Soundstream VR-930 User manual

VR-930 I VR-930T
VR-930B/ VR-930BT
Detachable 9.3" Monitor
Capacitive Touch Screen
DVD/CD/MP3/MP4
AM/FMRadio
With Bluetooth (only for VR-930BNR-930BT)
External TV box (only for VR-930TNR-930BT)
Owner's Manual
Take the time to read through this owner's manual.
Familiarity
with installation and operation procedures will help you obtain the best
Performance
from your new DVD-receiver.

To promote safety, certain functions are disabled unless the parking brake
is
on.
The Unit
is
designed to detect parked status and must
be
connected to the power supply side of the
parking brake switch. Improper connection or use
of
his connection may violate applicable law
and may result
in
serious injury or damage. To avoid the risk
of
damage and injury and the
potential violation of applicable laws, this unit
is
not for use with a video screen that
is
visible to
the driver.
• To avoid the risk of accident and the potential violation of applicable laws, the front Video
image feature should never
be
used while the vehicle is being driven. Also, other video
displays should not
be
in
a location where it is a visible distraction to the driver.
In
some
countries or states the viewing
of
images on a display inside a vehicle even
by
persons
other than the driver may
be
illegal. Where such regulations apply, they must
be
obeyed
and this unit's DVD features should not
be
used.
• Please remember to wear your seat belt at all times while operating your vehicle. If
you
are
ever
in
an
accident, your injuries can
be
considerably more severe if your seat belt
is
not
properly buckled.
• The supplier waves any and all liability when these warnings are not followed.
OPERATION PRECAUTIONS
• Only connect to a 12Vdc battery and negative grounding.
• Avoid placing the product
in
direct sunlight,
in
areas with high levels of dust, high
temperatures (over 40°C) or high humidity (over
90°/o).
In
case of high temperatures, cool
down the car interior by means
of
ventilation or air-conditioning.
• Operate
in
well ventilated areas.
•
Do
not turn
on
or off the product
in
short intervals. When turning the unit off, wait for at least
10
seconds prior to turning the unit
on
again.
Do
not operate the player with scratched,
bended or broken discs and when a disc
is
not loaded properly, do not force it into the
player.
• Do not watch video playback while driving which will cause serious danger and risks of
traffic accident. It may violate the laws and regulations.
(There may
be
exceptional case, i.e., using rear view camera and navigation system)
• Do not install the unit where the operation for safety driving
is
restrained.
• Do not disassembly the unit by yourself, if need repairing, please take the unit to the after
service center.
• Do not open and close the monitor manually, it may damage the monitor tilt system.
• Do not touch the LCD screen by hard objects, it may damage or give scratch to the LCD
screen.
• If the back
of
monitor touches dashboard or air-conditioner inlet etc after open the monitor,
then setup TILT level
in
monitor TILT menu to prevent damage from repeat touching.
• Car parking under direct sunlight may increase the temperature inside the car and the unit
may not
be
in
proper operation, please try it again after the temperature returns to normal.
• Do not replace the fuse
on
the power cable without professional guidance, using improper
fuse may cause damage to the unit or even cause burn the unit.
•
Do
not use irregular shaped Disk.
•
IR
remote control operation may
be
hindered by monitor when the monitor
is
opened, thus
please use the remote control at the similar level of remote control receiver.
• Do not install the unit where the cooling fan is blocked.
2

WARNING! .................................................................................................................1
OPERATION PRECAUTIONS....................................................................................2
ACCESSORIES..........................................................................................................4
UNIT INSTALLATION AND REMOVAL......................................................................4
WIRING CONNECTIONS ...........................................................................................7
PANEL........................................................................................................................9
REMOTE CONTROL................................................................................................ 1
0
REMOVE BATTERY................................................................................................. 13
MAIN MENU .............................................................................................................13
+ RADIO PLAYER................................................................................................... 14
+ DVD PLAYER ...................................................................................................... 15
+DISC/USB/SD/MMC INTERFACE OPERATION .................................................. 16
+AV-IN
MODE......................................................................................................... 16
+SETTING
CONTROL ............................................................................................ 17
SOUND CONTROL .................................................................................................. 17
DISPLAY CONTROL ................................................................................................ 18
GENERAL CONTROL .............................................................................................. 18
RADIO CONTROL.................................................................................................... 18
DVD SET UP MENU................................................................................................. 19
SYSTEM INFORMATION .........................................................................................20
CALIBRATION..........................................................................................................20
TV SECTION(ONLY FOR VR-930TNR-930BT)....................................................... 20
BLUETOOTH SECTION (ONLY FOR VR-930BNR-930BT) .................................... 22
SMART CONTROL(ONLY FOR VR-930NR-930T}
.................................................. 24
OTHER FUNCTIONS ...............................................................................................25
NOTES ON DISC .....................................................................................................26
TROUBLESHOOTING..............................................................................................27
TROUBLESHOOTING..............................................................................................28
TECHNICAL SPECIFICATIONS...............................................................................29
3

ac age contams t e o owtng accessones or tnsta atton an
p k h
f
II
f .
