Soundstream VR-345 User manual

VR-345/VR-345T
VR-345B /VR-345BT
Flip-down/Detachable 3.4" Monitor
DVD/CD/MP3/MP4 Player
AM/FMRadio
Built-in TV tuner( only for VR-345T NR-345BTmodel)
Support Bluetooth (only for VR-345B NR-345BTmodel)
Owner's Manual
Take the time to read through this owner's manual.
Familiarity with installation and operation procedures will help you obtain the best
Performance from your new DVD-receiver.

• Using the device at temperature below
-1
0
OC
may cause the breakage
of
the device.
BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE
RECOMMENDED TEMPERATURE!
• Read carefully through this manual to familiarize you with this high-quality sound
system.
• Disconnect the vehicle's negative battery terminal while mounting and connecting the
unit.
• When replacing the fuse, be sure to use one with an identical amperage rating. Using a
fuse with a higher amperage rating may cause serious damage to the unit.
• DO
NOT
attempt to disassemble the unit. Laser beams from the optical pickup are
dangerous·to the eyes.
• Make sure that pins or other foreign objects do not get inside the unit; they may cause
malfunctions, or create safety hazards such as electrical shock or laser beam exposure.
• If you have parked the car for a long time
in
hot
or
cold weather, wait until the
temperature
in
the car becomes normal before operating the unit.
• DO NOT open covers and do not repair yourself. Consult the dealer or an experienced
technician for help.
• Make sure you disconnect the power supply and aerial if you will not use the system for
a long period
or
during a thunderstorm.
• Make sure you disconnect the power supply ifthe system appears to be working
incorrectly, (For example: making unusual sounds, smelling strange, emitting smokes
from inside or liquid having gotten inside
it)
Have a qualified technician check the
system.
• The unit is designed for negative terminal
of
the battery, which is connected to the
vehicle metal. Please confirm it before installation.
• Do not allow the speaker wires to be shorted together when the unit is switched on.
Otherwise it may overload
or
burn out the power amplifier.
• Do not install the detachable panel before connecting the wire.
• Don't remove the detachable panel when encoding.
2

------------------------------.~~~
rr:m:mmmm
Important Safeguards...............................................................................................................2
Contenents...............................................................................................................................3
Accessories..............................................................................................................................4
lnstallation/Un-lnstallation........................................................................................................5
Wiring Connections..................................................................................................................6
Front Panel ..............................................................................................................................7
Inner Panel...............................................................................................................................
?
Remote Control........................................................................................................................8
Remove Battery .....................................................................................................................10
Main Menu .............................................................................................................................
11
General Operation ................................................................................................................. 11
Radio Operation.....................................................................................................................15
DVD/USB/SD/MMC Operation...............................................................................................16
TV Operations(Only for VR-345T NR-345BTmodel) .............................................................19
Bluetooth Section(Only for VR-3458
NR-345BTmodel) ........................................................20
Anti-theft System....................................................................................................................
21
Handling &Cleaning DISC..................................................................................................... 21
Troubleshooting Guide.....·......................................................................................................23
Specification...........................................................................................................................24
3

Packa e contains the followin accessories for installation and o eration
of
the unit.
(1) Washer, Spring
Washer, M5 Nut
(2) Mounting Strap
(3) Bolt 5*20
(4) Screw 5*6
1 each
1
1
4
(5) Mounting Collar 1
(6) Release Key 2
(7) Screw 5*20 . 1
(8) Rubber Cushion 1
User
Manual
User Manual
Note:
~
o o
c::.>
o o
o)
::=::-#::._,..
1x front panel protection case
Warranty card
II
II
Trim ring Power cable
Product image may vary from the actual delivery.
4

-
First complete the electrical connections, and then check them for correctness.
Installation
This unit can be installed
in
any
dashboard having an opening as
shown on the picture. The
dashboard should be
4.
75 -5.56
mm thick
in
order to be
abl.e
to
support the unit.
1.
Insert mounting collar into the
dashboard, and bend the
mounting tabs out with a
screwdriver.
Make sure that lock lever C
*)
is
flush with the mounting collar (not
projecting outward).
2.
Secure the rear
of
the unit.
Lock lever ( *
)
After fixing mounting bolt and power connector, fix the rear
of
the unit to the car body by rubber
cushion.
3.
Insert trim plate.
When you prepare to insert trim plate, please check its direction. Once it was up side down, it
cannot be fixed. .
Un-installation
Remove Trim Ring and insert Release Keys into left and
~
right side-end holes as shown
in
below picture and
puiiQ
...
the unit out
of
the dashboard.
5

