Spear & Jackson TA-COMP70 User manual

Instruction Manual
2.5HP 50 Litre
Belt Drive
Air Compressor

Introduction 3
Environmental Responsibilities 3
General Safety Instructions 3
Electrical Safety 4
Use of Extension Cords 4
Additional Safety Instructions 4-5
The Compressor & Its Components 5
Assembly & Operating Instructions 6
Automatic On/Off Switch 7
Overload Protection / Reset Procedure 7
Pressure Gauges 8
Pressure Regulator 8
Safety Valve 8
Compressor Set-Up 8
Shutting Down Your Compressor 9
Maintenance 9
Trouble Shooting 9
Exploded Diagram 10
Parts Listing 10
Supplier Contact Details 11
Warranty Details 12-13
2
Index

Introduction.
Project Air Compressors have been manufactured under stringent Quality Standards to meet the
performance criteria set by Spear & Jackson.
After familiarization you will find this compressor both easy and safe to operate.
Read the instruction manual completely before using your new Spear &Jackson Air
Compressor.
These compressors have many features which will make your work faster and easier.
Please ensure all waste and unwanted products and are disposed of in a safe and
environmentally friendly manner.
Environmental Responsibilities.
When using this product, basic safety precautions should always be followed:
DO NOT OPERATE A COMPRESSOR WHEN UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.
1. Read all instructions prior to using the product.
2. To reduce the risk of injury, close supervision is necessary when the compressor is in use
near children or infirm persons.
3. Know how to stop the compressor and be able to reduce the pressure immediately.
4. Be completely familiar with all the controls.
5. Please secure or cover any long hair, clothing or jewelry prior to using this compressor.
6. Do not reach over machines with moving parts when in operation.
7. Please ensure that any potential trip or slip hazard is removed prior to operating this
compressor.
8. Do not use the compressor if the power cord shows any signs of damage or wear. Repair or
replace the damaged cord before use.
9. Do not pull forcefully on the cord to disconnect it from the power point.
10. Keep the cord away from heat sources, oil and sharp edges.
11. NEVER move the unit by pulling on the air hose. Use the handle provided at the front and on
the rear of the tank.
12. Please ensure that the work area is well lit, ventilated and clean and tidy.
General Safety Instructions
3

Warning !
To reduce the risk of electrocution keep all connections dry and off the ground. Do not use if wet or in a
wet environment.
This product should only ever be connected to a properly manufactured, fitted and earthed power
outlet that complies with National and regional electrical authority regulations and requirements.
Extension cables or generators are not to be used with this product, as it may cause damage to
the Compressor. Such actions will void the warranty. Please use a longer Air Hose.
Electrical Safety Instructions
Additional Safety Instructions
1. Always wear ear and eye protection when using any compressor, air tool or power tool, or
are in the vicinity of the product when it is use.
2. Do not use the compressor in areas near combustible materials, combustible fumes or dust.
3. Always use a respirator or mask when spray painting or whenever there is a possibility
vapors may be inhaled.
4. DO NOT ALLOW CHILDREN TO OPERATE THE COMPRESSOR AT ANY TIME.
5. DO NOT MAKE ANY MODIFICATIONS OR ADJUSTMENTS TO THE UNIT OR ANY OF ITS
COMPONENTS.
7. UNITS WITH BROKEN OR MISSING PARTS OR WITHOUT THE PROTECTIVE HOUSING
OR COVERS SHOULD NEVER BE OPERATED.
8. Do not leave the compressor unattended while the pressure switch is in the “I” (on)
position.
9. Do not add or change oil while the compressor is in operation.
10. Use only the supplied or recommended lubricating oil for the compressor. Spear & Jackson
Compressor Oil is available from Bunnings Stores (Product Code CA-CAP721-04).
Recommended viscosity ISO 0046.
11. This compressor is fitted with a pressure activated “On/Off” switch. When the switch is in the
“on” position, the compressor may start operating at any time when the pressure in the tank
falls below the preset level of the pressure switch.
12. When not in use, we recommend that all tools and hoses be disconnected and the tanks
drained of air and moisture. We also recommend that you leave the tank drain open when
the compressor is not in use.
13.To reduce the risk of fire or explosion, never spray flammable liquids in a confined area.
4

