Spectra Logic Spectra 2000 User manual

P.N. 90870070 Revision B
Spectra 2000™Mammoth-2 Drive
Sled Assembly Guide

2 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide
Notices
Spectra Logic Corporation provides this publication “as is” without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties of merchantability or
fitness for a particular purpose. In no event shall Spectra Logic be liable for any loss of profits,
loss of business, loss of use or data, interruption of business, or for indirect, special, incidental,
or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of
such damages arising from any defect or error in this publication or in Virtual Control Panel
software.
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility is assumed by Spectra
Logic for its use. Due to continuing research and development, Spectra Logic may revise this publication from time to time without
notice, and reserves the right to change any product specification at any time without notice.
Some products or services mentioned in this manual are provided by companies other than Spectra Logic . Inquires about one or
more of these products or services should be sent directly to the company in question. This manual refers to the following brand
or product names, registered trademarks, and trademarks that are listed according to their respective owners. These trademarks
may be registered in this country, other countries, or both.
Spectra 2000 Mammoth-2 Drive Sled Assembly Guide
Copyright © 2001 Spectra Logic Corporation. All rights reserved.
Spectra Logic Corporation
TreeFrog™
Spectra 2000™
Exabyte
Mammoth-2™

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 3
Contents
Introduction ...........................................................................................................4
Assemble the Drive Sled........................................................................................5
Finish......................................................................................................................8

4 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide
Introduction
About this manual
This guide explains how to assemble a Mammoth-2 drive sled for use with a Spectra 2000
automated tape library.
Caution: The Mammoth-2 tape drive is a static sensitive device. Use a static
dissipative wrist strap or other ESD equipment/tools for this process.
How long will this take?
This procedure should take less than 15 minutes.
What you will need
You will need a Mammoth-2 Drive Sled Assembly Kit, P.N. 90870556. The Mammoth-2 Drive
Sled Assembly Kit contains:
You will also need:

A #1 Phillips screwdriver

A Mammoth-2 drive
Part Number Description
4250 Screws (4)
90870157 Spectra 2000 5.25” Drive Sled
90870316 SCSI ID cable
90870070 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide (this guide)

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 5
Assemble the Drive Sled
1. Assemble all parts on your work surface (Figure 1).
2. Align the Mammoth-2 drive in the drive sled so the drive door is facing the drive
sled’s front lip and the SCSI ID Settings label is visible at the top of the assembly
(Figure 2).
3. The drive sled has two screw holes at the top of each side. Position the drive so its
screw holes are aligned with the drive sled’s screw holes.
Figure 1 Drive sled assembly parts.
Figure 2 Align the Mammoth-2 in the Drive Sled.

6 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide
Assemble the Drive Sled
4. Use the #1 Phillips screwdriver to attach the Mammoth-2 tape drive to the drive sled
(Figure 3).
Note: Make sure to use only the two screw holes at the top of each side of the
drive sled. There should only be two screws on each side.
Figure 3 Attach the Mammoth-2 to the drive sled.

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 7
Assemble the Drive Sled
5. Turn the drive sled assembly over and plug the SCSI ID cable into the rear of the
Mammoth-2 drive . The keyed connector will only plug into the drive with the tab
facing up (Figure 4).
Figure 4 Plugthe SCSI ID cable into the drive.

8 Spectra 2000 Mammoth-2 Drive Sled Assembly Guide
Finish
There is a chance your Mammoth-2 drive sled may have been bent in shipping. Before installing
the Mammoth-2 drive sled in your Spectra 2000 automated tape library, check to ensure the
drive sled lip is flush with the drive face plate (Figure 5, Figure 6).
If the Mammoth-2 drive sled is bent:
1. Remove the drive from drive sled.
Caution: You must remove the Mammoth-2 drive from the drive sled before
correcting the bent drive sled lip. Failure to do so can result in damage
to the drive.
Figure 5 Drive sled lip flush with drive faceplate. Figure 6 Drive sled lip bent up from drive faceplate.

Spectra 2000 Mammoth-2 Drive Sled Assembly Guide 9
Finish
2. Using your hands, bend the drive sled so the lip is flush with the drive faceplate.
Use light pressure (Figure 7).
3. Attach the Mammoth-2 tape drive to the drive sled.
Note: If the Mammoth-2 drive screw holes will not align with the drive sled’s
screw holes, you have bent the drive sled lip too far. Remove the drive
from the drive sled and try again.
If you have difficulty
If you need further assistance with this procedure, call Spectra Logic Technical Support at (800)
227-4637 or [phone], extension 3175.
Figure 7 Bend drive sled.