-
---------~~~~~~'\),
....
Make sure you have good chassis ground. A good ground connection will eliminate most
electrical noise problems. A good chassis ground requires a tight connection to the vehicle's
metal chassis. The area around the ground connection should be clean, bare metal without rust,
paint, plastic, dust,
or dirt for a good electrical connection.
Caution: Do not interchange
the connection
of the wiring!!l
For some car models you
may need to modify wiring
of
the supplied power cord.
Contact your authorized car
dealer before installing this
unit.
Using the ISO Connector
1. Ifyour car is equipped with
the ISO connector, then
connect the ISO connectors
as illustrated.
2. For connections without
the ISO connectors, check
the wiring
in the vehicle
carefully before connecting,
incorrect connection may
cause serious damage to this
unit.
3. Cut the connector;
Connections:
A1 BATTERY +12VDC -+To terminal
always supplied with power
A2 ACC +12VDC -+To electric terminal
controlled by ignition switch (12VDC)
ON/OFF
A7 Parking
A8 Revene
A13 REMDTE/PWR.ANT +12VOC-To
system control terminal of the
power amp or Auto-antenna control
terminal
A14 Ground-To vehicle (metal! body
C~tmar• in
Lmeo1.1t (FR!
Une out !RAJ
L•ne out {All
lmi!Ot,~t{fl)
V•deo OUT
Front Speaker
A 4 Left+ (white)
A 11 Left· (white/black)
A 5 Right+ {gray)
A10 Right- (gray/black)
Rear Speaker
A 3 Left+ (green)
A12 left· (green/black)
A 8 Right+ (purple)
A 9 Right· (purple/black}
~- ~ -- ''ey'
ffi "'''~''' ww.. ~~~ AIIIII A ~ A
~ l"'!t~-,.~ :1hfl- ---· -
connect the colored leads of
the power cord to the car
battery as shown
in the color
code table below for speaker
and power cable connections.
----------------------------------------------------
Function
Connector A Connector B
Rear Right(+)---Purple
Camera (12V DC)--Pink Rear Right(-)---Purple/Black Stripe
Parking (GND)--Brown Front Right(+)---Grey
Battery 12V (+)--Yell
ow
Front Right(-)---Grey/Black Stripe
Auto Antenna--Blue Front Left(+)---White
Front Left(-)---White/Black Stripe
ACC(+)--Red Rear Left(+)---Green
Ground--Black Rear Left(-)---Green/Black Stripe
6

Front panel
5 6 7
8 9
23
10
14
15
-
16
-
17
I
11
12
13
1)
2)
3)
4)
5)
6)
7)
8)
9)
Power /Mute button
EQ /LOUD button
SEL button
1
0)
Play/Pause, Memory /Reject button
Mode button
SCAN button
MENU button
Volume/OK button
AS/PS button
BAND
I
Media select /Accept button
Inner panel
1~
19
20
21
22
L
___,
[
s~(
)K
0
~CJ~
lMI(>
0
@
[~
~B
18)
SD/MMC card slot
19)
Eject button
20)
Disc loading slot
21
)
Anti-Theft LED flash
22)
Reset button (hole)
23)
MIC
11
) Previous
I
Reverse button
12)
Next
I
Forward button
13)
IR sensor
14)
LCD Screen
15)
OPEN button
16)
USB slot
17)
AV
IN
jack
L__j
Jl
rn[Jm
0
c=J
3
0 0
B
@~
0
NOTE: When turn
off
the power, the unit will switch to standby mode unless cut the ACC power.
The power light will continue lighting. ·
7

