SOYO SY-K7VTA PRO User manual

SY-K7VTA PRO
Motherboard
Quick Start Guide
Hardware
Installation
Quick BIOS
Setup
Introduction
The SOYO CD

SOYO™
2
SY-K7VTA PRO Motherboard
Socket 462 for AMD
®
Athlon/Duron
TM
processors
VIA KT133A AGP/PCI Motherboard
266 MHz Front Side Bus supported
ATX Form Factor
Copyright © 2001 bySoyo Computer Inc.
Trademarks:
Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of
their owners.
Product Rights:
All names of the product and corporate mentioned in this publication are used for identification
purposes only. The registered trademarks and copyrights belong to their respective companies.
Copyright Notice:
All rights reserved. This manual has been copyrighted by Soyo Computer Inc. No part of this
manual may be reproduced, transmitted, transcribed, translated into any other language, or
stored in a retrieval system, in any form or by any means, such as by electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without permission in writing from Soyo
Computer Inc.
Disclaimer:
Soyo Computer Inc. makes no representations or warranties regarding the contents of this
manual. We reserve the right to amend the manual or revise the specifications of the product
described in it from time to time without obligation to notify any person of such revision or
amend. The information contained in this manual is provided to our customers for general use.
Customers should be aware that the personal computer field is subject to many patents. All of
our customers should ensure that their use of our products does not infringe upon any patents. It
is the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and not to
infringe upon or to cause others to infringe upon such rights.
Restricted Rights Legend:
Use, duplication, or disclosure by the Government is subject to restrictions set forth in
subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
252.277-7013.
About This Guide:
This Quick Start Guide can help system manufacturers and end users in setting up and installing
the Motherboard. Information in this guide has been carefully checked for reliability; however,
to the correctness of the contents there is no guarantee given. The information in this document
is subject to amend without notice.
For further information, please visit our Web Site on the Internet. The address is
"http://www.soyo.com.tw".
K7VTA PRO Serial - Version 1.1 - Edition: May 2001
* These specifications are subject to amend without notice

SY-K7VTA PRO Quick Start Guide
3
Introduction
1 1 Introduction
Congratulations on your purchase of the SY-K7VTA PRO Motherboard. This QuickStart
Guide illustrates the steps for installing and setting up your new Motherboard.
This guide provide users with the basic steps of Motherboard setting and operation. For
further information, please refer to the SY-K7VTAPROUser’sGuide that came with your
Motherboard.
Unpacking
When unpacking the Motherboard, check for the following items:
u The SY-K7VTA PRO KT133A AGP/PCI/ISA Motherboard
u The Quick Start Guide
u The Installation CD-ROM
u SOYO Bonus Pack CD-ROM
u One IDE Device ATA 66 Flat Cable
u One Floppy Disk Drive Flat Cable
u One Heat Sink Compound

SY-K7VTA PRO Quick Start Guide
4
Introduction
SY-K7VTA PRO Motherboard Layout
PRT
PS/2 KB
Connector
PS/2 Mouse
Connector
ATX Power
LINE-OUT
LINE-IN
MIC-IN
GAME
COM1
COM2
USB 1_2
SDRAM
SDRAM
®
VT8363A
AGP Slot
3V
Lithium
Battery
JP5
1
3
FJ1
FJ2
1
1
3
3
J3
1 3
J2
1
3
JP7
1
3
CDIN1
1
4
ISA Slot
PCI Slot #5
Flash BIOS
PCI Slot #1
PCI Slot #4
PCI Slot #3
PCI Slot #2
IDE 1
IDE 2
FLP
Sigmatel
STAC9700
®
VT82C686B
RJ1

