Speco O4B7MN User manual

User Manual
4MP IP Camera
O4B7MN/O4D6N/ O4D7MN/ O4T7N/ O4T7MN / O4P4N/O4B6N
Please read this manual carefully before operating the unit and keep it for further reference

Important Safeguards and Warnings
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The
product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage, and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise, it may result in CMOS sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the ca mera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an optical device, please do not touch or wipe cover surface directly during installation and use, please refer to the
following methods if dirt is found.
Stained with dirt:
Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint.
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several times if it is not clean enough.

Warning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals, and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these
without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Information
FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in a particular installatio n. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Accessory name Amount
Network Camera Unit 1
Junction box 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1

Table of Contents
1Introduction .............................................................................................................................................................................................................2
2Web Access and Login ..............................................................................................................................................................................................3
3Live View..................................................................................................................................................................................................................5
4Camera Configuration ..............................................................................................................................................................................................7
4.1 System Configuration.......................................................................................................................................... 7
4.1.1 System Information.................................................................................................................................. 7
4.1.2 Date and Time ......................................................................................................................................... 7
4.1.3 Local Recording........................................................................................................................................ 8
4.1.4 Storage................................................................................................................................................... 8
4.2 Video Configuration.......................................................................................................................................... 10
4.2.1 Image Configuration............................................................................................................................... 10
4.2.2 Video / Audio Configuration .................................................................................................................... 12
4.2.3 OSD Configuration.................................................................................................................................. 14
4.2.4 Video Ma sk ........................................................................................................................................... 14
4.2.5 ROI Configuration................................................................................................................................... 15
4.2.6 Zoom/Focus .......................................................................................................................................... 15
4.3 Alarm Setup..................................................................................................................................................... 16
4.3.1 Motion Detection................................................................................................................................... 16
4.3.2 Other Alarms......................................................................................................................................... 17
4.3.3 Alarm In (Sensor Input) ........................................................................................................................... 19
4.3.4 Alarm Out ............................................................................................................................................. 19
4.3.5 Alarm Server.......................................................................................................................................... 20
4.4 Analytics Configuration...................................................................................................................................... 20
4.4.1 Object Removal...................................................................................................................................... 20
4.4.2 Exception .............................................................................................................................................. 22
4.4.3 Line Crossing ......................................................................................................................................... 23
4.4.4 Intrusion ............................................................................................................................................... 24
4.4.5 Face Detection....................................................................................................................................... 26
4.4.6 Region Entrance..................................................................................................................................... 28
4.4.7 Region Exiting........................................................................................................................................ 29
4.4.8 Target Counting...................................................................................................................................... 29
4.4.9 Region Statistics..................................................................................................................................... 31
4.4.10 Heat Map.............................................................................................................................................. 33
4.5 Network Configuration...................................................................................................................................... 34
4.5.1 TCP/I P................................................................................................................................................... 34
4.5.2 Port...................................................................................................................................................... 35
4.5.3 Server Configuration............................................................................................................................... 36
4.5.4 Onvif .................................................................................................................................................... 36
4.5.5 DDNS.................................................................................................................................................... 37
4.5.6 SNMP ................................................................................................................................................... 37
4.5.7 802.1x................................................................................................................................................... 38
4.5.8 RTSP..................................................................................................................................................... 39
4.5.9 RTMP.................................................................................................................................................... 39
4.5.10 UPNP.................................................................................................................................................... 40
4.5.11 Email .................................................................................................................................................... 40
4.5.12 FTP....................................................................................................................................................... 40
4.5.13 HTTPS................................................................................................................................................... 41
4.5.14 QoS ...................................................................................................................................................... 42