------------
..
~
...............
~
~
'i%t
,,
~
1.
POWER
Power on or off.
2.
MODE button
1
Power
ON/OFF
2 MODE
5
BAND/ROM
Clear(Only
for
BT)
6
UP
Arrow
9
Left
Arrow
10
Enter
13
Eject
14
Down
Arrow
17
P.
SCAN/RPT
#(Only
for
BT)
18
ST/MO
PTY(Only
for
RDS)
*lOnly
for
BT)
21
LOUD
TA(Only
for
ROS)
22
SEEK-/
...
25
STOP/PBC
260SO
29
Number
Key
Note:
1 AF
just
for
RDS
model
3
Play/Pause
4
Mute/Biuetooth
7
MENU
8
Sub-t
11
Right
Arrow
12
Setup
15
Angle
,......(Only
for
BT)
16
INT
~(Only
for
BT)
19
VOL+
20
ZOOM/A-8
23SEL
AF(Only
for
RDS)
24SEEK+/
...
27
VOL-
28
AUDIO/GO
TO
30
OPEN/TILT
(Optional)
31
DUAL(Optional)
2
TA/PTY
for
RBDS/RDS
model
3
* # ...,....
~
Bluetooth
These
Functions
for
Bluetooth
Models
4 EJECT
OPEN/TILT
DUAL
Optional
function
Press it to select the mode: Radio, DISC (if there is a disc
in
unit), USB (if there is a USB device
in
the unit), CARD (ifthere is a SD/MMC card
in
the unit), TV (for TV model) and
AV
IN.
3.
PLAY/PAUSE button
In
DVD mode, press it to pause playback, press again to resume.
4.
Mute button
~:Short
press this button to mute the volume output, press it again to resume volume.
5.
BAND/
ROM
(Only
for
BT)
In
Radio mode, press to change radio band
in
sequence
of
FM1
-----+
FM2-----+
FM3
~
AM1
~
AM2
In
DVD mode,press to play randomly.
6.
Cursor
6
buttons
Use the t buttons to select the menu item. The title, track or to show next frame.
7.
MENU button
Press it to show main menu,
in
DVD mode, long press it to enter TITLE MENU (Enable only ifthe
DVD disc with title menu).
8.
SUBTITLE button
Press it to select the subtitle language (Available only ifthe disc with subtitle function).
9.
Cursor • buttons
Use the • buttons to select the menu item. the title, track or to show next frame.
10. ENTER button
Press it to confirm selection or setting.
8

11.
Cursor
•buttons
Use the • buttons to select the menu item. The title, track or to show next frame.
12. SETUP
button
In
DVD mode press it to enter the setup menu.
13. EJECT
button
Press it to eject the disc.
14.
Cursor
f
buttons
Use the
f
buttons to select the menu item. the title, track or to show next frame.
15. ANGLE
button
(Only
for
BT)
In
DVD mode, press it repeatedly to change the viewing angle (Available only with a recorded
DVD file or DVD disc that has this function).
16. INT
button
(Only
for
BT)
Press it to activate the intra function. You can play the beginning of every track for
10
seconds
in
sequence.
17. P.SCN/ RPT
In
SO
CARD/ USB mode, press to repeat REP 1 => REP DIR
=>
REP ALL
In
DVD mode, press to start repeat REP OFF=>REP Chapter=>REP Title=>REP Off.
In
Radio mode:
PS
(Preset Scan): Press to scan all preset stations
in
the memory
of
the current
band and stay
on
each memory stations for about 5 seconds.
AS (Auto Save): Long press to save the stations with good reception automatically.
18. STEREO/MONO (PTY
only
for
BT)
Press STEREO button to select STEREO or MONO.
19. VOL+
button
Press
to
increase volume level.
20.
A-8/ZOOM
button
During playback, press it at the starting point
of
section you want to repeat(A), press this button
again at the ending point
of
the section you want to repeat (8), section
A-8
repeating starts.
Press it again to cancel the A-8 repeat function.
Press it and hold for two seconds
in
DVD mode to zoom the image
in
or out
in
the sequence
of
ZOOM 2-> ZOOM 3-> ZOOM 4-> ZOOM 1/2-> ZOOM 1/3-> ZOOM 1/4.
21. LOUD
Press to set LOUD
on
or OFF.
22.
,,.
..
I
seek-
button
In
DVD mode, Press
~
....
button to skip to the previous track. Press and hold
,,.
..
button for two
seconds to activate fast reverse (REW) search
in
a track.
In
RADIO mode, press ,
....
button to start searching automatic, press and hold for two seconds to
start manual searching. ,
....
button Frequency down.
23. SEL
button
Press it to enter the SOUND SETTING menu, and press Cursor UP/ON buttons to choose
an
item and press cursor lefUright buttons to set the item. Press SEL button again to exit the menu.
24.
..,..,,
I
seek
+
button
In
DVD mode, Press
...
~
button to skip to the next track. Press and hold
..,..,,
button for two
seconds to activate fast forward (FF) search
in
a track.
In
RADIO mode, press
..,.,,
button to startsearching automatic, press and hold for two seconds to
start manual searching
..,..,,
button Frequency
up.
25. STOP/PBC
button
Press it to Stop playback from the current position, press it again to final stop to the very
beginning. Press PLAY/PAUSE button to play.
Press and hold for two seconds to set PBC on/ off
in
VCD mode.
9