SY-K7VTA PRO Quick Start Guide
5
Introduction
Key Features
Ø Supports Socket A (Socket 462)
AMD® processors
¡X Supports 200MHz Front Side Bus
DDR(Double Data Rate) transfer
on
Athlon(750MHz~1.2GHz)
Duron  (600MHz~800MHz)
¡X Supports 266MHz Front Side Bus
DDR (Double Data Rate) transfer
on Athlon(1GHz~1.2GHz)
Ø PC99, ACPI
Ø Ultra DMA33/66/100 (ATA 33/66/100)
EIDE
Ø Supports Wake-On-LAN (WOL)
Ø Power-on by RTC alarm
Ø Supports onboard hardware
monitoring and includes Hardware
Doctor
TM
utility
Ø Supports PC133/ PC100 SDRAM
and Virtual Channel Memory (VCM)
SDRAM up to 1.5GB memory space
Ø Supports multiple-boot function
Ø 5 x 32-bit bus mastering PCI slots
Ø 1 x 32-bit AGP 1X/2X/4X slot
Ø 4 x USB ports onboard
Ø 1 x IrDA port
Ø ATX power connector
Ø 1 x 16-bit ISA slot
Ø 3 x 64-bit DIMM slots
Ø Supports Power Failure Resume
Ø Easy CPU settings in BIOS with the
“SOYO COMBO setup”
Ø Supports Suspend to RAM
Ø Supports on-board AC97 Audio
Ø Supports CPU voltage adjustment
Ø Support “SOYO Voice Doctor”
function
Ø Supports “SOYO F.O.C.”(Fan Of
Control) function

SY-K7VTA PRO Quick Start Guide
6
Hardware
Installation
2 2 Installation
To avoid damage to your Motherboard, please follow these simple rules while
handling this equipment:
l Before handling the Motherboard, ground yourself by touching an unpainted portion of
the system's metal chassis.
l Remove the Motherboard from its anti-static packaging. Hold the motherboard by the
edges and avoid touching its components.
l Check the Motherboard for damage. If any chip appears to be loose, press carefully
to seat it firmly in its socket.
Follow the directions in this section which is designed to guide you through a quick and
correct method to install your new SY-K7VTAPRO Motherboard. For detailed information,
please refer to the SY-K7VTAPROMotherboardUser'sguideandTechnicalReference
online manual in the CD-ROM package that came with your Motherboard.
Gather and prepare all necessary components to complete the installation successfully:
u AMD® Socket462 processor with built-in CPU cooling fan (boxed type)
u SDRAM module(s)
u Computer case with adequate power supply unit
u Monitor
u PS/2 Keyboard
u Pointing Device (PS/2 Mouse)
u Speaker(s) (optional)
u Disk Drives: HDD, CD-ROM, Floppy drive…
u External Peripherals: Printer, Plotter, and Modem (optional)
u Internal Peripherals: Modem and LAN cards (optional)
Note: 1. If you want to use an external speaker connected to "Line-out" port, please make
sure to use an "amplified speaker" that can generate proper output sound volume.

