION 4
SAFETY NOTICES 4
SAFETY SYMBOL GUIDE 4
IMPORTANT SAFETY WARNINGS 5
ELECTROSTATIC DISCHARGE (ESD) 6
IMPORTANT SAFETY INSTRUCTIONS 7
WORKING SAFELY WITH SOUND 8
FEATURES 9
MINI STAGEBOX FRONT PANEL 10
MINI STAGEBOX REAR PANEL 10
MOUNTING MINI STAGEBOX 11
MADI LINK CARD 11
CONNECTING IT UP 12
MINI STAGEBOX CONNECTING TO Vi2-Vi6 RANGE CONSOLES 12
MINI STAGEBOX CONNECTING TO Si OR Vi1 CONSOLES 13
MINI STAGEBOX CONNECTING TO TWO CONSOLES 14
SPECIFICATIONS 15
WARRANTY 16

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
4
INTRODUCTION
SAFETY NOTICES
FOR YOUR OWN SAFETY AND TO AVOID INVALIDATION OF THE WARRANTY
PLEASE READ THIS SECTION CAREFULLY.
SAFETY SYMBOL GUIDE
For your own safety and to avoid invalidation of the warranty all text marked
with these symbols should be read carefully.
WARNINGS
The lightning ash with arrowhead symbol, is intended to alert the
user to the presence of un-insulated “dangerous voltage” within
the product’s enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
CAUTIONS
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
NOTES
Contain important information and useful tips on the operation
of your equipment.
HEADPHONES SAFETY WARNING
Contain important information and useful tips on
headphone outputs and monitoring levels.
ESD WARNING
The crossed-out hand symbol is intended to alert the user to
devices sensitive to electrostatic discharge. Please refer to the
instructions on page 6.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
5
IMPORTANT SAFETY WARNINGS
THIS APPARATUS MUST BE EARTHED. Under no circumstances should the safety
earth be disconnected from the mains lead.
The mains supply disconnect device is the mains plug. It must remain accessible so as
to be readily operable when the apparatus is in use.
If any part of the mains cord set is damaged, the complete cord set should be
replaced. The following information is for reference only.
The wires in the mains lead are coloured in accordance with the following code:
Earth (Ground): Green and Yellow (US - Green/Yellow)
Neutral: Blue (US - White)
Live (Hot): Brown (US - Black)
As the colours of the wires in the mains lead may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal
in the plug which is marked with the letter E or by the earth symbol.
The wire which is coloured Blue must be connected to the terminal in the plug
which is marked with the letter N.
The wire which is coloured Brown must be connected to the terminal in the plug
which is marked with the letter L.
Ensure that these colour codes are followed carefully in the event of the plug being
changed.
This unit is capable of operating over a range of mains voltages as marked on the rear panel.
The internal power supply unit contains no user serviceable parts. Refer all servicing
to a qualied service engineer, through the appropriate Soundcraft dealer.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
6
ELECTROSTATIC DISCHARGE (ESD)
Many semiconductor components are sensitive to electrostatic discharge (ESD).
The lifespan of assemblies containing such components can be drastically reduced
by improper handling during maintenance and repair. Please observe the following
rules when handling ESD sensitive components:
• ESD sensitive components should only be stored and transported in the
packing material specically provided for this purpose.
• When performing a repair by replacing complete assemblies, the removed
assembly must be sent back to the supplier in the same packing material in
which the replacement assembly was shipped. If this should not be the case,
any claim for a possible refund will be null and void.
• Unpacked ESD sensitive components should only be handled in ESD protected
areas (EPA, e.g. area for eld service, repair or service bench) and only be
touched by persons wearing a wristlet connected to the ground potential of the
repair or service bench by a series resistor. The equipment to be repaired or
serviced as well as all tools and electrically semi-conducting work, storage, and
oor mats should also be connected to this ground potential.
• The terminals of ESD sensitive components must not come in uncontrolled
contact with electrostatically chargeable or metallic surfaces (voltage puncture,
discharge shock hazard).
• To prevent the components from undened transient stress and possible
damage due to inadmissible voltages or compensation currents, electrical
connections should only be established or separated when the equipment is
switched off and after any capacitor charges have decayed.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
7
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including ampliers) that produce heat.
Do not defeat the safety purpose of a polarised or grounding type plug. A polarised
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles and the point where they exit from the apparatus.
Only use attachments/accessories specied by the manufacturer.
Use only with the cart, stand, tripod, bracket or table specied by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of
time.
Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been
dropped.
NOTE: It is recommended that all maintenance and service on the product should
be carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any
liability whatsoever for any loss or damage caused by service, maintenance or repair
by unauthorised personnel.
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus
to rain or moisture. Do not expose the apparatus to dripping or splashing and do not
place objects lled with liquids, such as vases, on the apparatus. No naked ame
sources, such as lighted candles, should be placed on the apparatus.
Ventilation should not be impeded by covering the ventilation openings with items
such as newspapers, table cloths, curtains etc.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
8
WORKING SAFELY WITH SOUND
Although your new unit will not make any noise until you feed it signals, it has
the capability to produce sounds which when monitored through a PA system or
headphones can damage hearing over time.
The table below is taken from the Occupational Safety & Health Administration
directive on occupational noise exposure (1926.52):
PERMISSIBLE NOISE EXPOSURE
DURATION PER DAY,
HOURS
SOUND LEVEL dBA
SLOW RESPONSE
8 90
6 92
4 95
3 97
2 100
1.5 102
1 105
0.5 110
<0.25 115
Conforming to this directive will minimise the risk of hearing damage caused by
long listening periods. A simple rule to follow is — the longer you listen, the lower
the average volume should be.
Please take care when working with your audio. If you are manipulating controls
which you don’t understand (which we all do when we are learning), make sure your
monitors are turned down. Remember that your ears are the most important tool of
your trade, look after them, and they will look after you.
Most importantly — don’t be afraid to experiment to nd out how each parameter
affects the sound — this will extend your creativity and help you to get the best
results.
Recommended headphone impedance is 50-600 ohms.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
9
FEATURES
The Mini Stagebox 32 is ideal for for expanding the I/O capabilities of any of the Vi
or Si range of consoles regardless of whether that I/O is needed locally or hundreds
of metres away on the stage.
The Soundcraft Mini Stagebox 32 requires only 3U of rack space and, in this tiny
footprint, provides 32 recallable mic/line inputs, 8 balanced line outputs and 4
pairs of AES outputs, all lifted directly from the Vi1 and larger Compact Stagebox.
The Mini Stagebox 32 is connected to the host console using either Cat-5 or
optical-bre MADI, the same way as the larger 64 mic/line Vi6 Stagebox is hooked
up, and shares the same redundant MADI cable capability when connected directly
to a single console. The efcient design negates the need for a fan so making the
MINI Stagebox ideal for applications where silence is a must!
Expansion Slots
On the rear of the Mini Stagebox 32 are two blank panels reserved for future
expansion.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
10
1. MIC/LINE IN 1-16 - CARD A
2. MIC LINE IN 17-32 - CARD C
3. LINE OUT 1-8 - CARD I
4. AES OUT 1-8
5. MADI CARD (OPTICAL OR CAT5)
6. POWER INDICATOR
MINI STAGEBOX 32 FRONT PANEL
1. AC INLET AND POWER SWITCH
MINI STAGEBOX 32 REAR PANEL
6
5
4
1
1
2
3