utton
In
DVD mode press it to enter the OSD menu, press and hold for 2 seconds to set video setup.
(RED /GREEN /BLUE /BRIGHT
I
CONTRAST /SHARP /COLOR RESET /BACK)
27. VOL- button
Press to decrease volume level.
28. AUDIO/GOTO button
In
DVD mode press itto select the audio language.
In
VCD mode, press it to select the sound track
in
the sequence
of
MONO L =>MONO R
=>STEREO.
Go to:
in
DVD mode, press and hold for2 seconds to showTIME SEARCH menu, select number
and confirm to go to certain position directly. When
press•
button to enter TITLE/CHAPTER
selection mode, select numberand confirm to go to certain TITLE
or
CHAPTER position directly.
29. Digit 0-9 buttons
In
radio mode, select 1-6 the desired band;
In
DVD mode, select track.
30. OPEN/TILT button (Option without function)
31. DUAL button (Option without function)
Noted: The
RC
is the universal and full-featured. Some options are available with the
corresponding model.
Remove battery
Note:
• The distance may vary according to the brightness
of
ambient light.
• Ifthe remote is not used for an extended period
of
time, remove the battery to prevent
possible damage from battery leakage and corrosion.
• Do not place any objects between the remote
control unit and the sensor on the unit. l
~
• Do not drop the remote control onto the floor; it
will damage it beyond repair.
• Do not use the remote control unit, while
simultaneously operating the remote control
unit
of
any other equipment; they may interfere
resulting
in
improper operation.
• The battery normally last for about one year although depending how often the remote
control is used.
If
the remote control unit isn't working even when it is operated near the unit,
replace the battery with a new battery
of
the same make and use only a lithium cell battery
type: CR2025 (3V).
• Dispose empty batteries
in
accordance with your local governmental regulations.
• Do not short-circuit, disassemble, heat ordispose
of
fire orflames the battery.
• Keep the battery out
of
reach
of
children, should the battery be swallowed, immediately
consult a doctor.
10

~!~!! .................... ~ ~ ~
The best way to discover the program is to explore each screen in detail, and to find out how to
move from one to another. Read this chapter for a guided tour.
Unit starts by displaying the Main menu. can simply take knowledge
of the features.
General Operation
Reset the unit
Operating the unit for the first time or after replacing the car battery, you must reset the unit.
Press OPEN button on the panel to open the panel and press RESET button to restore the unit
to its original factory settings.
Power on or off
Press any button (except open button) to turn on the unit.
Long press POWER button on front panel
or press power button on the RC to power offthe unit..
Mode setting
Press the MODE button repeatedly to switch between inputs:
L RADIO-DISC* -USB* -SO* -Biuetooth* -TV -AV IN -RADI~
(*available only ifthere is media device in disc, SO, USB slot and Bluetooth connection is OK .)
Volume/OK
Adjust the volume level by turning the VOL knob on the panel clockwise to increase or
counterclockwise to decrease or pressing VOL+ or NOL- on the RC to increase or decrease the
volume.
In any mode, rotate VOL knob to select the file you want to playback, press the OK button to
enter the next menu.
Sound Adjustments
Press the SEL button on the RC or front panel to select the audio settings consisting of following
items:
EQ : Select the digital sound effect FLAT- CLASSIC-POP-ROCK -USER.
BASS: Bass up/down.
TREBLE: Treble up/down.
BALANCE: Left/right Balance control.
FADER: FronUrear Fader control.
BEEP: Keypad sound setting.
11