SY-K7VTA PRO Quick Start Guide
7
Hardware
Installation
Install the Motherboard
To perform the installation of your new SY-K7VTAPRO Motherboard, follow the steps
below:
FOC ( Fan-Off Control )
Thenewly designedSOYO“FOC”isbasedontheconceptoftotalprotectionforCPU,whichisvery
differentfromcurrentlyseenonthemarket.TheH/Wcontrolfunctionisusedtoseeapassivesecurity
systemofmonitoringandwarning.“FOC”,designedbySOYO,givesemphasis ontheconceptoftotal
protection.S/WSimultaneousSignalFollow-upstechniquesandAutoPowerOffSystemareincludedto
preventallpossibledamagecausedbytheMAL-functioningoftheCPUfan.Withthehelpof“O/SOnTime
MonitoringAndWarning”function,providedbytheH/Wmonitoringsystem,thedouble-protectionpurposeis
achieved.
“FOC”includesthefollowingfunctions:
(1)SimultaneousSignalFollow Ups:BeforethesystementerstheO/S,H/Wwilldetectthesignalsof
theCPUfanpins, gettheirrevolutioninformationandsendittotheBIOS.
(2)AutoPowerOffSystem: IftheBIOSgetstheinformationofCPUfanrevolution,itgoeson working
normally.Ifnot,itwillinformthesystemandhavethepowersupplydisconnected
immediately.Thus,theCPUisprotectedfromoverheating.
Note:Thefollowingmustbeobservedtosecurethenormalfunctioningof“Fan-OffControl”:
1.CPUfanwithsensorpinsmust beused.
2.CPUfansapprovedbyAMDarestronglyrecommended.
3.The “HOTKEY”functionisprovidedfortheCPUfanswithoutsensorpins,toavoidthepoweroff.
Usersmaypressthe“Insert”keytojumpoverthe“Power Off”mode;gototheBIOSanddisable
“FOC”.Nowsystemcan bebooted normally.
4.Thepowerconnectorof theCPUfanmustbeconnectedtothespecified“CPUFanConnector”on
themotherboardtosecurethenormalfunctioningofthesystem.
WeprovidethefollowingUser-Friendlyprotectionfeatures:
1.Fan-OffControl:ThemotherboarddetectsthestatusoftheCPUfanandprotectstheCPUby
automaticallydisconnectingthepowersupply.ThedefaultvalueofthisfunctionisEnable.After
bootingup,theusermaydisableit.
2.CPUSocketSticker: UserswillfindastickerontheCPUsocket,whichremindsthemofthe
correctusageoftheK7CPU.
3.HeatDissipationPaste:HeatDissipationPasteisincludedforallSocket-Amotherboards,to
enhancetheheatdissipationcapability.

SY-K7VTA PRO Quick Start Guide
8
Hardware
Installation
Furthermore,westronglyrecommendouruserstoenablethefunctionofH/WmonitoringintheBIOS.This
function,togetherwiththeFOC,providethetotalprotectiontotheCPUandallowittomaximizeits
performance.
Step 1. CPU Installation
Mark your CPU Frequency: Recordtheworking frequencyof yourCPU that
shouldbeclearly markedon theCPU cover.
200MHzFSB DDRtransfer on Athlon
750MHz(100x 7.5) 800MHz(100x8.0) 850MHz(100x8.5) 900MHz(100x9.0)
950MHz(100x 9.5) 1000MHz(100x 10.0) 1.1GHz (100x11.0) 1.2GHz(100x 12.0)
200MHzFSB DDRtransfer on Duron
600MHz(100x6.0) 650MHz(100x6.5) 700MHz(100x7.0) 750MHz(100x7.5) 800MHz(100x8.0)
266MHzFront SideBus DDRtransfer on Athlon
1GHz(133x 7.5) 1.13GHz(133x 8.5) 1.2GHz(133x9.0)
CPU Mount Procedure: To mount the AMD
®
& Athlon/Duron
TM
processor that you
have purchased separately, follow these instructions.
1. Lift the socket handle up to a vertical position.
2. Align the blunt edge of the CPU with the matching pinhole edge on the socket.
3. Seat the processor in the socket completely and without forcing.
4. Then close the socket handle to secure the CPU in place.
Remember to connect the CPU Cooling Fan to the appropriate power
connector on the Motherboard. Thefanis akeycomponentthatstabilizesthe
system.Itpreventstheequipmentfromoverheatingandprolongsthelifeof
yourCPU.
1
1
3
4
2

