Speco O4B2M User manual

i
Quick Start Guide
4MP Bullet IP Camera
O4B2M

ii
Welcome
Thank you for purchasing this network camera!
This owner’s manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.

iii
Important Safeguards and Warnings
1 ．
．．
． lectrical safety
All installation and operation here should conform to local electrical safety codes.
se a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in
device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2 ．
．．
． nvironment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and
installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small
quantity of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as
using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the
camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use,
please refer to the following methods if dirt is found:
Stained with dirt
se oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
se oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward.
Change the cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.

iv
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the
right to modify these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the
package.
Accessory Name Amount
Network Camera nit 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1

v
Table of Contents
1 Structure .................................................................................................................................. 1
1.1 External Cable ............................................................................................................. 1
1.2 Dimensions ................................................................................................................. 2
1.3 Alarm Setup ................................................................................................................ 2
2 Device Installation .................................................................................................................... 4
3 IP Scanner ................................................................................................................................ 6
3.1 Operation ................................................................................................................... 6
4 Web Operation......................................................................................................................... 7
4.1 Login and Main Interface ............................................................................................ 7

1
1Structure
1.1 xternal Cable
Note:
You can refer to the following figure for cable information. See Figure 1-1 .
Figure 1-1
Please refer to the following sheet for detailed information.
No. Port Name Function Connector Note
1 A DIO O T Audio output port RCA Output audio signal to speaker
2 A DIO IN Audio input port RCA Input audio signal
3 LAN Network port Ethernet port Connect to standard Ethernet cable.
Supports PoE.
4 I/O I/O port - Alarm signal input/output.
5 Power Power input port - Power port. Input DC 12V
Please refer to the follow sheet for detailed pin information.
Port Name SN Name Note
I/O Port
1 ALARM_NO
Alarm output port.
NO: normally open alarm output port.
It must be used with ALARM_COM.
2 ALARM_COM Alarm output public port.
3 ALARM_IN1 Alarm input port 1. It is to receive the on-off signal from the
external alarm source.
4 ALARM_IN2 Alarm input port 2. It is to receive the on-off signal from the
external alarm source.
5 GND Ground port

1.2 Dimensions
Note:
Please refer to the following figure for dimension information. The unit is mm. See
1.3 Alarm Setup
Alarm input, output description:
Step 1 Connect alarm input device to the alarm input of
Step 2 Connect alarm output device to the alarm output of
collector circuit
which connects 10K resistor to 3.3V externally.
Step 3 Open the web viewer and
set
alarm signal, the
alarm input device will generate high and low level
corresponding type to NO or NC
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.
Please refer to the following figure for dimension information. The unit is mm. See
Figure
1
Figure 1-2
Figure1-3
Step 1 Connect alarm input device to the alarm input of
the I/O cable.
Step 2 Connect alarm output device to the alarm output of
the I/O cable. A
larm output is
which connects 10K resistor to 3.3V externally.
set
the
alarm input and output correspondingly. When
alarm input device will generate high and low level
signals. Set
the
corresponding type to NO or NC
.
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.
1
- 2.
larm output is
an open
alarm input and output correspondingly. When
there is an
the
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.

3
Please refer to the following figure for alarm input information. See Figure 1-4.
Alarm input: When the input signal is idle or grounded, the device can collect the different status of the
alarm input port. When the input signal is connected to 3.3V or it is idle, the device collects logic “1”.
When the input signal is grounded, the device collects logic “0”.
Figure 1-4
Please refer to the following figure for alarm output information. See Figure 1-5
When alarm output is OC, it needs to increase pull-up resistance externally to work normally; output
signal is high and low level. After external pull-up resistance is increased, the default of output signal is
high level, and it switches to low level when there is alarm output.
The working current of alarm output port is recommended as <= 10mA. The max current which is used to
drive the external circuit is 80mA and it is advised to add a relay if it is beyond the value.
Figure 1-5

4
2Device Installation
Note:
 Before installation, please make sure the installation surface can support a minimum of 3 times the
weight of the camera
Figure 2-1
Please see Figure 2-1.
Step 1
Stick installation position template to designated surface where you will install the device (wall or ceiling).
Step 2
Drill holes according to the position of the holes marked on the installation template.
Step 3
Insert the expansion bolts into the holes you just drilled.
Step 4
Take out and tighten the screws to fix the device on the installation surface (wall or ceiling). You can
move the sunshade back and forth. When you have fixed the device, you must tighten the sunshade.
Step 5
Plug external wiring of the device properly.

5
Figure 2-2
Please be sure to loosen the adjusting screw when adjusting the device position and angle, tighten the
adjusting screw after adjustment.
Continuous rotation towards the same direction for the camera body has to be within 3 circles.
Step 6
se screwdriver (in accessories bag) to loosen adjusting screw.
Step 7
Adjust the device in all possible directions, and set its monitoring direction.
Step 8
se screwdriver to tighten the screws.

3IP Scanner
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
3.1 Operation
Open up IP Scanner.
Error! Reference source not found.
In the device list, you can view the IP address, model number, and MAC address of each device. Select
the applicable device and double click
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
Error! Reference source not found.
In the device list, you can view the IP address, model number, and MAC address of each device. Select
the applicable device and double click
to open up the web viewer.
Figure 3-1
In the device list, you can view the IP address, model number, and MAC address of each device. Select

4Web Operation
This device supports viewing and management via a web browser on a PC.
4.1
Login and Main Interface
Open the browser and input network camera address in the address bar or double click the device in IP
Scanner. See Figure 4- 1.
The login interface is shown as below. See
Please input your user name and password.
Default user name is admin
and password is
Note: For security purposes, please change the password after initial login.
After logging in, follow directions to install applicable plugins.
This device supports viewing and management via a web browser on a PC.
Login and Main Interface
Open the browser and input network camera address in the address bar or double click the device in IP
Figure 4- 1 IP address
The login interface is shown as below. See
Figure 4- 2.
Please input your user name and password.
and password is
1234 .
Note: For security purposes, please change the password after initial login.
Figure 4- 2 Web login
After logging in, follow directions to install applicable plugins.
Open the browser and input network camera address in the address bar or double click the device in IP
Input your IP
address
here