14.Do not ever directly inhale compressed air. Serious injury could occur.
15.Do not use the air from the compressor for any re-breathing apparatus.
16.Never apply the outlet air of this compressor directly on to any part of a person’s body. Do not
attempt to block the air outlet with your finger or any part of your body. Severe injury may
occur.
17.Do not weld anything to the air tank of the compressor. This could result in tank failure and will
void the warranty.
18. Do not operate the compressor with the shield, cowling or cover removed.
19. Before transporting the compressor it is recommended that the tank be drained of pressurized
air.
20.Spear & Jackson Australia Pty Ltd will not be responsible for any damage or injury resulting
from cases of misuse or negligence.
21.Spear & Jackson Australia Pty Ltd will not be liable for any changes made to the compressor nor
for any damage resulting from such changes.
22. This air compressor is a duty cycle tool. It is not designed to run 100% of the time. If
it is run on a continuous basis this may result in overheating or activation of the
thermal cut out. This compressor should not run for more than 40 minutes in every
hour. Continual use will void the warranty
Additional Safety Instructions
Warning !
In the event that an air line is cut or broken, the air supply must be turned off at the
compressor.
The Compressor and Its Parts
5
Air Filter
Oil Fill Cap
Belt Safety
Guard
Electrical Reset
button
Handle
Pump
Motor
Wheels Wheels
Tank Drain
(underneath)
Pressure
Switch
Regulator
Air Outlet
Pressure Relief Valve

Assembly & Operating Instructions
2. The unit is supplied with oil already in the pump. Please add sufficient oil from the bottle
supplied until the marker in the sight glass is level with the red indicator line.
Additional oil can be purchased from Bunnings if required
(Spear & Jackson Compressor Oil CA-CAP721-04).
Sight Glass
Empty Sight Glass
Over full Sight Glass Correct Level
8. Before connecting the compressor to the power outlet, check for broken components
and any damage to the power cord.
6
1. The compressor is supplied with wheels, axles and a handle. Please remove unit from the box
and check for any damage. Please attached the handle and the wheels using the hardware
provided.
9. Make sure the pressure switch is in the “O” or OFF position.
When Red lever is UP compressor is OFF
10. Plug the unit into a properly fitted and earthed power outlet.
11. Attach the desired tool to the end of the air hose.
12. Switch the compressor on by lifting the red knob on the top of the pressure switch.
When Red lever is DOWN compressor is ON

Automatic On / Off
The compressor is equipped with a pressure activated on/off switch. The compressor will only
run when the switch is in the “I” or ON position (as per previous page).
Once the tank has reached the maximum preset pressure (125 PSI), the pump will
automatically shut off.
The pump will automatically restart once the pressure in the tank drops below the minimum
preset pressure (100 PSI).
The maximum and minimum pressures are set at the factory. Any attempt by the
operator to change them will void the warranty of the product.
Overload Protection / Reset Procedure
1. Switch “On/Off” Switch to “Off” Position.
2. Disconnect compressor from Power source.
3. Press the reset button located on the electrical box on top of the motor.
(As shown below)
4. Reconnect to power source.
5. Re activate compressor using the “On/Off” Switch.
Reset switch located here
Possible causes of motor overload are as follows -
1. Inadequate power supply.
2. Use of extension leads.
3. Overheating.
4. Lack of lubricating oil.
5. Use outside the standard operating parameters for this compressor.
7

The Tank Pressure Gauge supplies the reading of the air pressure inside the tank.
Pressure Gauges
NOTE. If you do not allow the air to discharge whilst you are setting the regulator, the pressure
as indicated on the regulated outlet gauge will be incorrect.
This gauge ONLY indicates the correct pressure while air is being discharged from the
outlet.
This compressor is fitted with an Air Pressure Regulator. It allows regulation of the output air
pressure.
Some air tools require a higher operating pressure than others. Please refer to the air pressure
requirements of your tools for the proper settings for the regulator.
Pressure Regulator
The compressor is equipped with a safety valve that will engage when the pressure in the
tank exceeds the maximum pressure setting, releasing any excess built up.
DO NOT REMOVE OR ATTEMPT TO ADJUST THE SAFETY VALVE.
Safety Switch
Safety Valve
Compressor Set Up
8

When you have finished using your compressor, follow these steps:-
1. Close the air outlet taps.
2. Switch off the compressor.
3. Disconnect unit from power outlet (power point).
4. Disconnect tools and / or Accessories from the air hose.
5. Disconnect the Air Hose.
6. Locate the drain valve on the underside of the tank.
7. Open the drain valve to release remaining pressurized air from within the tank. Moisture build
up in the tank is normal with air compressors, so a small amount of water may come out
while draining. (Draining the tank is vital for the longevity and safety of your air
compressor).
8. Store the compressor in a cool, dry place.
Shutting Down Your Compressor
1. The tank will require accumulated moisture to be drained from it on a regular basis. It is
recommended that the tank be drained of moisture after every 5 Hours of use. The drain
valve is located on the underside of the tank.
2. Check Oil level before each use.
3. Wash air filter insert in a mild soapy solution after 50 hours use. Operation in extreme
conditions e.g., dust, paint residue etc, may require more frequent cleaning.
4. Check handle is attached properly prior to use.
6. Check power cord for signs of wear and tear before each use.
7. Never use caustic agents to clean any part of the compressor.
8. Remove dust and dirt regularly. Wipe down compressor with a damp rag. Do not use alcohol,
petrol or other cleaning agent as this presents a fire hazard.
Maintenance
9
Trouble Shooting
Problem Probable Cause Possible Solution
Not connected to power supply Check Connection
Power supply not switched on Check switched On
Tank full of air Motor will restart when pressure drops below preset minimum
On/Off switch in Off position set switch to "on" position
Problem Probable Cause Possible Solution
Power Fault or supply voltage too low Check the Power supply
Power cord too long or too thin Do not use extension leads
Lack of lubricating oil Check oil level and adjust as necessary
Compressor running non stop. Reduce air consumption and allow compressor to cool.
Problem Probable Cause Possible Solution
Loose Part Tighten Component
Wheel or mounting feet loose Tighten Component
Problem Probable Cause Possible Solution
Dirty air filter Clean air filter
Air Leaking Return to point of purchase for assessment
Air consumption beyond capability of the unit Reduce air consumption.
Problem Probable Cause Possible Solution
Oil Level too high Maintain the oil at the correct level
Oil filler hole blocked Check and clean
Incorrect grade of oil used Use recommended oil only
Inability to maintain required
operating pressure
Oil Consumption too high
Motor will not run
Motor Running too slow
Motor becoming excessively
hot
Compressor will not start
Excessive vibration or noise