SY-K7VTA PRO Quick Start Guide
9
Hardware
Installation
Step 2. Connections to the Motherboard
This section tells how to connect internal peripherals and the power supply to the Motherboard.
The internal peripherals consist of IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis
Fan, Front Panel Devices (STR LED Internal Speaker, Reset Button and IDE LED Switch.),
Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on connecting internal and external peripherals to your new SY-K7VTA
PRO Motherboard, please refer to SY-K7VTAPROMotherboardUser'sGuideand
TechnicalReference online manual on the CD-ROM.
Connectors and Plug-ins
Standard IrDA (Infrared Device Header): SIRCON Wake-On-LAN Header: J10
Pin1 Pin2 Pin3 Pin4 Pin5 Pin1 Pin2 Pin3
+5V NC IRRX GND IRTX 5VSB GND RING
USB3_4: USB3 USB3_4: USB4
Pin1 Pin3 Pin5 Pin7 Pin2 Pin4 Pin6 Pin8 Pin10
+5V Data(-) Data(+) GND +5V Data(-) Data(+) GND GND
CPU Cooling Fan: CPUFAN1 CPU Cooling Fan: CPUFAN2
Pin1 Pin2 Pin3 Pin1 Pin2 Pin3
GND +12V SENSOR GND +12V NC
Chassis Fan: CHAFAN Chip Cooling Fan: ChipFAN
Pin1 Pin2 Pin3 Pin1 Pin2 Pin3
GND +12V SENSOR GND +12V NC
CDLine-in:CDIN1Pin1 Pin2 Pin3 Pin4
ConnecttheCDLine-incordfromtheCD-ROMdeviceto
thematchingheaderCDIN1 LG G R
Power LED
Pin1 Pin2 Pin3
LEDNCGND
Speaker
Pin1 Pin2 Pin3 Pin4
VCC NC NC Speakerout
HDD LED PWRBT RESET STR LED
¡°
Pin1 Pin2 Pin1 Pin2 Pin1 Pin2 Pin1 Pin2
LED GND PW-BT GND PowerRST GND LEDAnode GND
ATXPOWER On/Off: PWRBT
Connect your power switch to this header (momentary switch type).
To turn off the system, please press this switch and hold down for longer than 4
seconds.
Power LED
Speaker
Reset
PWRBT
STR LED
HDD LED
++
+
+
_
_
_
_ 1 1

SY-K7VTA PRO Quick Start Guide
10
Hardware
Installation
ATXPower Supply:ATX PW
AttachtheATXPowercabletothisconnector.(ThismotherboardrequiresanATXpowersupply,anAT
powersupply canNOTbeused.)
WhenusingthePower-OnbyPS/2Keyboardfunction,pleasemakesuretheATXpowersupplyisableto
provideatleast720mAonthe5VStandbylead(5VSB)inordertomeetthestandardATXspecifications.
¡° Note: The STR LED is connected to the Voltage that feeds the DIMM sockets. Therefore
the following table applies:
Suspend to RAM Normal Operation Power Off
STR LED Blinking ONOFF
Step 3. Configure Memory
Supports PC133/ PC100 SDRAM and Virtual Channel Memory (VCM) SDRAM up to 3
DIMMs and using system memory up to 1.5GB.
Memory Configuration Table
Number of Memory Modules DIMM 1 DIMM 2 DIMM3
RAM Type SDRAM/ VCM SDRAM
Memory Module Size (MB) 32/64/128/256/512 MB
Step 4. Ratio Adjustment Setting (RJ1)
RefertothefollowingtabletosettheFrequencyMultiplierofyourCPU.
Frequency Multiplier
Setting J2 J3
Auto Short Pin1-2 Short Pin1-2
Manual Short Pin2-3 Short Pin2-3
123
123
123
123

SY-K7VTA PRO Quick Start Guide
11
Hardware
Installation
IfyousetratiotomanualandconfiguretheRJ1jumpertothesettingsthatmatchyourCPUspeed,asfollow
table:
RJ1 1 2 3 4 RJ1 1 2 3 4
5on off on on 9off off on on
5.5 on off on off 9.5 off off on off
6on off off on 10 off off off on
6.5 on off off off 10.5 off off off off
7off on on on 11 on on on on
7.5 off on on off 11.5 on on on off
8off on off on 12 on on off on
8.5 off on off off 12.5 on on off off
Note: SOYO does not guarantee system stability if the user over clocks the
system. Any malfunctions due to over-clocking are not covered by the warranty.
Step 5. CPU FSB Setting (FJ1,FJ2)
For certain AMD  CPUs, the multiplier is not locked such that setting a multiplier higher
than specified on the CPU is possible. For technical details read the following:
However, the FSB Frequency can also be set through jumpers FJ1 and FJ2 and it may
therefore differ from the Frequency the CPU specifies. Doing so may however force your
CPU to operate out of its specifications and therefore SOYO can not guarantee the proper
functioning of your system.
Refer to the following table:
CPU FSB Setting FJ1 FJ2
200MHz Short Pin2-3 Short Pin2-3
266MHz Short Pin1-2 Short Pin1-2
123
123
123
123

