Speco Flexible Intensifier O8FD4M User manual

1
Flexible Intensifier® Technology Bullet IP Camera
QUICK INSTALLATION GUIDE
O8FD4M
Please read this guide carefully before installation and operation of the product.

2
Notice
Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read
it carefully before operating the product and retain it for future reference. Should you require any technical
assistance, please contact Speco Technologies Technical Support.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION

3
PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and to obtain
the best picture quality.
Installation and services should only be carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and
have it checked by your authorized dealer before reusing.
Avoid installing the camera in extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance
by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera in a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Don't point the camera directly at sunlight.
Please pay special attention to keep the unit from dropping or external shock during the process of
transportation or handling.
Never try to touch the camera with wet hands. It may cause an electric shock.
Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and / or the corresponding product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassembly, repair or modification of the product by the user.
(4) Inconvenience or any loss when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, when combined with third party devices.
(6) Any claim or action for damages, brought by any person or organization, due to a violation of privacy when
the surveillance footage, for some reason, becomes public or is used for the purpose other than
surveillance.

4
1. PRODUCT OVERVIEW
Key Features
8.5 Mega pixel 1/2.5" progressive scan CMOS image sensor for excellent image quality
Vandal resistant
IP67 compliant
3-Axis mechanism
Triple stream for simultaneous operations
Supports up to 4K ultra-HD image resolution (3840 x 2160)
Integrated motion detection with pre- and post-alarm image / video buffering
Tampering-Alarm function
Controllable frame rate
Full Duplex Two-Way Audio Support
Privacy Masking
HTTPS supported (Hyper Text Transfer Protocol Secured)
Integrated E-Mail, FTP, DDNS and DHCP client
Specification
CLASSIFICATION
Dome IP Camera
General
CPU
ARM Cortex-A9 (1 GHz, Instruction cache : 32kbyte,
data cache : 128kbyte-L2, FPU )
Flash
2Gbit Flash Memory
SDRAM
8Gbit DDR3 Memory
Camera
Image Sensor
8.5 Mega 1/2.5" SONY STARVIS image sensor
Total Pixels
3864(H) x 2218(V) 8.57 Megapixel
Effective Pixels
3864(H) x 2202(V) 8.51 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0 Lux (IR LED On)
IR Distance
130 ft
Day & Night
IR cut filter
Lens
3.6 ~ 11mm Motorized Megapixel Lens
Video
Video Compression
H.265 / HEVC Main Profile Level 5.1 encoding
H.264 High profile @ Level 5.1 MJPEG
Resolutions
Up to 3840 x 2160 @ 25fps
Frame Rate
H.265 / H.264 Up to 25fps with 3840 x 2160,
H.265 / H.264 Up to 30fps with 1280 x 720
H.264 / MJPEG Up to 30fps with VGA
Video Streaming
Support multi stream with H.265, H.264, MJPEG
Adjustable frame rate
VBR / CBR
Image Setting
Brightness, Contrast, Sharpness
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
DSS, V-Flip, etc.
WDR, ATR
Video Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC / PAL
Audio
Audio Streaming
Two-way, full duplex
Audio Compression
G.711
Data / Sample Rate
64Kbps / 8KHz

5
Audio Input / Output
Microphone input / 1x Line-In, Line-Output / 1x Line-Out
Network
Security
Password protection
User access log
HTTPS encryption
Supported Protocol
HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP
System
Integration
Intelligent Video
Motion detection (4 Separate blocks)
Alarm Trigger
Motion detection, External Input (NO / NC Type)
Video Buffer
5MB pre-alarm and post-alarm-180sec
Firmware Upgrade
Remote upgrade via network
API
CGI Interface document
Physical
Power Source
DC 12V, PoE (Power over Ethernet) : 802.3af
Power Consumption
8W
Net Weight
2.6 lbs
LEDs
Power, Network Connection
Dimensions
5.1”(Φ) x 3.9”(H)
Environment
Operating
Temperature
14F ~ 122F
Storage Temperature
-4F ~ 140F
2. NAME AND FUNCTION OF EACH PART
2.1 Package Contents
APPEARANCE
DESCRIPTION
IP Camera x 1
Installation Guide x 1
Drilling Template x 1
L-Wrench x 1
Tapping Screws (Ø 4 x 30) x 3
Plastic Anchor x 3
CD x 1

6
Junction Box
Tapping Screws (Ø 4 x 30) x 4
Plastic Anchor x 4
Silicone Template x 1
Junction Box x 1
Screw PH (M4 x 12) x 3
L-Wrench x 1
2.2 Name and Function
NO.
ITEM
DESCRIPTION
Power Connector
DC12V
Network and POE
Connector
POE (Power Over Ethernet) and LAN cable
Sensor In / Alarm Out
Sensor In / Alarm out
Audio-In
Audio in (Red)
Audio-Out
Audio Out (White)
IR LED
Infrared LED
Lens
3.6 ~ 11mm Motorized Lens
luminance sensor
Control IR LED by sensing light
7
1
2
3
4
5
6
7
8
4
5
2
3
1
6
8
9

7
BNC
Analog Video Output
3. INSTALLATION
3.1 Installation overview
Ceiling
①Paste a Drilling Template on the ceiling or wall and drill screw points which will be dome for installation.
②Fix the Surface Mounting Base by using Tapping Screws provided.
③Fix the Flush mount Base on Surface Mounting Base.
④Turn the camera Ass’y to the desired direction.
⑤Turn the dome and shied cover to the camera direction.
⑥Fix the Dome Cover Ass’y to the Flush mount Base by using Torx Screw and Torx L-Wrench.
Ceiling Tile
Drilling Template
Top Cover Ass'y
Camera Ass'y
Plastic Anchor x 3
Tapping Screw (4 x 30) x 3
L-Wrench
9

8
Ceiling_Junction Box
3.2 3-Axis Adjustment
Tilt 65°
Pan 326°
Rotate 180°
Tool-free 3-Axis mounting mechanism
Perfect Tri-axis!
Panning axis up to 326°degree.
Tilting axis up to 65° degree.
Rotation axis up to 180° degree.
Ceiling Tile
Drilling Template (Silicone)
Plastic Anchor x 4
Junction box
Tapping Screw (4 x 30) x 4
Camera Ass'y
PH (M4 x 12) x 3
L-Wrench
Top cover Ass'y

9
3.3 INSTALLATION EXAMPLE
3.3.1 Installation Example
3.3.2 Connecting to the Network
Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
3.3.3 Accessing the Camera’s Web Setup Page
LAN Switch Router Internet Remote Access
LocalAccess E-Mail / FTP

10
1) Open the browser and enter the camera’s IP address in the address bar or double click the device in IP
Scanner.
2) Enter the user name and password when prompted.
3) Default user name is admin and password is 1234.
4) If prompted for installation of the Active-X plug-in, allow the installation. Active-X is needed to view video
from Internet Explorer.
Enter the IP
address here

11
4. DIMENSIONS (mm)
Ceiling
Ceiling_Junction Box