4.6 Security Configuration....................................................................................................................................... 42
4.6.1 User Admin ........................................................................................................................................... 42
4.6.2 Online User ........................................................................................................................................... 44
4.6.3 Block and Allow Lists............................................................................................................................... 44
4.6.4 Security Management............................................................................................................................. 45
4.7 Maintenance Configuration................................................................................................................................ 46
4.7.1 Backup and Restore................................................................................................................................ 46
4.7.2 Reboot.................................................................................................................................................. 46
4.7.3 Upgrade................................................................................................................................................ 46
4.7.4 Operation Log........................................................................................................................................ 47
5Search .................................................................................................................................................................................................................... 48
5.1 Image Search ................................................................................................................................................... 48
5.2 Video Search.................................................................................................................................................... 50
5.2.1 Local Video Search ................................................................................................................................. 50
5.2.2 SD Card Video Search.............................................................................................................................. 51
Appendix ........................................................................................................................................................................................................................ 54
Appendix 1 Troubleshooting ........................................................................................................................................................................................... 54

2
1Introduction
Welcome
Thank you for purchasing this network camera!
Please read this manual carefully before operating the unit and retain it for further reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support at 1-800-645-5516.
Main Features
Built-in PoE (Power over Ethernet)
IP67 rated for outdoor installations
Remote viewing support via web browser, mobile APP, and CMS/VMS
Applications

3
2Web Access and Login
The IP camera settings can be accessed via a web browser through the LAN.
Available web browser: IE (plug-in required)/ Firefox/Edge/Safari/Google Chrome
It is recommended to use the latest version of these web browsers.
The menu display and operation of the camera may be slightly different by using the browser with plug-in or without plug-in.
Installing plug-in will display more functions of the camera.
Connect IP-Cam via LAN or WAN. Here only take IE browser for example. The details are as follows:
Access through IP Scanner
Network connection:
①Make sure the PC and IP-Cam are connected on the same local network. The camera is set to DHCP by default and will be
assigned an IP address by the DHCP server. Make sure that the local network has a DHCP server. Routers typically have a DHCP server
built in.
②Install IP Scanner from the CD and run it after installation. IP Scanner is the tool for discovering the IP cameras on the local
network.
③ In the device list, the IP address, model number, and MAC address of each device will be listed. Select the applicable device and
double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser. Read the
privacy statement and then check and click “Already Read” to enter the login interface.
The login interface is shown above. Default userna me is adm in and password is 1234. After logging in, follow directions to install
applicable plug-ins for viewing video if prompted.

4
If this is the first time for you to log in, the password prompt may only change the admin password. To change ONVIF password, you
either have to check the “Match Onvif Password” box (if available) or go to the the ONVIF section to change the password.
(ConfigNetworkPorts/ConnectionsOnvif)

5
3Live View
The window below will be shown after logging in.
The following table describes the icons on the live view interface
Icon Description Icon Description
Original size of resolution
Rule information display
Fit (correct scale) SD card recording indicator
Auto (fill the window) Abnormal color indicator
Full screen (show video only) Abnormal clarity indicator
Start/stop live view Scene change indicator
Start/stop two-way audio ( for
the model
with audio output
interface)
Line crossing indicator
Enable/disable audio Line crossing target counting indicator
Snapshot Intrusion indicator

6
Icon Description Icon Description
Start/stop local recording Sensor alarm indicator
Zoom in (for motorized models)
Motion alarm indicator
Zoom out (for motorized
models)
Face detection indicator
Zoom/Focus control (for
motorized models)
Face detection
*Plug-in free live view: Two-way audio and local recording are not supported.
All indicator icons above will flash in live view interface only when the corresponding events are enabled.
In full screen mode, to exit, double click on the mouse or press the ESC key on the keyboard.
Click the zoom/focus control button to show the control panel. The descriptions of the control panel are as follows:
Icon Description Icon Description
Zoom - Zoom +
Focus - Focus +
One key focus (used when image is out of focus after manual adjustment)
Face Capture View
① Go to ConfigEventFace Detection interface. Check “Enable”.
② Return to the live view interface. Click to go to the following interface. When there are faces detected, the face pictures
will be listed on the right.