SpaceLas CELEB 18 User manual

Please read this manual carefully before using the product
USER MANUAL
Laser show projector Celeb 18

2
Introduction
Thank you for purchasing this product. We always try to develop our
product with high-tech and high performance to meet your requirement and
exception.
The unit is designed strictly according to the international standard. The control way
is single or master-slave in option. The manual include the skill parameter and detail
instructions. Please read this manual carefully before using the product.
After reading it, please keep it in a safe place for future reference.
This unit has been tested at our factory before being shipped to you, there is no
assembly required.
Once after receiving this product, please take and put carefully. And check
cautiously that whether the product was damaged or not during the transportation.
Checking parts
Please check if the following parts are included:
1 x Light
1 x User manual
1 x Power cable
Danger Light Radiation!
Avoid direct eye exposure!
Light radiation can cause eye damage or skin damage
All protective measures for a safe operation of this light must be applied.

3
Installation
1. Please check the voltage whether is the same with the one showed on the
equipment or nor.
2. It must ask for the technical person and set the light safety when installation.
And let the light beam at the suitable angle.
3. When install this equipment please make sure there’s no flammable surface
(decorated things, etc.) within at least 2.5M and maintain minimum distance of
0.5M from the equipment to the walls.
4. Please make sure that there’s no other equipment or decoration materials
obstructed the exhaust fan and the vent-pipe when the equipment is working.
5. Products should be install immobility and try to avoid strong shake or hit.
6. In case of safety, it’s very important that to connect the earth with line.

4
Attention
1. Please do not open the bottom cover yourself without permission. Operate it
according the user manual. Call the technician when the machine breaks down.
2. Please do not see the light beam directly to avoid any damage.
3. Before connect or disconnect the power, please adjust the luminance of the diode
to the least to avoid any damage to the diode.
4. This unit should be keep dry, do not use in the rain and dusty environment. It can
be use in the outdoor with the water-proof cover projector.
5. Before connect power, check the plug is immobility or not, power cable should be
connect well.
6. Please do not open or close the equipment frequently that’s to avoid any effect to
the life span of the diode, and try the best to avoid long time working.
7. Due the the characteristic of the diode, after 4 hours working, it should be close at
least 25 minutes until the diode cooling then work again.
8. Don’t touch the light or draw the power cable when your hand was wet. And do
not pull the electronic power line.
9. Maintain the distance at least 3M above from the equipment to the object.
10. This equipment does not have any parts can repair for users, please do not open
the equipment.
11. When the diode become dim or damaged please contact he dealer timely.
12. When you want to re-transfer the products, you’d better use the original package
to shockproof.
Power supply and signal connection
1. Power supply
Connect the light to the main of the power supply with a dedicated plug, please
make sure the voltage should be the same with the one showed on the equipment.

5
It’s recommended that each fixture has an independent power switch to turn fixture
on or off at any time.
2. Signal connection
This device accept DMX512(1990) digital signal, master or slave can work in music
mode.
We provide circle 3-pin DMX cable to connect console and equipment. Please check
the following picture
TFT screen menu list as following
Menu First menu Secondary menu
DMX address 1 - 512
Auto in-play
Fast Beat ON/OFF
Medium Beat ON/OFF
Slow Beat ON/OFF
Animation ON/OFF
Music in-play
Fast Beat ON/OFF
Medium Beat ON/OFF
Slow Beat ON/OFF

6
Animation ON/OFF
SD card Mode
Repeat ON/OFF ONE / FILE / ALL
Music ON/OFF
Directory 1/8
File 1/48
Test Mode Image 1-3
System
Setting
Channel Setting 27CH /
52CH
Master / Slave
ON/OFF
Scan-safety ON/OFF
EASY ILDA ON/OFF
Language CH/EN
Sound Sense 0-100
About
Channel Num
Operational Mode
DMX Address
Case temperature
Running Time
Hardware version
Software version
Reset Setting
Master
Setting
Color RGB/G
Scan 15-40K

7
Brightness 0-255
Design
R Fade 0-255
G Fade 0-255
B Fade 0-255
Zoom 0-255
X Size 0-255
Y Size 0-255
Invert X ON/OFF
Invert Y ON/OFF
DMX Setting
Input DMX signal, and the link the DMX controller and the lights by the
control line as the following picture, you can control the lights by the
controller.
Any controller, each one must be its own address. The first light address
is set to 1, the second light address code is set to 28 or 53 (the first light
address 1 plus 27 or 52 channel), the third light on the 55 or 105.
DMX - 512 control mode as following :