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
11
MOUNTING MINI STAGEBOX 32
When installed in a 19" rack mount ensure all four mounting holes are used.
If mounted with other equipment that may get hot (~power requirement of
‘other’ equipment >100W) it is recommended to leave a 1U gap between the
equipment.
In all scenarios, the air vents must not be obstructed and the Mini
Stagebox32 must not be mounted in a fully sealed enclosure.
MADI LINK CARD
This card provides the audio and control connections to the console through
either a Cat-5 or an Optical-bre MADI link. The corresponding MADI card
in the console transmits the clock for the Mini Stagebox 32 down the MADI
stream.
The second (AUX) connector on the card can be used to provide a redundant
connection to the console,
The MADI HD card indicates its clock status with the ‘LOCK’ LED on the card.
It is possible to connect two different consoles to the MAIN and AUX
ports, and provide a split of the mic inputs to the two consoles. However,
be aware when using the Cat5 version that the console which has control
of the preamp gains, and is able to send signals to the Mini Stagebox
(MSB) 32 outputs, will be the rst active console to be connected to the
MSB or the rst console to be switched on if both are already connected.
This means that the gain control and output routing can switch from
one console to the other, depending on power-up order or connection
sequence. Consequently we do not recommend operation with two
consoles with the Cat5 version.
With the optical version, this situation can be avoided by leaving the
MADI IN optical port unconnected on whichever port (MAIN or AUX) that
the 'slave' console is connected to. (See hook-up diagram on page 14).

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
12
CONNECTING IT UP
MINI Stagebox Connecting to Vi2-Vi6 Range Consoles
Note: Connections from the local rack to the Mini Stagebox 32 may vary depending
on actual ightcase and breakout panel options.
MINI Stagebox 32
Optical or RJ45 Cables
depending on MADI card type
Local Rack
See notes regarding setup of
MADI HD Card on page 11

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
13
MINI STAGEBOX 32 CONNECTING TO Si OR Vi1 CONSOLES
• Connections from the console to the MINI Stagebox may vary depending on actual
ightcase and breakout panel options.
• For Si1, 2 and 3 consoles, including their ‘PLUS’ variants, read the Si Option Slot
and Option Card User Guide if using more than 1 option card in the console.
See notes regarding setup of
MADI Link Card on page 11
MINI Stagebox 32
Si Performer (Vi1 or other Si series) Console
with optional MADI card in the extension slot(s).
Optical or RJ45 Cables
depending on MADI card type