II
.
d f hoperatton o t e
umt.
(1) Mounting Strap
(2) Bolt
(3) Screw
(4) Mounting Collar
(5) Release Key
.
'·
6 8
9
0
Remote Control
Power Cable
II
II
Trim ring 1
Note:
1
~
o o
c:::::)
o o
o)
1
/)
;:<:
~y
4
~
~
~€JI'
-
~
C"''"-
P '
-
~
~~
--
_,;.,&
:-
__
~
"'""/fi
"'"'"'
I
{;::>
If;
""'
!
'J
•
,
~..,-
~~~
!7
I
~
.
2
~
it·
.::!•
·
~
~
(0
f
I)
"
'.
p
tona
....
.,
;J!L..,<:r
"'"
p
-'
\
1-
•
~
'
2
~
Warranty card
User
Manual
Warranty card User Manual
Smart control cable (only for
W/0
Bluetooth model)
Trim ring 2 (optional)
~
r
AV
in
cable
RCA Cable
TV box (only for TV
model
Product image may vary from the actual delivery.
4

Installation:
1) Install the mounting sleeve into the
dashboard.
~
-
f
'
3) Slide the unit into the mounting sleeve.
5) Install the panel to the unit.
7) Press the panel, make sure the gear
locked to the mounting hole.
·
;:.
--
5
2) Bend the tabs into place to secure the
sleeve.
4) Install the trim bezel onto the unit.
6) Make sure all faceplate tabs meet properly
wit~
the mounting plate.

Removal:
1) Press the button.
3)_Take faceplate
off
of
the mounting plate.
5) Detach the trim bezel.
7) Pull the unit out
of
the mounting sleeve.
Note:
2) Safely detach the faceplate.
4)
Take the panel out.
6) Insert the keys into the opening between
the unit and the mounting sleeve to unlock.
8) Illustration
of
removal.
Before starting installation
of
the unit, make sure the wiring is connected properly.
Use only the parts provided with the unit to ensure proper installation.
The use
of
unauthorized parts
may
cause malfunction.
Install the unit where it does not get in the driver's way and will not injure the passenger in case
there is a sudden stop, like an emergency stop.
The control panel can easily be damaged by shocks. After removing it, place it in a protective
case and be careful not to drop it
or
subject it to strong shocks.
The rear connector that connects the main unit and the control panel is an extremely important
part. Be careful not
to
damage it by pressing on it with fingernails, pens, screwdrivers, etc.
6

-L.I
liiiJ
RADIO
ANT
[l]lllllll
0
•
• •
• • •
• •
, 3
s
7 '
t
1
lJ
15
• • • • • •
• •
2 ' ' I 10 12
14
16
.
USE
10
AMP
AGC
REPLACEMENT
FUSE
ONLY
POWER
CONNECTOR
1 .
RL
(GREEN)
2 :
RL
-(GREEN/BLACK)
5 :
Fl
(WHITE BLACK) 6 FL
·.
(WHtTE)
9 .
REVERSE
LAMP
..
(ORANGE
BLACK)
11
.
REMOTE
TURN-ON•(BLUE/WHITE)
13.
PARKING
BRAKE..(PtNK)
15
.