8
Number Address LCD display(No.)
1 1 001
2 28 or 53 028 or 053
3 55 or 105 055 or 105
┇ ┇ ┇
Master-slave Setting
Link the lights as the following picture (the light which does not receive
signal, only output signal, will be the master light)，
Using before please must be check power supply link with earth
wire correctly.
The specification of the front and rear panel:
1. Input rated voltage
2. Fuse
3. Power switch button
4. Ground marking
5. DMX IN/ DMX OUT: DMX signal output and input

9
Specification
1. Rated voltage: AC 100V - 240V 50/60Hz
2. Power consumption: 100W
3. Color: □single color，□RGB
4. Modulation: analog
5. Scanner: 40kpps
6. DMX512 channel: 27CH/52CH
7. Control mode: music/ auto/ DMX512/ ILDA/ master-salve/ SD
card
8. Cooling requirements: air-cooled optimized airflow
9. Operating temperature: 0℃up to 35℃
DMX-512 channel
CH1=32-63, CH2 - CH27 or CH2 - CH52 valid
CH1=64-127, CH2, CH6 valid
Channel Parameter Value Parameter description
CH1
IPLAY mode
0～31 Black
32～63 Manual play
64～95 Auto play
96～127 Music play
SD mode
128～159 Manual play
160～191 Auto play
192～223 Music play (one file)
224～255 Music play (all files loop)
CH2 Dimmer 0～255 Fade 0% .... 100%
CH3 CH28 Red 0～255 Fade 0% .... 100%
CH4 CH29 Green 0～255 Fade 0% .... 100%
CH5 CH30 Blue 0～255 Fade 0% .... 100%

10
CH6 CH31 List 0～255 Each 32 value be 1 list，total 8 list
Macro each 64 value be 1 macro，total 4 macro
CH7 CH32 Cue 0～15 Black
16～255 Each 12 value be 1 cue, total 20 cues
CH8 CH33 X position 0～255 Left .... right（128 center）
CH9 CH34 X fine 0～255 X fine position
CH10 CH35 Y position 0～255 Down ....up（128 center）
CH11 CH36 Y fine 0～255 Y fine position
CH12 CH37 Rotation 0～255 Clockwise rotation (0°-360°)
CH13 CH38 Fine rotation 0～255 Fine rotation
CH14 CH39 Zoom 0～255 100%....0%
CH15 CH40 X flip 0～255 Left...right
CH16 CH41 Y flip 0～255 Down ... up
CH17 CH42 Color
0～7Default
8～15 White
16～23 Red
24～31 Yellow
32～39 Green
40～47 Cyan
48～55 Blue
56～63 Purple
64～127 Each 8 value be 1 color effect，total 8
128～143 Macro 1
144～159 Macro 2
160～175 Macro 3
176～191 Macro 4
192～207 Macro 5
208～223 Macro 6

11
224～239 Macro 7
240～255 Macro 8
CH18 CH43 Write in 0～255 Visible point 100%-0
CH19 CH44 Deformation
0～15 Invalid
16~31 Macro 1（valid for 14CH 25CH ）
32~47 Macro 2（valid for 14CH 25CH ）
48~63 Macro 3（valid for 14CH 25CH ）
64~79 Macro 4（valid for 14CH 25CH ）
80~95 Macro 5（valid for 14CH 25CH ）
96~111 Macro 6（valid for 14CH 25CH ）
112~127 Macro 7（valid for 14CH 25CH ）
128~143 Macro 8（valid for 14CH 25CH ）
144~159 Macro 9（valid for 14CH 25CH ）
160~175 Macro 10（valid for 14CH 25CH ）
176~191 Macro 11（valid for 14CH 25CH ）
192~207 Macro 12（valid for 14CH 25CH ）
208~223 Macro 13（valid for 14CH 25CH ）
224～255 Default
CH20 CH45 Wave
0 Invalid
1～39 Macro 1
40～79 Macro 2
80～119 Macro 3
120～159 Macro 4
160～199 Macro 5
200～255 Macro 6
CH21 CH46 Write in
0 Invalid
1～42 Macro 1
43～84 Macro 2
85～126 Macro 3

12
Strobe 127～255 Slow... fast
CH22 CH47 X position
0 Invalid
1～32 Macro 1
33～64 Macro 2
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
CH23 CH48 Y position
0 Invalid
1～32 Macro 1
33～64 Macro 2
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
CH24 CH49 Z rotation
0 Invalid
1～32 Macro 1
33～64 Macro 2
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
CH25 CH50 Zoom
0 Invalid
1～32 Macro 1
33～64 Macro 2

13
SD card 20CH
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
CH26 CH51 X flip
0 Invalid
1～32 Macro 1
33～64 Macro 2
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
CH27 CH52 Y flip
0 Invalid
1～32 Macro 1
33～64 Macro 2
65～96 Macro 3
97～128 Macro 4
129～160 Macro 5
161～192 Macro 6
193～224 Macro 7
225～255 Macro 8
Channel Parameter Value Parameter description
CH1 IPLAY mode 0～31 Black
32～63 Manual play

