Speco HT-647HRTP User manual

HT-647HRTP
540 Line Color Dome Camera
Wall & Ceiling Mountable
Chameleon Cover Included
Please read this manual thoroughly before operation and keep
it handy for further reference.

PACKAGE CONTENTS
•Please make sure that the following items are included
in the package:
1 HT-647HRTP Camera
4 Mounting Screws
1 Chameleon Dome Cover
1 Video Test Lead
Please leave this manual with the end-user for future
reference.
1

PRECAUTIONS
This dome camera should be only installed by qualified
personnel
To prevent a fire or electrical hazard please use proper power
cable
The dome cover should be treated with care
Do not clean the cover with an abrasive cleaning material-
please use a soft cloth or tissue to clean the dome cover
There are no user-adjustable parts inside. Please do not
disassemble this camera other than to make initial
adjustments.
Please use a UL approved regulated 12-volt DC power supply
Please use appropriate low voltage power cable to prevent fire
or electrical shock.
Please insure that your installation area can support the
weight of the camera.
Please handle this camera carefully:
- Don’t use a strong or abrasive detergent when
cleaning the camera.
- Don’t expose the camera to direct sun
2

CAMERA INSTALLATION
Connections :
1. Apply 12-Volts DC ( constant voltage 300mA or better)
-CONNECT POWER TO THE POWER JACK.
2. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
YELLOW:VIDEO OUT
POWER SUPPLY
CONNECT
POWER INPUT:RED
CENTER:(+)
3

CHAMELEON DOME INSTALLATION
3. If desired, place the Chameleon Dome over the HT-647HRTP
* Spray the Chameleon Dome with your desired color
* If necessary apply a second coat
* Painting method on Chameleon Dome
●Notes : If painting is desired, please do so before installation
Push the Chameleon Dome over the HT-647HRTP until it snaps into
position.
4

Features
SLC
When the image is in front of strong background lighting,
your camera allows you to get the clear image.
INTENSIFIER
1/3 inch density CCD and digital processor permit
high quality pictures to be captured in very low light
condition.
High Resolution
Horizontal resolution of 540 TV lines is
achieved by using a SONY Double Speed CCD with
410,000 pixels, yielding pictures with a high S/N ratio..
Motion Detection
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
5

OSD
All camera functions are menu driven for easy use.
Dynamic Noise Reduction
The Intensifier camera has a DSP chip that can
remove image noise efficiently showing clean
images in low light conditions.
ELECTRONIC DAY/NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
The Intensifier camera will work with auto iris, manual iris and
fixed iris lenses.
MANUAL / AUTO IRIS LENS
6

Operating your camera
OSD Function
LENS OPTION
●DC ●MANUAL
SETUP MENU
SHUTTER
●OFF ●F/L ●MANUAL
WHITE BALANCE
●ATW ●AWC MANUAL●
BACKLIGHT
●OFF ●LOW ●MIDDLE ●HIGH
AGC
●OFF ●LOW ●MIDDLE ●HIGH
DNR
●OFF ●LOW ●MIDDLE ●HIGH
SENSE UP
●AUTO ●OFF
NEXT PAGE
●CAMERA ID ●DAY/NIGHT ●SYNC
●MOTION DET ●PRIVACY
●REVERSE
●DETAIL ●DEFAULT ●PAGE1
EXIT
7

OSD Menu Setting
LEFT
DOWN
UP
RIGHT
Push the Joy stick for one second, and the OSD appears
on the screen. Move the Joy Stick up, down, left & right to
control the OSD functions.
8

Operating your camera – SETUP
SET UP menu is displayed on the monitor screen.
1. Press the SET button (JOYSTICK) to access the SETUP mode.
2. Select the desired feature using the UP or DOWN button.
Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
Move the arrow indicator to the desired feature item.
If you press RIGHT or LEFT button, it appears available status.
Press the button when gets desired feature.
3. Change the status of the selected feature using the LEFT
or
RIGHT button.
4. When completed, move the arrow indicator to ‘EXIT" and
press
the SET button.
Notes
You can access submenu using SET button.
For the mode with ‘---’, you may not access submenu.
9

Operating your camera – SETUP LENS
1) Setting up the LENS
Select the lens pressing the RIGHT button.
① On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
②Select LENS TYPE as ‘MANUAL’using the LEFT or RIGHT button.
10