SY-K7VTA PRO Quick Start Guide
12
Hardware
Installation
lVoice Doctor
Ifthesystemdoesnotboot-upproperly,theVoiceDoctorwillinformtheuserbyvoicethrough
internal/externalspeaker atwhatpointinboot-upsequencetheproblemarises.
Belowarethepossibleerrorstheusermayencounter:
1. TheProcessormightbedamageornotinstalledproperly
2. Thememorymodulemightbedamageornotinstalledproperly
3. VGAcardmightbedamageornotinsertedproperly
4. NoKeyboardconnected
5. DefectiveHD-Driver (IDE)
6. Floppymighthaveanerror
VoiceDoctorsupportstwo language,referthetablebelowonthelanguageyouprefer.
Voice Doctor’s
Language English Language Chinese Language
JP7Setting Short pin1-2 Shortpin 2-3
lCMOS Clear (JP5)
In some cases the CMOS memory may contain wrong data, follow the steps below to clear
the CMOS memory.
1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper
can be easily identified by its white colored cap.
2. Then put the jumper back to 1-2 to allow writing of new data into the CMOS memory.
CMOS Clearing Clear CMOS Data Retain CMOS Data
JP5Setting Shortpin 2-3for
atleast 5seconds to
clearthe CMOS
Shortpin 1-2to
retain new settings
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
123
123
123
123

SY-K7VTA PRO Quick Start Guide
13
Quick BIOS
Setup
3 3 Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The
[SOYO COMBO SETUP] combines the main parameters that you need to configure, all in
one menu, for a quick setup in BIOS.
Afterthehardwareinstallationis complete,turnthepower switchon,thenpress the <DEL> key
duringthe systemdiagnosticcheckstoenter theAwardBIOSSetupprogram.The CMOS
SETUPUTILITY willbeshownon thescreen.Then,follow thesestepstoconfiguretheCPU
settings.
Step 1. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 2. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT”menu and type “Y”at the prompt to load the BIOS
optimal setup.
Step 3. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue the boot
sequence.

SY-K7VTA PRO Quick Start Guide
14
The SOYO CD
4 4 The SOYO CD
The SOYO-CD will NOT autorunifyou useit onanOperating Systemother
thanWindows9x orNT.
Your SY-K7VTA PRO Motherboard comes with a CD-ROM labeled "SOYO CD." The
SOYO CD contains (1) the user's manual file for your new Motherboard, (2) the
drivers/software available for installation, and (3) a database in HTML format with
information on SOYO Motherboards and other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
If you use Windows NT, the SOYO-CD will not detect your motherboard type. In that case
the following dialog will pop up, please choose your motherboard and press OK. Now the
SOYO-CD Start Up Menu will be shown.
(SOYOCDStart UpProgram Menu)
If you use Windows 95 or 98, the SOYO CD Start Up Program automatically detects
which SOYO Motherboard you own and displays the corresponding model name.
7IWA-F
7IWA-F V1.0
6IWM/L
6IWM
6IWA
LI-7000
7IWB
7IWB V1.0
7IWM
7IWM/L V1
Please Select Your Board
OKCancel
X

SY-K7VTA PRO Quick Start Guide
15
The SOYO CD
The user's manual files included on the SOYO CD are in PDF (Postscript Document)
format. In order to read a PDF file, the appropriate Acrobat Reader software must be
installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 2. Install Drivers and Utilities
Click the Install Drivers button to display the list of drivers/ software that can be installed
with your Motherboard. The Start Up program displays the drivers available for the
particular model of Motherboard you own. We recommend that you only install those
drivers.