14
64～95 Auto play
96～127 Music play
SD mode
128～159 Manual play
160～191 Auto play
192～223 Music play (one file)
224～255 Music play (all files loop)
CH2 Dimmer 0～255 Brightness 0% .... 100%
CH3 Red 0～255 Brightness 0% .... 100%
CH4 Green 0～255 Brightness 0% .... 100%
CH5 Blue 0～255 Brightness 0% .... 100%
CH6 List 0～255 Each 32 value be 1 list，total 8 list
Macro each 10 value be 1 macro，total 25 macro
CH7 Cue 0～15 Black
16～255 Each 12 value be 1 cue,total 20 cues
CH8 X position 0～255 Left .... right（128 center）
CH9 X fine 0～255 X fine position
CH10 Y position 0～255 Up ....down（128 center）
CH11 Y fine 0～255 Y fine position
CH12 Rotation 0～255 Clockwise rotation (0°-360°)
CH13 Fine rotation 0～255 Fine rotation
CH14 Zoom 0～255 100%....0%
CH15 X flip 0～255 Left...right
CH16 Y flip 0～255 Down ... up
CH17 Color
0～31 Default
32～63 White
64～95 Red
96～127 Yellow
128～159 Green

15
Auto in-play mode
In LCD display, UP/DOWN to select “Auto In-play”, Fast Beat, Medium Beat, Slow Beat
and Animation for option
Music in-play mode
In LCD display, UP/DOWN to select “Music In-play”, Fast Beat, Medium Beat, Slow
Beat and Animation for option
SD card play setting
1). SD card with 8 fixed folders, each folder with 48 files(.ild). Select ALL, repeat play
all the SD card file. Select ONE, repeat play one file in the folder.
2). The content of SD card can be played by console
1). In SD card, you can find 8 folders, folder naming rule as following
160～191 Cyan
192～223 Blue
224～255 Purple
CH18 Write in 0～255 Visible point 100%-0
CH19 Speed
0～15 Default
16~31 Pause
32~255 25% - 200%
CH20 Scan rate
0～31 Default
32～223 6k - 29k
224～255 30k

16
2). Add file (.ild) to folder, (note:file name could be number or letter, and should
not exceed 32 letters) as following
3). Folder and content play sequence as following
The files in folder will be played in the order in which the files are copied to the SD
card. That is, the first copied, first play. If you want to change the play sequence, you
can copy them in the sequence you want. The folders will be played according to the
fixed folder number(From LF001 ...LF008) in the sequence of copying.

17
Master-slave mode
Master
In LCD display, UP/DOWN select “system setting”, master/slave ON
Slave
In LCD display, UP/DOWN select “system setting”, master/slave OFF, set “DMX
address” as 001
ILDA mode
ILDA signal prior, connect ilda cable, no need any setting. RJ45 connector, connect
our ILDA box, LCD display, UP/DOWN select” system setting”, “EASY ILDA” ON
Maintenance
Maintenance should be performed every 3 month, different period according to the
environment. Use a sponge which is dipped with alcohol, rather than wet cloth or
other chemical liquid, to clean the mirror.
Always disconnect from the power before maintenance .
Warning
Do not look at the light source directly. Power must be disconnected before install
and maintenance.
Declaration
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and the warning note written in his user manual.
We cannot be made liable for damages caused by incorrect installations and
unskilled operation!

18
Product common breakdown comparison table
breakdown cause Major breakdown analysis and solution
The fixture no light or
no work
1.Check the power cable whether to connect the fixture,
whether the fuse does bum out.
2.Check the input voltage whether to assign the voltage
match with the fixture.
No sound control
1.Check the address code or the display whether
establishes according to the instruction booklet is the voice
control pattern.
2.Check the potentiometer possibly moves is smallest，
attempt to adjust the potentiometer.
The fixture can bright
normally, but it not
controlled by controller
1. Please check the fixtures’ DIP outset address setting
whether correctly.
2.Please check the XLR signal cable whether be damage.
Master-slave mode, the
master mode is normal,
but slave mode is not
normal
1.Please conformed only one for the master and the master
without DMX be connected, and to set master as sound
control or auto pattern.
2.If the Master-slave setting is right but still have problem,
please check the XLR connect cable.
The button malfunction,
does not work.
1.Check the buttons whether to have some button not to
have the normal reset.
The fixtures’ brightness
obvious dim
1.Check the LED tubes or the light already whether to be
service life.
2.Check the internal and external optical system whether
to be clean.
If above method cannot eliminate the fault, please consult the dealer.