BATIERY
12V•(YEUOWJ
3
RSh(PURPlE)
1
FR
(GREY BLACK)
10
ILL (ORANGE)
12
POWER ANT+(BLUEJ
14
GNO
(BLACK}
16
IGNITKlN
12V•(REO)
()
4
RR..(PURPlE/BLACKl
8
FR
·
(GREVJ
NOTE: Never connect cable to the system while it is connected to the battery power. Whenever
the unit is disconnected from the battery, the preset memory will be erased and the unit will go
back to its factory defaults.
When the brown cable for steering wheel control connected to the steering wheel, we can use
the steering wheel to control some unit
Note:
To watch video the parking wire should be connected to break signal. 2 cables is
connected to a Hands-Free device (not included).
Parking wire
Note:
The parking wire is connected with brake signal; for safety, the programs can be seen on
the monitor after braking the car.
Parking
Brake
switch
(Activated
by
parking
brake
)
Parking
Brake
wire
from
car
OVO
player
(Pink/Black)
~================~l
To
metal
body
part
or
chassis
ground
of
your
car
Connecting the reversing line
to
taillight
on
the
car
To
reversing
line
'I
1
~~
To
taillig
hI
====::tTI~;:'
=/=/
======~
'
(
To
Car
Battery
7

~
After connecting, when you start up the reverse gear, the unit will receive the picture from car
rear view camera.
Note:
Only use groundless loudspeakers.
Use only loudspeakers of minimal 40Watt, using fewer watts may result
in
damaging
your loudspeakers at higher volumes.
Use
4-8
n (Ohm impedance) loudspeakers only; using higher or lesser impedance may
damage the unit.
Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car
body (GND). The unit
is
using a BTL circuit and each loudspeaker must
be
connected
with insulated cables according the diagram.
Loudspeaker cables and/or optional external power amplifiers must always
be
about
30cm away from the antenna and/or antenna extension parts.
Connect the speakers according the following diagram, incorrect connections will damage the
unit or your loudspeakers
Correct connection
Left
front-
Right front
1
Left
rear-
Right rear
*
z1
xy;>
~
aa
't:
it
M#tJv\+1
'
01
Incorrect connections
8

1 2 3 4 5 6 7
arlttit
,
•cj;
,
1€
I
"----./
10
v
11
12
13
[ J
I
I I I
r-r·-·t
RESET
[
lfl
n J
1. MIC
2. POWER/ MUTE button
Press it to turn on the unit. When the unit is on, short press it mute the volume output, long
press it to turn the unit off.
3. MENU button
Press it to turn to the main menu quickly.
4. SETUP/EQ button
Press it to turn to setting menu quickly. Long press the button to enter into EQ setting.
5. EJECT button
Press to eject a disc. If the disc is not removed for about 10 seconds after eject, the disc is
reinserted automatically.
Press and hold for 2 second to adjust the Monitor tilt angle: TILT ANGLE 1 => TILT ANGLE 2
=> TILT ANGLE 3 => TILT ANGLE 4.
9

6. Release button
Press to detach and release the front panel. When the unit was released, it will switch off
automatically after a few second. Detach/Attach
the Panel: Press REL button and pull out the
panel towards yourself to release the panel. To attach it, press the control panel into the main
unit until the "click" sound is heard.
7. SD/MMC CARD slot
SD/MMC card slot, for Multimedia playback files only. Insert a SD/MMC CARD into this slot and
the unit will automatically start reading and playback the card. * Supported Music File Format:
MP3, WMA Files.
8. AV-in Jack
Putthe AV plug into the AV-IN jack which was marked on front panel.
9. USB slot
10. TFT display
11. RESET button
Press it with a thin, sharp object. The device will then be reset to factory default settings.
12. Anti-Theft LED flash
13. DISC slot
REMOTE CONTROL
f\ I
~l
- ---+-
l ;-
14
. .,
... _ 1: MODE
( ~ \
·• r '· <.!> ' MODE'
....
