Spacio Innovations WEXSTAR EWT-009 User manual

Programmable Thermostat Wi-Fi
User Manual
Ⅰ. Technical Data
1. Power Supply: AC100~120V 50/60Hz
2. Maximum load: USA 1440W/12A
3. Wireless standard: IEEE802.11b/g/n
4. Frequency range: 2.412~2.484GHz
5.Security mechanism: WEP/ WPA-PSK/ WPA2-PSK
6. Encryption type: WEP/TKIP/AES
7. Standby power consumption: <0.8W
8. Working environment: temperature -5~50° C;
humidity 10% -95%
9. Size: L110mm*W56mm*H78mm
10. Unit net weight: 130g
Ⅱ. Product Description
This Programmable Thermostat Wi-Fi can be used with
Wexstar heaters, to be controlled by mobile phone,
function includes:
● WIFI remote control
● Adjust temperature
● Weekly programmable
● Count down
● Group control
● Share to other users
Ⅲ. WIFI Pair Instructions
1. Connect your phone to WIFI（2.4GHz network ).
2. Scan and install below Smart Life APP, and Register
an account. Smart Life App Icon
3. Plug the Programmable Thermostat Wi-Fi into a
socket and hold the button 5-10 seconds UNTIL the
indicator is blinking.
NOTE: same operation needed when WiFi hotspot changed,
WiFi password changed, or cell phone changed.
4. Click Smart Life App to enter main interface, select
room name and click “Add Device” or the upper
right corner “ ○+” icon. A pop-up window
appears as below picture.
5. Click “Go to add”. In next page click“○+”to add a
Bluetooth device, and a Enter Wi-Fi Password
dialog will pop-up as following.
6. Enter Wi-Fi password, click“Confirm”，It will
automatically enter the next step for Wi-Fi
connection. The device will be added successfully
after waiting for 20-30 seconds. And meantime the
red indicator on the thermostat lights up. You can
name this device, e.g. “Infrared panel heater”.
Note: If the connection is timed out in Step 6, please
unplug the Thermostat Wi-Fi from power socket for
10 seconds, and then Repeat Step 3-6.
Edit device
Back to main
interface
Device Name
Device Status
Power On/Off
Temperature
Setting
Weekly programming
Countdown
°C/°F Converter

Ⅳ. Operation Instructions
1. Main interface of the Smart Life APP after thermostat
connected successfully is as below.
2. Click the green switch (in main interface) to
turn on/off the power supply of the heater, the indicator
light color is blue, blue light up means the thermostat has
been powered on. You can also press the button of the
thermostat to turn on/off, and meantime the color of this
icon in theAPP will change accordingly.
3. Click device name “infrared panel heater” to enter the
interface of the thermostat.
4. means turning on/off the power supply. Setting
temperature should be also at least 0.5 ℃ higher than
room temperature to make the heater work.
5. means weekly programming mode. Under
weekly mode, users can program the heater to change the
operation and desired temperature throughout the week.
ON and OFF timing is separate, you need to add
individually. Don’t forget to turn ON the weekly button
to Green after programming.
6. is countdown function for setting to power off
the thermostat.
7. means convert temperature display between ℉
and ℃. NOTE: weekly, Timer and TEMP these three functions
can be edit only under power on mode!
8. means other editing of the thermostat,
description as below
1) Device name: edit the thermostat name.
2) Device information: to check the virtual ID etc.
device information.
3) Share device: you can share the control of this
thermostat to other mobile numbers/email addresses
if they have been registered in “Smart Life” APP.
4) Create Group: you can group different thermostats
to control together.
5) FAQ & Feedback: to report any problems to the APP
supplier.
6) Check Device network: check the Wi-Fi connection
status of device.
7) Check Update: Get latest firmware version.
8) Remove Device: remove thermostat from your APP.
V. Important notes
1. Thermostats only can be paired under 2.4GHz
network.
2. Red light means the thermostat is online, blue light
means the heater is powering on.
3. If unplug the thermostat 4 times or more and each time
shorter than 5 seconds, internal Wi-Fi connecting
information will be cleared, you need to pair the
thermostat with Wi-Fi again.
4. Wi-Fi or network disconnected will cause thermostats
offline and heater powering off.
5. The blue LED indicator of the thermostat may not light
up at the first time when you finished the WIFI
connecting, you need to wait for a couple of seconds
due to network searching and connecting.
6. The setting temperature should be at least 0.5 ℃
higher than room temperature in order to power on the
heater.
7. The temperature sensor of device is at the bottom of
the plug, do not cover or put the thermostat where
there will be heat, and better to make the temperature
sensor down while you plug the thermostat into wall
socket.
8. Do not use this thermostat in wet or running water
environment.
9. Please pull out the thermostat from power socket if
long time no use.
10. The thermostat can be used with any Wexstar heater
from 350W up to 1,100W. It can also be used with
other heating devices that support a Max. Load of
1440W/12A
•C TUV US certification Number CU 72227711
•FCC-ID number 2A7RI 13EA2A7RI
Contact us:
Spacio Innovations Inc.
Email: [e-mail]
www.spacioinnovations.com