SY-K7VTA PRO Quick Start Guide
16
The SOYO CD
(DriverInstallation Menu)
A short description of all available drivers follows:
ØVIA 4in1 Driver Package for Win 9x/ME/NT/2k
The 4 in 1 Driver Package includes all drivers your motherboard needs. After selecting this
Driver Package, one driver will be installed automatically (the IRQ remapping utility), the
other three are installed if selected. By default all three drivers are selected. A description of
the 4 drivers follows:
 Bus Master PCI IDE Driver
This driver will speed up the data-transfer rate to and from the harddisk.
 AGPVxD Driver
This driver must be installed in order to be able to make use of the on-board AGP
Video functionality.
 VIAChipset FunctionsRegistry
This driver will make the necessary changes to the Windows registry, in order to
make sure that Windows has no problems recognizing your VIA chipset.
 IRQremappingutility(This driverisinstalled automatically)
This utility will remap the IRQ lines to make sure that everything functions properly
under Windows.
ØVIA Onboard Audio Driver for Win 9x/ME/NT/2000
You have to install the drivers before installing any application for the Onboard Audio.
ØK7VTAPRO VIA hardware(R) monitor for (Win 95/98)
Your motherboard comes with a hardware monitoring IC. By installing this utility
Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms
when current system values exceed or fall below pre-set values.
driverrevision:
VIA 4 in 1 Driver Package for Win 9x/ME/NT/2k
VIA Onboard Audio Driver for Win 9x/ME/NT/2000
K7VTAPRO VIA hardware(R) monitor for (Win 95/98)
CancelOK

SY-K7VTA PRO Quick Start Guide
17
The SOYO CD
Select which driver you want to install and click OK, or click Cancel to abort the driver
installation and return to the main menu.
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers
require to restart your system before they can become active.
Step 3. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to automatically find
the latest BIOS, manual and driver releases for your motherboard. This button will only
work if your computer is connected to the internet through a network or modem
connection. Make sure to get your modem connection up before clicking this button.
(*InternetExplorerisaMicrosoftTrademark)

SY-K7VTA PRO Quick Start Guide
18
Quick Trouble shoot tips
Video (no display) related issues
I built a new computer system using a Soyo board and nothing happens when
turning it on, no video and no beeps from the PC speaker. What is happening
and how can it be fixed?
No screen and no beeps mean that your CPU and motherboard do not work at all. It
could be that the CPU is not seated correctly or that a component on the M/B is
grounded (shorted) with the case. Also make sure to check the voltage setting
switch (110V/220V) on the back of the power supply. To isolate the problem do
the following:
1. Press and hold down on the “Ins”(insert) key while turning on the computer
until you get video. If you do not get video then,
2. Double-check jumpers setting on you motherboard and remove all add-on
cards, unplug all hard-disk and floppy-disk drive cables and see if you can hear
some beeps. If you still do not get any beeps, then try putting the motherboard on
the table (to isolate it from the case) with the CPU and speaker only, and give it one
more try.
I hear a series of beeps and I do not get anything from my monitor. What
could be wrong?
The following lists some basic beep codes and their possible meanings:
•One long beep and 3 very short beeps - The video card is not detected by
the motherboard. Please re-seat your video card. If you are using an AGP
card, please push your AGP card down real hard. You may have to push
VERY hard without the AGP card mounting screw. Make sure not to
insert the card the other way around.
•Continuous beeps –One or more of the memory modules is not seated
correctly in its socket.
My PCI VGA card works fine with my system, but when I put in a new AGP
card, it does not give me any video. Is my AGP slot bad?
This is a common problem with AGP video cards. The reason is that your AGP
card did not get seated into the AGP slot fully and firmly. Please push your AGP
card down into the socket real hard, it should snap twice. You may have to unscrew
the AGP card to allow the card to go further down. Do take care not to damage the
card by using too much force.