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
14
MINI STAGEBOX CONNECTING TO TWO CONSOLES
48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V 48V
48V48V48V48V48V48V48V48V48V 48V 48V 48V 48V 48V 48V 48V
32
PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH
PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH
‘MAIN’ console ‘AUX’ console
MINI Stagebox
Note: Optical MADI shown. Dual console setup is not possible with Cat version
due to the input and output being within the same 'AUX' Ethercon connector.
Do not connect MADI 'IN' on Aux port!
This console will control preamp gain and will
be able to access the Mini Stagebox outputs.

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
15
MINI STAGEBOX TYPICAL SPECIFICATIONS
Frequency Response
Mic / Line Input to any Output: +0/-1dB, 20Hz – 20kHz
T.H.D.
Mic Sensitivity -30dBu: < 0.01% @ 1kHz
Noise
Residual noise: -85dBu
Mic Input E.I.N. (maximum gain): -125dBu (150Ω source)
Mix noise, masters at unity: < -86dBu
1 input to mix at unity gain: -84dBu
CMRR mic @1KHz (max gain): -86dBu
Crosstalk (@ 1kHz)
Mic – Mic: <-80dB @ 1kHz
Input Gain
Mic Gain: -5dB – 58dB integrated pad design 1dB steps
Max. input level: +24dBu
Max. output level: +22dBu
Sample rate: 48kHz
Convertor resolution: 24 bit
Latency: 1.5ms
Internal clock accuracy: +/- 25ppm
Mains power consumption: 33W
Mains voltage operating range: 90 — 264 VAC, 47 — 63Hz
Operating temperature range: -10oC — +50oC
Relative humidity: 0 — 90%
Storage temperature range: -10oC — +50oC

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
16
WARRANTY
1 Soundcraft is a trading division of Harman International Industries Ltd.
End User means the person who rst puts the equipment into regular operation.
Dealer means the person other than Soundcraft (if any) from whom the End User purchased the Equipment,
provided such a person is authorised for this purpose by Soundcraft or its accredited Distributor.
Equipment means the equipment supplied with this manual.
2 If within the period of twelve months from the date of delivery of the Equipment to the End User it shall prove
defective by reason only of faulty materials and/or workmanship to such an extent that the effectiveness
and/or usability thereof is materially affected the Equipment or the defective component should be returned
to the Dealer or to Soundcraft and subject to the following conditions the Dealer or Soundcraft will repair
or replace the defective components. Any components replaced will become the property of Soundcraft.
3 Any Equipment or component returned will be at the risk of the End User whilst in transit (both to and from
the Dealer or Soundcraft) and postage must be prepaid.
4 This warranty shall only be valid if:
a) the Equipment has been properly installed in accordance with instructions contained in Soundcraft’s
manual; and
b) the End User has notied Soundcraft or the Dealer within 14 days of the defect appearing; and
c) no persons other than authorised representatives of Soundcraft or the Dealer have effected any
replacement of parts, maintenance adjustments or repairs to the Equipment; and
d) the End User has used the Equipment only for such purposes as Soundcraft recommends, with
only such operating supplies as meet Soundcraft’s specications and otherwise in all respects in
accordance with Soundcraft’s recommendations.
5 Defects arising as a result of the following are not covered by this Warranty: faulty or negligent handling,
chemical or electro-chemical or electrical inuences, accidental damage, Acts of God, neglect, deciency
in electrical power, air-conditioning or humidity control.
6 The benet of this Warranty may not be assigned by the End User.
7 End Users who are consumers should note their rights under this Warranty are in addition to and do not
affect any other rights to which they may be entitled against the seller of the Equipment.
PRODUCTS UNDER WARRANTY
UK customers should contact their local dealer.
Customers outside the UK are requested to contact their territorial distributor who is able to offer support in the
local time zone and language. Please see the distributor listings on our website (www.soundcraft.com) to locate your
local distributor.
OUT-OF-WARRANTY PRODUCTS
For out-of-warranty consoles purchased in the United Kingdom, please contact the Customer Services Department
(e-mail: [email protected]) at the factory in Potters Bar, Hertfordshire: Telephone [phone].
For all other out-of-warranty consoles, please contact the appropriate territorial distributor.
When mailing or faxing please remember to give as much information as possible. This should include your name,
address and a daytime telephone number. Should you experience any difculty please contact Customer Services
Department (e-mail: [e-mail]).

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
17

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
18

Soundcraft Mini Stagebox 32 User/Installation Guide 0813
19

by HARMAN
®
Soundcraft
Harman International Industries Ltd
Cranborne House
Cranborne Road
Potters Bar
Herts. EN6 3JN
United Kingdom
[phone]
www.soundcraft.com