LOUDNESS: Set the loudness on or off.
Rotate Volume knob on the front panel
or press up/down arrow on the RC to select any items
and then press OK button on the panel
or Enter button on the RC to confirm the item.
Rotate Volume knob
or press LEFT/RIGHT buttons on the RC to adjust the audio setting. Press
OK button on the panel or Enter button on the RC to confirm and again press SEL button return
to current mode.
Note:
{-- If the unit is turned off, all the settings of each mode will be saved.
{-- If cutting off battery power or resetting the unit, all the settings will return to factory default
settings.
{-- When EQ is set to any mode (except USER mode), Bass and Treble are not adjustable.
Mute function
Press POWER/MUTE button on the panel or MUTE button on the RC to turn the sound off. Press
it again to resume the volume.
Loudness
Press LOUD button on RC or long press the LOUD button on the front panel to set loudness or
off.
EQ
Short press the EQ button on the panel to choose sound effect in the sequence of FLAT-
CLASSIC-POP-ROCK-EO OFF.
Menu
Press Menu button to show main menu. In DVD mode press and hold for two seconds to enter
title menu (Enable only ifthe DVD disc with title menu).
Setup
Press SETUP button on the RC or SETIING icon on the main menu to go to setup pages.
1) Rotate Volume knob on the front panel
or press up/down arrow on the RC to select any items
and then press OK button on the panel
or Enter button on the RC to confirm the item
2) Rotate Volume knob
or press LEFT/RIGHT buttons on the RC to adjust the audio setting.
Press
OK button on the panel or Enter button on the RC to confirm.
3 ) Press SETUP button again return to current mode.
Sound
EQ: select the digital sound effect.
BASS: bass up/down.
Treble: treble up/down.
Balance: LefVright Balance control.
FADER: Front/rear Fader control.
BEEP: Select keypad sound on
or off.
LONDNESS: Selecting loudness ON will
emphasize the low frequency output.
12

Display
General
Radio
DVD
[1 ].Subtitle Lang setting:
Screen: screen ratio control
Backlight: set the LCD screen backlight.
Dual: dual function control(if you need)
Key: current/DVD(ifyou need)
Clock setting: Press number buttons
to input
the current time.
Auto connect: set Bluetooth automatically
connect to previous paired device
or not (only
for
VR-345BN ,- .... -p .... LJ
Area: Select radio broadcasting area.
Stereo: Select ON (stereo reception mode)
or
OFF (mono reception).
With this option you can select the preferred language for the subtitles. When the selected
language is recorded on the disc then this language will automatically be shown. If not, the first
language recorded on the disc is displayed.
[2].Audio Lang setting:
13

-----------------.~~
~
~
~
With this option you can select the preferred language
for
the audio output. When the selected
language is recorded on the disc (not all discs have multiple languages recorded) then this
language will automatically be played.
If
not, the first language recorded on the disc is displayed.
[3]. DVD Menu Lang setting:
With this option you can select the preferred language for the disc menu. When the selected
language is recorded on the disc then this language will automatically be selected. If not, the first
language recorded on the disc is displayed.
[4]PASSWORD:
The password for this unit is initially set to factory default 0000. If you want to change your
password, you need to enter the old password first and confirm it, and enter a new password and
confirm. WARNING:
if
you forget your password, there is no possibility to reset the password
again. Do not forget your mask and write it down
or
store the mask
in
a safe place.
[5] Rating
I
PARENTAL SETUP.
For DVD discs which support the
USA
rating system, setting up rating control can prevent
children from watching content that might not be suitable for their age. You are asked to enterthe
password when you change the rating setting. The default password is 0000.
Code Description
1.NONE Kid safe
2.G General
Audiences-
ALL
ages admitted
3.PG PARENTAL GUIDANCE SUGGESTED-Some material may not be suitable for
children
4.PG-13 PARENTS
STRONGLY
CAUTIONED-Some material may be inappropriate
for children under 13
S.PG-R Restricted, under 17 requires accompanying parent
or
adult guardian.
6.R RESTRICTED-Under 17 requires accompanying_ parent
or
adult guardian
7.NC-17 NO ONE 17 AND UNDER ADMITTED
8.
Adult Above 17 Admitted
[6]
TV
TYPE:
Set
TFT
screen mode to the correct ratio:
Three screen ratio modes are available, Normai/PS (4:3 Pan Scan), Normai/LB (4:3 Letterbox)
and Wide (16:9). Different disc formats will display different images depending this setting and
the screen size used.
[7] NTSC/ PAL:
Select this menu item to set up your preferred video output format. PAL is commonly used in
Europe, NTSC is commonly used in the
USA
and Japan.
[8] DEFAULT:
Factory reset. Set all values to Factory default values including memory and preset stations
14