SY-K7VTA PRO Quick Start Guide
19
I get distorted video my AGP card right after I save my bios. Why is that?
The cause is likely that your AGP card is not running at the correct bus speed. To
fix this, please clear the CMOS via JP5 and if it still does not work, please upgrade
your motherboard bios to the latest version.
BIOS Issues
Where can I find the BIOS revision of my mainboard?
It will be displayed on the up-left corner on the screen during boot-up. It will show
as your board type followed by the revision number, such as 5EH_2CA1 (meaning
revision 2CA1 for the SY-5EH board) or 6BA+ IV_2AA2 which means SY-6BA+
IV motherboard with 2AA2 bios.
Where can I find the latest BIOS of my motherboard?
Please go to the technical support page of one of the SOYO websites (Taiwan:
www.soyo.com.tw), and look up your motherboard to find the latest BIOS
revision.
Hard disk, floppy drive, CD-ROM etc
When I boot up my new computer I got "floppy boot failure" and the LED on
the floppy stays on
Make sure the red wire of floppy ribbon cable goes to Pin1 on the floppy drive side
(don't trust the "key lock" or "notch") and use the end-connector of the cable (don't
use middle one).
Modem issues
I get an "I/O Conflict" message when I turn on my system and I can not get
my modem to work
What you need to do is to disable 'COM2' (or UART2 or serial port 2) in the bios
under integrated peripheral setup.
I have installed my modem drivers several times and I still cannot get my
modem to work. Why?
If you are sure that the modem driver has been installed correctly, then you need to
install the via 4 in 1 driver from the SOYO CD, this is because Windows does not
properly recognize relatively new chipsets.
I can not get my board to run properly.
Please make sure you have the latest bios and driver from the SOYO web site at:
http://www.soyo.com

SY-K7VTA PRO Quick Start Guide
20
How to contact us:
nIf you are interested in our products, please contact the SOYO sales
department in the region you live.
nIf you require Technical Assistance, please contact our Technical Support in
the region you live.
SOYO prefers Email as communication medium, remember to always add to the
email the country that you live in.
TAIWAN
SOYO COMPUTER INC.
No. 21 Wu-Kung 5 Rd., Hsin Chuang
City, Taipei Hsien, Taiwan, R.O.C
TEL: [phone]
FAX: [phone]
http://www.soyo.com/
Email:[email protected]
USA
SOYO INC.
41484 Christy Street, Fremont, CA
94538, USA
TEL: [phone]
FAX: [phone]
http://www.soyousa.com/
Email : [email protected]
GM
SOYO Deutschland GmbH
(SAAT Technology GmbH)
August-Wilhelm-Kuhnholz-Str. 15
D-26135 Oldenburg (Oldb), Germay
TEL: [phone]
FAX: [phone]
http://www.soyo.de/
Email: [email protected]
JAPAN
SOYO COMPUTER
SOYO BLDG, 1-23-14, Hyakunincho,
Shinjyuku-ku, Tokyo Japan 169-0073
TEL: [phone]
FAX: [phone]
http://www.soyo.co.jp/
Email: [email protected]
CHINA
GING MEI JEI LTD
Room 304, Phoenix Mansion, No. 165
Haidian Road, Haidian Distnct, Beijing
100080, China
TEL: [phone]
FAX: [phone]
http://www.soyo.com.cn/
Email: [email protected]
KOREA
SOYO TECHNOLOGY CO., LTD.
3 rd, F1, Wonhyo Bldg, 46-1,
Wonhyoro 3 Ga, yongsan Ku, Seoul
Korea
TEL: [phone]
FAX: [phone]
http://www.soyo.co.kr/
Email: [email protected]