10

11
Warranty
Responsibilities under this warranty:
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
The benefits of this warranty are in addition to any rights and remedies imposed by
Australian State and Federal legislation that cannot be excluded.
Warranty
Warranty Period: One Year from the date of purchase
Warranty Provider: Spear & Jackson Pty Ltd ("Spear & Jackson")
PO Box 4400 Dandenong South
Victoria Australia 3164
Telephone: [phone]
Facsimile: 1300 735 858
Email:[email protected]
What is covered under this Warranty: Spear & Jackson warrants that your
Air Compressor ("Product") will be free from substantial defects due to
material and workmanship during the warranty period.

Warranty
12
What is not covered under this Warranty
1. Any failure that results from an accident, purchaser’s abuse, neglect or
failure to operate Product in accordance with instructions provided in the
owner’s manual(s) supplied with the Product.
2. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
3. Items or service that are normally required to maintain the product, i.e.
lubricants, filters and gaskets, etc.
4. Any failure caused by installing or operating the Product under conditions
not in accordance with installation and operation guidelines or damaged by
contact with surroundings.
5. Pump or valve wear or failure caused by rain, excessive humidity,
corrosive environments, oil contamination or other contaminants.
6. Cosmetic defects that do not interfere with Product functionality.
7. Damage due to incorrect voltage or improper wiring to which the Product is
connected.
8. Other items not listed but considered general wear parts.
9. Pressure switches, air governors and safety valves modified from factory
settings.
10. Damage caused by use of incorrect oil.
11. Damage from inadequate filter maintenance.
Responsibilities under this warranty:
Warranty Provider: To repair or replace, at Spear & Jackson option, any
Product or component which is defective, has malfunctioned and/or failed to
conform due to defective material or workmanship within duration of the
warranty period.
Spear & Jackson reserves the right to replace defective parts of the Product
with parts and components of similar quality, grade and composition where an
identical part or component is not available.
Goods presented for repair may be replaced by refurbished goods of the same
type rather than being repaired. Refurbished parts may be used to repair the
goods.
Purchaser:
Retain dated proof of purchase and maintenance records. Use reasonable care
in the operation and maintenance of the products as described in the owner’s
manual(s).

Other Limitations:
This warranty is not transferable to a subsequent customer if you sell it during
the warranty period.
Spear & Jackson makes no express warranties or representations other than set
out in this warranty.
The repair or replacement of the product or a component of the product is the
absolute limit of Spear & Jackson's liability under this express warranty.
Notices
With continuing product development changes may have occurred which render
the product received slightly different to that shown in this instruction manual.
Spear & Jackson reserves the right to change Product specifications without
notice.
Note: Specifications may differ from country to country.
13
Warranty
Before returning this product for a Warranty Claim or any other reason
Please Call: 1300 731 818 (Australia)
0800 652 652 (New Zealand)
The Helpline operates from 8am to 7pm, 5 days a week (EST).
This allows you to contact Spear & Jackson directly with any queries and
technical questions you have regarding our products.
When you make your call, please have the following information at hand:
Product Type
Product Code
Place of Purchase
Date of Purchase
Concise description of the problem
A Spear & Jackson Customer Service Officer will take your call and, in most
cases, will be able to solve your problem over the phone.
If the Spear & Jackson Customer Service Officer is unable to solve the problem,
and you wish to make a warranty claim, you must make the Product available
to Spear & Jackson for inspection and testing. If such inspection and testing
finds no defect in the Product, you must pay Spear & Jackson's usual costs of
service work and testing.
You must bear the cost of the transport of the Product to and from Spear &
Jackson to make the warranty claim, and all insurance of the Product.