~r
\ 1$l
2: POWER
/ I (
Hi • 3: BAND/RANDOM/CLEAR
(•)
::-
~b- 0 +-
3j
--~
MENU
( 11
4: ENTER
' ROM
5: UP/DOWN/LEFT/RIGHT
4
_.,
I
~
;. ; 6: EJECT
' j;
I/ .. )
EN T ER
'S e tup
18 '
7: STEREO/MONO/*
I \.: _
r_ -·
..r 1g 8: P.SCN/RPT/#
I " \ -r
-.., \ 9: BACKWARD/SEEK-
'6;
·• • JEJECI)
~ng1e
IN! / I <
20 1 FAST BACKWARD
.7
! 21 ; 10: LOUD
(8 >-
VOl+
.l!JL
-~ ~t
11 : 0SD
'~/
9! • 1 2l
12:PBC/STOP
3~
LOUD
S[(K
SEL
SEEK•
- 24
13:DIGIT NUMBERS
... ........-
t 11 '>
l
r-----
- 25
14:PLAY/PAUSE
1_, ~
• f
050)
I
Au[),O\
' 26:
15: MUTE/BLUETOOTH
..
J PBC
I VOL-1
\GrTO/
16:MENU
17:SUBTITLE
' 18:SETUP
1 2 3 4 19:ANGLE/ACCEPT (optional)
..... 5 6 7 8 20: INT/REJECT (optional)
21: VOLUME PLUS
22: A-B/ZOOM
9 0
OP ['l
1· 23: SEL
HI
/ 24: FORWARD/SEEK+
I FAST FORWARD
I
L ______
25: VOLUME MINUS
---
26: AUDIO/GOTO
27: OPEN(option withoutfunction)ITILT
10

1. MODE button
Press it to select the mode: Radio, DISC (if there is a disc
in
unit), USB (if there is a USB
device
in
the unit), CARD (if there is a SD/MMC card
in
the unit), Bluetooth (only for VR-
930BNR-930BT}
and AV IN.
2.
POWER
button
Power on or off
3. BAND/ ROM/CLEAR button
In
Radio mode, press it to change radio band
in
sequence
of
FM1
~
FM2
~
FM3
~
AM1
~
AM2.
In
DVD mode, press to play randomly .In Bluetooth mode, press briefly it to clear single
wrong number. Long press it to clear all the wrong number.
4.
ENTER button
Press it to confirm selection
or
setting.
5.
Cursor
•1•1
•I•
buttons
Use the
t/•/
•I•buttons to select the menu item: the title, track or to show next frame.
6.
EJECT button
Press it to eject the disc.
7. STEREO/MONO/* button
Press STEREO button to select STEREO or MONO.
In
BLUETOOTH mode, press it to make a
*
symbol.
8.
P
.SCN/ RPT
/#
button
In
SO
CARD/ USB mode, press to repeat REP 1 => REP DIR => REP ALL
In
DVD mode, press to start repeat REP OFF=>REP Chapter=>REP Title=>REP Off.
In
Radio mode: PS (Preset Scan): Press to scan all preset stations
in
the memory
of
the current
band and stay on each memory stations for about 5 seconds.
AS (Auto Save): Long press to save the stations with good reception automatically.
In
BLUETOOTH mode, press it to make a # symbol.
9.
1-t-4/
SEEK- button
In
DVD mode, Press
l-4-4
button to skip to the previous track. Press and hold
1-4-4
button for two
seconds to activate fast reverse (REW) search
in
a track.
In
RADIO mode, press
l-4-4
button to start searching automatic, press and hold for two seconds to
start manual searching
1-4-4
button Frequency down.
10. LOUD button
Press to set LOUD on or OFF.
11. OSD button
In
DVD mode press it to enter the OSD menu, press and hold for 2 seconds to set video setup.
(HUE I SATURATION I COLOR RESET I BRIGHT I CONTRAST I SHARP I BACK)
12.
STOP/PBC button
Press it to Stop playback from the current position, press it again to final stop to the very
beginning. Press PLAY/PAUSE button to play.
Press and hold for two seconds to set PBC on/ off
in
VCD mode.
13. Digit 0-9 buttons
In
radio mode, select 1-6 the desired band;
In
DVD mode, select track.
In
BLUETOOTH mode, press it to input phone number, long press
0
number to make a
+
symbol
14. PLAY/PAUSE button
In
DVD mode, press it to pause playback, press again to resume.
15. MUTE/BLUETOOTH button
X :Short press this button to mute the volume output, press it again to resume volume.
Long press this button to enter into Bluetooth mode.
16. MENU button
11

~
'
Press it to show main menu,
in
DVD mode, long press it to enter TITLE MENU (Enable only if
the DVD disc with title menu).