............................
~~
~
~
System
information
AVIN
The software version is just for your
r'eference.
Connect an optional AV cable to your external AV device (such as a video camera), then press
the MODE button to switch to the AV mode. Note: If there is no external video input, the TFT
displays "NO SIGNAL".
Parking
When the car is stopped and the parking brake
is
working, the screen can display the video .
image, and otherwise the screen display warning information.
Back
view
camera
This unit is equipped with back view camera output. The camera is used to observe the situation
behind the vehicle when you are backing the car.
Please connect your back view camera with the back car video input. And connect the reverse
wire for back a car with the rear gear light. Rear view camera picture will
be
enabled when you
are backing the car.
'Radio operation
Band
selection
Press Band button on the
RC
or front panel to select your band
of
choice
in
the following
sequence:
FM
1 ---.
FM
2---.
FM
3---.
AM1
--.AM2
Manual
tuning
To find a station, select a band first, then press and hold
·~~
I
.,..,.,
buttons on the
RC
until
Manual appear on the display. Then press repeatedly these buttons to search for the needed
frequency upward or downward.
Auto
tuning
To find a station, select a band first, then press
•~~
I
......
,
buttons on the panel
or
press
·~~
I
.,..,.,
buttons on the
RC,
the automatic search will start downward or upward. It will stop when a
station is found.
Select a
station
Repeatedly press
....
~
I
.,..,.,
buttons on the panel to select a present station downward or
upward. Or press digital number (1-6) on the RC to select any present station.
Preset scan
In
tuner mode, press the ASIPS on the panel or RPTIP.SCN button on the remote to scan the
preset memorized station, each preset scan for 5 seconds. Press again to stop operation.
15