2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
① Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’using the UP or DOWN button.
②Set ‘SHUTTER’to the desired mode using the LEFT or RIGHT
button.
▶ OFF : Deactivation
▶ FLK(1/100) : Flicker mode
11

Operating your camera – SETUP SPEED CONTROL. ②
▶MANUAL : When setting the shutter speed manually.
You can select speed from ‘1/60’to ‘1/200,000’sec
12

▶ESC : You can control the BRIGHTNESS.
③When completed, press ‘SET’
Notes
Avoid pointing the camera directly at a fluorescent lamp
When the SHUTTER menu is set to FLK mode, the INTENSIFIER will not
work.
13

Operating your camera – BACKLIGHT
3) SLC (Speco Light Compensation) - BACKLIGHT
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘BACKLIGHT’using the UP or DOWN button.
②SET ‘BACKLIGHT’to the desired mode using the LEFT or RIGHT button.
A built-in SR chip provides intelligent light level control to overcom
e
severe Backlight conditions.
▶OFF ▶LOW ▶MIDDLE ▶HIGH
14

4) AUTO GAIN CONTROL (AGC)
①Press the SET button to display the SETUP menu and move the arrow
indicator to ‘AGC’using the UP or DOWN button.
②SET ‘BACKLIGHT’to the desired mode using the LEFT or RIGHT button.
AGC allows a brighter picture in low light conditions. Higher GAIN lev
el
will yield a brighter screen but you might notice an increase innoise.
▶OFF ▶LOW ▶MIDDLE ▶HIGH
15

Operating your camera – WHITE BALANCE
5) WHITE BALANCE
① Press the SET button to display the SETUP menu and move the arrow
indicator to ‘WHITE BALANCE’using the UP or DOWN button.
②Set ‘WHITE BAL.’to the desired mode using LEFT or RIGHT button.
▶ ATW (Auto Tracking White Balance)
: When color temperature is 2400~12000K, select this
mode.
(ex. A fluorescent lamp, outdoor).
This is the best setting for most conditions.
▶ AWC (Auto White Balance Control)
: The white balance is automatically adjusted in a specific environment.
In order to obtain the best result, press the set button while the camera
focuses on white paper. If the environment including the light source is
changed, you have to adjust the white balance again.
16

▶MANUAL : To fine adjust, select the Manual mode. You can increase
or decrease the red or blue factor while monitoring the difference on the
screen. Set to ‘MANUAL’mode and press the SET button. Increase or
decrease the value for RED(R-Gain) and BLUE(B-Gain), watching the
color
of the picture, and press the SET button when you obtain the best color.
Notes
Proper White Balance may not be obtained under the following
conditions
in these cases select the AWC mode.
When the scene contains mostly high color temperature object, such as
a blue sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the
place
of the changing illumination.
17

Operating your camera – REDUCE NOISE
6) REDUCE NOISE (Dynamic Noise Reduction)
DNR is to reduce the noise on the screen.
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘DNR’using the UP or DOWN button.
②SET ‘REDUCE NOISE’to the desired mode using the LEFT
or RIGHT button.
▶ OFF : Deactivatio
▶ LOW : Low reduction of the noise
▶ MIDDLE : Middle reduction of the
noise
▶ HIGH : High reduction of the noise
n
Notes
If you change the ‘GAIN’ menu from AGC-L to AGC-H
sensitivity is increased as well as noise on the screen.
When selected ‘GAIN’ menu OFF, DNR will not work.
18

Operating your camera – INTENSIFIER
7) INTENSIFIER
Allows you to get clear images with this function under night
or low light conditions
① Press the SET button to display the SETUP menu and move the
arrow indicator to ‘SENCE UP’using the UP or DOWN button.
②SET ‘INTENSIFIER’to the desired mode using the LEFT or RIGHT button.
▶ AUTO : When your camera is under night or low-lighting
level, select this mode. This mode allows the
camera to switch into B/W in low light conditions.
Notes
If you press SETUP button at ’AUTO’ menu, you can control the
lowlight action maximum magnifications.(X2~X128)
Increasing the amount of Intensification results in brighter pictures
Under low light conditions, and may increase image lag.
Increasing the amount of intensification may cause image noise
which is to be expected as a normal condition.
19