17. SUBTITLE
button
Press it to select the subtitle language (Available only if the disc with subtitle function).
18. SETUP
button
In
DVD mode press it to enter the setup menu.
19. ANGLE /ACCEPT
button
In
DVD mode, press it repeatedly to change the viewing angle (Available only with a recorded
DVD file or DVD disc that has this function).
In
BLUETOOTH mode, press to make a call after inputted a phone number or accept an
incoming call.
20. INT /REJECT
button
Press it to activate the intra function. You can play the beginning of every track for 10 seconds
in
sequence.
In
BLUETOOTH mode, press to reject a coming call or hang up while calling
21. VOL+
button
Press to increase volume level.
22. A-8/ZOOM
button
During playback, press it at the starting point of section you want to repeat (A), press this
button again at the ending point of the section you want to repeat (B), section A-8 repeating
starts. Press it again to cancel the
A-8
repeat function.
Press it and hold for two seconds
in
DVD mode to zoom the image
in
or out
in
the sequence of
ZOOM 2-> ZOOM 3-> ZOOM 4-> ZOOM 1/2-> ZOOM 1/3-> ZOOM 1/4.
23. SEL
button
Press it to enter the SOUND SETTING menu, and press Cursor UP/ON buttons to choose an
item and press cursor left/right buttons to set the item. Press SEL button again to exit the menu.
24.
.-.-1/
SEEK+
button
In
DVD mode, Press
.,..
,button to skip to the next track. Press it and hold
....
,button for two
seconds to activate fast forward (FF) search
in
a track.
In
RADIO mode, press
.,..
,button to start searching automatic, press and hold for two seconds to
start manual searching
....
,button Frequency
up.
25. VOL-
button
Press to decrease volume level.
26. AUDIO/GOTO
button
In
DVD mode press it to select the audio language.
In
VCD mode, press it to select the sound track
in
the sequence of MONO L =>MONO R
=>STEREO.
Go to:
in
DVD mode, press and hold for 2 seconds to show TIME SEARCH menu, select
number and confirm to go to certain position directly. When
press•
button to enter
TITLE/CHAPTER selection mode, select number and confirm to go to certain TITLE or
CHAPTER position directly.
27. OPEN/TILT
button:
Press it to adjust the tilt angle of monitor.(The open button is an option without function)
12

Note:
• The distance may vary according to the brightness
of ambient light.
•
If the remote is not used for an extended period of time, remove the battery to prevent
possible damage from battery leakage and corrosion.
• Do not place any objects between the remote control unit and the sensor on the unit.
• Do not drop the remote control onto the floor; it will damage it beyond repair.
• Do not use the remote control unit, while simultaneously operating the remote control unit
of any other equipment; they may interfere resulting in improper operation.
• The battery normally last for about one year although depending how often the remote
control is used.
If the remote control unit isn't working even when it is operated nearthe unit,
replace the battery with a new battery
of the same make and use only a lithium cell battery
type: CR2025 (3V).
• Dispose empty batteries
in accordance with your local governmental regulations.
• Do not short-circuit, disassemble, heat or dispose
of fire or flames the battery.
• Keep the battery out
of reach of children, should the battery be swallowed, immediately
consult a doctor.
MAIN MENU
The best way to discover the program is to explore each screen in detail, and to find out how to
move from one to another. Read this chapter for a guided tour.
Unit starts by displaying the Main menu.
This is the root
of the screen hierarchy, and you can simply access all features by tapping on
the touch screen buttons.
Tap the icons to enter a desired mode. '
13

+RADIO PLAYER
To start Radio, tap RADIO button on main menu screen.
a Mute the sound ..
• Increase the volume.
• Decrease the volume.
~~Touch this button can choose FM1, FM2, FM3, AM1, AM2.
=:1 Touch this button can scan the stations from 1-6, long touch it to save the stations with
~~~~~reception automatically and scan each station for about 5 seconds.
IW Touch this button to search stations backward automatically.
mJ Touch this button to search stations forward automatically.
mTouch this button to open manual select station backward.
mTouch this button to open manual select station forward.
14

+DVD PLAYER
To start DVD Player, tap on DVD button from main menu screen.
TOUCH SCREEN MENU
You will not see any buttons while DVD is played. Buttons will appear when you tap on TFT
screen. T the screen n to hide the buttons.