Scan
Press SCAN button
on
the front panel to search station, it will playback 10 seconds when a
station is found. Press SCAN button again to confirm the station. If you not confirm the station, it
will continue to search.
Auto
store
In
tuner mode, Press the AS/PS
on
the panel or or RPT/P.SCN button
on
the
RC
and hold for 2
seconds to store radio stations with the best reception to the preset number automatically.
Manual
store
In
tuner mode, long press the number 1-6 buttons
on
the
RC
after you find the station you
desired. The station will preset to the corresponding number.
In
tuner mode, long press the MEM button
on
the front panel after you find the station you
desired, then rotate the VOL knob to select the number 1-6
on
the radio interface, press the
VOL/OK button
on
the front panel to confirm. The station will preset to the corresponding
number.
Stereo/Mono
In
FM
band, press Stereo/Mono button
on
the
RC
to select stereo or mono sound reception.
DVD/USB/50/MMC
Operation
Load DISC
1.
Turn the power on.
2.
Press the Open button
on
the front panel to flip it down.
3.
Insert the disc with the printed side facing upward into the slot and then attach the front panel.
The DVD mode will be turned automatically.
4.
Press Open button on the panel and Eject button
in
the inner panel to eject the disc. Ifthe disc
not removed for about
10
seconds after eject, the disc will reinserted automatically. When disc
in/out, put the front at 0 degree to avoid distorting the disc.
5 You may also choose the playing mode using the Mode button.
NOTE:
The back view camera
is
available when the DVD mode
is
working.
USB Flash
Memory
To play MP3/ MP4/ WMA files from a USB flash memory, insert a USB flash memory into the
USB port
on
the right side
of
the unit. The unit will play automatically MP3/MP4/ WMAIJPEG files.
Or repeatedly press the MODE button to select USB mode.
SD/MMC Card
To play MP3/ MP4/ WMAIJPEG files
on
a SD/MMC card, insert the card into the card slot (you
should press the Open button
on
the panel to flip down front panel and insert the SD/MMC card
into card slot.) The unit will play automatically MP3/MP4/ WMAIJPEG files. Or repeatedly press
the MODE button to select
SO
mode.
Play/Pause
In
Multimedia mode, press Play/Pause button
on
the
RC
or front panel to pause playback. Press
again to resume playback.
Stop
playback
In
Mp3 mode press Stop button
on
the
RC
to stop playback. Press Play/pause button to restart
playback.
In
DVD mode press Stop button once
on
the
RC
to pause playback. Press again
to
resume playback. Press the Stop button twice
to
finally stop playback. Press the Play/Pause
button to restart playback.
Select
track
16

~~~
Press the M.SEL button on the front panel
or
RC to select the playback mode: MUSIC
MODE-.
PHOTO
MODE-.
VIDEO MODE. Then press the UP/DOWN button on the RC, also you can
rotate the VOL knob or press the
·~~
or
.......
on the front panel to select the file you desired to
playback. Press ENTER button on the front panel or RC to enter the next menu, press the MENU
button on the front panel to turn to previous menu. Press the MENU button on the RC to back to
main menu.
During playback press SEEK-
•~~
or
SEEK+
.......
on the RC
or
front panel to play the previous
or next track. You can play the tracks by pressing Play/Pause button. Press number button (0-9)
on
the RC to select the desired track and then press ENTER button on the RC to confirm
playback
. .
· :
Fast
forward/rewind
During playback press and hold repeatedly SEEK-
·~~
or
SEEK+'
.......
on the RC
or
the panel
to activate fast backward
or
forward playing. With each pressing, the playback speed will
increase. While fast playback, press Play/Pause button on the RC to resume normal speed.
When fast backward/fo-rward playback reaches the
pr~vious
or next track, the unit will resume
normal payback.
A-B
segment
repeat
During playback, press it at the starting point
of
section you want to repeat (A), press this button
again at the ending point
of
the section you want to repeat (B), section
A-8
repeating starts.
Press it again to cancel the A-B repeat function.
Random
playback
In
Media file mode, press ROM button on the RC to set shuffle playback on or off.
Introduce
playback
In
CD mode, Press INT button on the RC to activate introduction function. Several initial seconds
of
each track will be played. Press the button again to cancel intro playback.
GOTO
During playback, press and hold AU10/GOTO button on the RC to select playback track
or
chapter. Then a time search message box will display on the screen. Input the start time you
want the track
or
chapter to start. Press ENTER to confirm. The track
or
chapter will start from
the time you set.
Repeat
playback
During playback, press P.SCAN/RPT button on the RC
or
front panel repeatedly for repeat
playing in different modes: Repeat one, repeat track, and repeat all, repeat chapter, repeat title,
· repeat off.
PROG
playback
Press PROG button on the RC to enter program list.
Press
•1•/t/f
buttons and digit buttons to enter the number
of
the desired track to be on
selected position. For DVD and file disc, select title and chapter number; For VCD and CD,
select track number.
Move the cursor to select START and press ENTER button on the RC to play.
If you want to change page, move the cursor to NEXT
........
for PREV
·~~
and press ENTER
button on the RC to change next
or
previous page. ·
Ifyou want to cannel PROG playback, press again PROG button on the RC and then select Stop
option to stop PROG playback.
17

OSD function
During playback, press repeatedly to show display information. Such as: Number of title, number
of chapter, TITLE elapsed => TITLE remain => CHAPTER elapsed => CHAPTER remain
=>Display off.
Zoom in/out
Press it and hold for two seconds in Movie mode to zoom the image in or out in the sequence of
2x-> 3x-> 4x-> 1/2-> 1/3-> 1/4->normal.
PBC function
During VCD disc playback, press and hold STOP/PBC button on the RC to set PBC on or off;
When PBC is on, the screen will show PBC menu. Ifthe menu consists
of a list of titles, you can
select a desired one using number buttons on the RC.
Changing angle
Press it repeatedly to change the viewing angle (Available only with a recorded DVD file or DVD
disc that support multi-angle playback)
Select audio language
During DVD disc playback, press AU10/GOTO button on the RC repeatedly to select the audio
language to listen. (Available only with a recorded DVD file or DVD disc that support
multi-language playback).
Select subtitle language
If your DVD disc supports multi-language subtitle, press SUB-T button on the RC repeatedly to
switch among disc-supported language.
Select sound channel
During VCD disc playback press AUDIO/GOTO button on the RC to select the sound channel:
L-MONO=>R-MONO=>MIX-MONO=>Stereo.
Dual function(if you need)
DUAL KEY setting: Short press to switch DUAL function on/off. During Dual operation, long
press it switch C-DUAL and D-DUAL.
Activating Dual Zone Mode
-Access GENERAL setup
in the SETTINGS menu and find DUAL mode and select ON.
Insert a DVD or begin playing a movie from SD card or USB.
Controlling the Front Zone (C-DUAL)
Press DUAL button on the RC, C-DUAL appears on the screen.
Press the MENU button on the RC or front panel to return to the main menu. Select the
mode you wish to use
in the front zone.
-The units screen will change to the selected mode. The DVD or SO/USB movie will
continue to play only on the
AV outputs, while the selected mode audio is played through
the front and rear LINE outputs. All front panel and remote controls will affect only the
selected mode activated for the front zone.
Controlling the Rear Zone (0-DUAL)
During C-DUAL mode, press and hold the DUAL button on the RC until D-DUAL appears
on the screen.
All front panel and remote control functions for DVD, USB, or SD, including volume, will
control only the media playing for the rear zone.
18

1. Connect TV antenna, and then press MODE button to select TV mode.
2. In TV mode, press the Play/pause button once to enter TV menu setting.
3. Press thet/• buttons on the remote control or turning the knob clockwise or counterclockwise
on front panel to select one
of the setup pages: Auto program => Manual program.
4. Press VOL button on front panel or ENTER button on remote control to enter the page.
5. Press thet/• buttons to select the setting.
6. Press VOL button on front panel or ENTER button on remote control again to confirm, press
Play/pause to return to settings list.
TV MENU
Press the MEM button to enter the setup menu
of TV.
Auto program {Auto seek mode)
• System
Select the menu item is to set TV system: NTSC=>PAL=>SECAM, press ENTER button on
remote.
• Audio
Select this menu item is to set the TV sound system:
1) When system setting PAL, TV sound system can set 8/G=>I=>D/K=>/M/N, press ENTER on
remote.
2) When system setting SECAM, TV sound system can set 8/G=>I=>D/K, press ENTER on
remote.
3) When system setting NTSC, M/N sound system can be selected only.
• Search
Select this menu item is to start searching and storing stations automatically.
Manual program {manual seek mode)
Storage
Select this menu item is to set the storage number.
• System
Select this menu item is to set TV system: SECAM => NTSC =>PAL, press NTER button on the
remote control to select.
• Audio
Select this menu item is to set the TV sound system:
1) When system settings PAL, press ENTER on remote
or tap the screen button to select TV
sound system: 0/K=>M/N=> 8/G=> I.
2) When system setting SECAM, TV sound system 8/G=>I=>D/K.
3) When system setting NTSC, M/N sound system can be selected only.
Channel
Select this menu item is to set your desired searching channel, press •t• button on the RC to
select one, or press
~~~ I .... 1icon to select channel.
• Fine
Select this menu item is to fine TV tuning and sound until it achieves the best quality, press •t•
button on remote to adjust.
• Memory
Select memory on or off is to set whether memory the searched station or not, press
ENTER on remote control to select.
19