Insert DVD disc Insert VCD disc
NOTE
1. DVD Player will automatically start playing when you insert any DVD disc, MEMORY
card or USB device.
2. Warning displays ifthe vehicle is moving for driver's safety.
3. DVD Player will not only play video, but also picture and music files as well.
File Management
DVD mode files in a) Disc b) USB c) MEMORY card (MEMORY card slot in inner panel).
VOL- 20 VOL+ VOL increase or decrease by touch the button accordingly.
......
Pause playback. Press it again to continue playback.
• Press it to Stop playback from the current position, press it again to final stop to the very
=~
iiiil;lii Start fast rewind or fast forward. Press one of the keys again to change the spooling
i.ii · Press the Play key to regain normal playback.
In DVD mode, touch it can choose Repeat chapter =>repeat title =>repeat off.
In VCD mode, touch it can choose Repeat REP 1 =>REP ALL=> REP ALL.
~~Touch it to select the subtitle language (Available only if the disc with subtitle function).
~~~in DVD mode touch it to select the audio language (Available only if the disc with subtitle
function);
In VCD mode touch it can choose MONO L---MONO R---STEREO.
•
In VCD mode touch it can choose PBC ON or OFF
•
In DVD mode touch it to enter TITLE MENU (Enable only ifthe DVD disc with title menu).
-~~ Touch it to select previous or next track.
s::::::::::ID Select the viewing angle. of the touch-screen.
15

+DISC/USB/SD/MMC INTERFACE OPERATION
When a file disc, USB or a memory card is played, the screen will show following interface:
When press the stop button
Mute the sound.
Stop button. Press it to stop playback from the
current track, press it again
to final stop to the very
be
Play/pause button. Press it to pause the track,
ress again to resume.
Press it button to restart a track,
FRx2x4x8x20-play will be display.
Press it button to skip to the next track.
FFx2x4x8x20-play will be display.
Press it
to skip to the previous track.
Press it to skip to the next track.
~~~Press it to activate the intro function. You can
play the beginning
of every track for 10 seconds in
~ence.
lilill Press it to repeat REP 1 => REP DIR => REP
ALL
1!1!11
~ Press itto play track randomly.
__ Press it to enter previous page.
L Press it to enter next page.
• Press it to
go to folder selection.
, following interface will be display.
Press it to retune to the file menu.
@J Press it to select the file forward.
Press it
to select the file backward.
16

+AV-IN
MODE
To start AV-IN Mode, tap on AV-IN button from main menu screen.
Connect the external audio/video signal source to this unit. Select AV-IN mode in the main
menu or by pressing repeat Mode button on the front panel.
Note: Ifthere is no external video input, the TFT displays "NO SIGNAL".
Press the
¢1
icon to be back to main menu.
+SETTING
CONTROL
Your device has default system settings. You can customize the settings to suit your personal
needs. Once you change settings, your new settings will remain until you change it again.
To start SETTING, tap it on main menu screen.
SOUND CONTROL
Tap SOUND button to show SOUND 1 menu.
Tap m
button to show SOUND 2 menu.
Tap m
button to show SOUND 3 menu.
17
EQ Select EQ mode
BAS LEVEL Bass up/down
TRE LEVEL Treble up/down
BALANCE Left/Right Balance Control
FADER Front/Back Fader Control
BEEP Set keypad sound on /off
LOUDNESS Set loud on /off
LOUD LEVEL Adjust loud level
SUBWOOFER Setsubwoofer on /off
SUBW LEVEL Adjust subwoofer level
SUBW LPF Select a subwoofer crossover
o tion: 80HZ,120HZ,160HZ

DISPLAYCONTROL
GENERAL CONTROL
BACKLIGHT Backlight setting LOW, MID,
HIGH
Tap GENERAL button to show GENERAL menu.
TILT Adjust monitor tilt angle
ANGLE
CLOCK Set clock display time on
or off.
DISPLAY
CLOCK Set 24hour format or 12hour
HOUR format
CLOCK display time
SETTING Automatic Bluetooth connection
AUTO to a previously connected
CONNECT mobile telephone.
(only for VR-930BNR-930BT)
ISET TIME IAdjust clock display time
RADIO CONTROL
Tap RADIO button to show RADIO menu.
AREA Set AREA: EUROPE, U.S.A,
SOUTH AMERICA,RUSSIA
STEREO Set STEREO ON or OFF
18

DVD SET UP MENU
Tap the DVD button in main menu to enter the DVD player. Press the SETUP button to enter
into the system settings main menu; press the up
or down arrow buttons to move to the
highlighted menu item and select one
of the Setup Pages:
[1]. Subtitle Lang setting:
With this option you can select the preferred language for the subtitles. When the selected
language is recorded on the disc then this language will automatically be shown. If not, the first
language recorded on the disc is displayed.
[2].Audio Lang setting:
With this option you can select the preferred language for the audio output. When the selected
language is recorded on the disc (not all discs have multiple languages recorded) then this
language will automatically be played. If not, the first language recorded on the disc is played.
[3]. DVD Menu Lang setting:
With this option you can select the preferred language for the disc menu. When the selected
language is recorded on the disc then this language will automatically be selected.
If not, the
first language recorded on the disc is displayed.
[4]. MP4 Language
With this option you can select the preferred language for the MP4 menu.
[5] Password:
The password for this unit is initially set to factory default 0000. If you want to change your
password, you need to enter the old password first and confirm it, and enter a new password
and confirm. WARNING:
if you forget your password, there is no possibility to reset the
password again. Do not forget your password and write it down
or store the password in a safe
place.
[6] Rating I PARENTAL SETUP.
For DVD discs which support the USA rating system, setting up rating cont(ol can prevent
children from watching content that might not be suitable for their age. You are asked to enter
the password when you change the rating setting. The default password is 0000.
Code Description
1.NONE Kid safe
2.G General Audiences -ALL ages admitted
3.PG PARENTAL GUIDANCE SUGGESTED-Some material may not be suitable fo
r children
4.PG-13 PARENTS STRONGLY CAUTIONED-Some material may be inappropriate fo
r children under 13
5.PG-R Restricted, under 17 requires accompanying
~a rent or adult guardian.
6.R RESTRICTED-Under 17 requires accompanying parent
or adult guardian
7.NC-17 NO ONE 17 AND UNDER ADMITTED
8. Adult Above 17 Admitted
[7]
TV SHAPE:
Set TFT screen mode to the correct ratio:
19

Three screen ratio modes are available, Normai/PS (4:3 Pan Scan), Normai/LB (4:3 Letter Box)
and Wide (16:9). Different disc formats will display different images depending this setting and
the screen size used.
[8] NTSC/ PAL:
Select this menu item to set up your preferred video output format. PAL is commonly used
in
Europe. NTSC is commonly used
in
the USA and Japan. Auto is commonly used.
[9] DEFAULT:
Factory reset. Set all values to Factory default values
including memory and preset stations.
SYSTEM
IN
FORMAT/ON
Press SYSTEM button to show the information
of
the
system. You can view detail system information
including serial number
of
the software.
CAL/
BRAT/ON
The calibration
of
the screen is useful when some
malfunction occur with the touch screen and it needs
adjustment.
CALIBRATION procedure
of
the touch screen is
described as below: When the target moves to
another position, tap and hold at the center
of
the new
target. Repeat each time
to
complete the calibration
process. When the calibration has been completed,
the device switches back to the previous operating
mode and retain the previous setting.
If
you press
Reset button, the setting will return to factory setting.
TV SECTION ONLY FOR VR-930TNR-930BT
CAUBRATION
Carefully press
and
briefly
hold
stylus
on the center
of
the target longer than 1 second.
Connect a TV BOX to the TV antenna jack
of
the unit. you can tap
TV
icon on main menu
screen or press mode on front panel
or
remote.
1.
Connect
TV
antenna to the
TV
ANT wire
in
rear unit, and then press MODE button on front
panel
or
remote to select TV mode or Tap
TV
icon on main menu screen to enter TV mode.
2.
In
TV mode, press the Play/Pause buttons on front panel
or
remote once to enter
TV
menu
setting,
or
press touch screen to choose
TV
MENU icon
to
enter TV MENU.
3.
Press the
t/t
on remote
or
tap the screen to select one
of
the setup pages: Auto program
=> Manual program.
20