BLUETOOTH SECTION Only for VR-3458 /VR-3458Tmodel
Warning: Driving and having a Telephone conversation atthe same time is dangerous, please
park your car before having a telephone conversation. The supplier assumes any and all liability
when this warning is not followed.
To enter Bluetooth mode, you can press mode button on remote or on front panel.
BT
Main Menu
Bluetooth disconnect mode Bluetooth connect mode
A user can make own choice by press
·~~
I
.......
on the panel or
•l•ltlf
on the RC to select
the icons as below.
Select CALLING icon to use phone functions.
Select MUSIC icon to start BLUETOOTH music player.
Select DAILED icon to display the phone number dialed out.
Select RECEIVED icon to display the phone number received.
Select MISSED icon to display the phone number missed.
Tap PHONEBOOK icon to use phone book functions.
Pairing Mode
At
the 1sttime when using BLUETOOTH, you need to pair the mobile phone first.
When a phone have not been paired with the unit, the BT icon and Pairing mark will blink
continually on the panel.
When the unit have connect with phone, the BT icon will turn
on
and the Mobile phone name (if
available) will be display on the panel.
According to mobile pairing device manual, after searching new device (Sound Stream), select it,
input password "0000" and confirm ok, device paring is finished.
The text 'Enter Number' will shows on the panel afterthe pairing is completed. It means device is
connected and ready for BLUETOOTH communication.
Auto-connect- Disconnect
When power on the unit, the last paired phone will be connected to the device via Bluetooth
automatically, after searching about one minute,
if
the device cannot find the paired phone, it will
stop searching. When
in
standby mode (unconnected), long press Bluetooth button on remote
control to active auto-connect function and the device will search the last paired phone.
If
you want to disconnect the Bluetooth connection, justturn offthe Bluetooth on the phone.
1.CALLING
Rotate Volume knob
on
the front panel
or
press
•1•/t/f
on the RC to select CALLING icon and
press VOL button on panel or enter button on the RC to confirm the selection to enter call mode.
In Call mode, the unit can be used
as
your phone. Making and receiving calls are possible with
BLUETOOTH. Simply press phone number on the
RC
and press button to make a call,
and press •
.....
button to hang up. 20