Sport-thieme Kompakt 206 9539 User manual

Assembly instructions
„Kompakt“ Vandalism-Proof
Playground Goal
Art.-Nr.: 206 9539
0218214 · © 2018 Sport-Thieme GmbH
D-38367 Grasleben ·Germany
sport-thieme.com · info @sport-thieme.com
Phone: [phone] · Fax: [phone]

2
Assembly instructions for Art.-Nr. 206 9539
1. Assembly of goal
1.1 Scope of delivery:
1 x construction crossbar/uprights, welded
1 x construction ground tube/bar, welded
2 x goal net hoop (1 left/1 right)
2 x net hoop brace
2 x aluminium connecting element for goal frame to ground frame
16 x safety hexagon countersunk flat head screw DIN 7991 M8 x 20
8 x safety hexagon socket screw DIN 933 M8 x 20
2 x safety hexagon socket screw DIN 933 M8 x 16
2 x hexagon socket screw DIN 933 M8 x 60
2 x ring nut eye M8 x 80
4 x safety nut DIN 985 M8
2 x washer DIN 9021 Ø8.4
2 x aluminium nut M8 x 40
1 x hexagon screwdriver DIN 911 SW 5
80 x safety system net holder
1 x instruction of assembly
1.2 Screws and small parts: (please check for completeness before assembly)

3
Assembly instructions for Art.-Nr. 206 9539
1.3 Installation::
Step 1:
Lay ground frame (with welded xing attachments) on
the floor with upturned chamber. Push on each side 1
nut M8 x 40 into the channel of the bar. It will later be
used to x the net hoops.
Step 2:
Fix 1 connecting element each in each bar until
threaded holes are congruent with borings of bar. Then
screw both elements with 8 safety hexagon counter-
sunk flat head screws DIN 7991 M8 x 20 using the
screwdriver. Now x goal frame with the remaining 8
safety hexagon countersunk flat head screws DIN 7991
M8 x 20.
Step 3:
Stick short side of net hoops with welded flat plate
into the channel of bar/upright construction. Push
nuts which are already provided in the channel of
crossbar and upright below the borings. Now tighten
both hoops with 4 safety hexagon socket screws DIN
933 M8 x 20.
Step 4:
Stick long side of net hoops with welded flat plate
into the channel of ground frame construction. Push
nuts which are already provided in the channel of
crossbar and bar (xed in step 1) below the borings.
Now tighten both hoops with 4 safety hexagon socket
screws DIN 933 M8 x 20.

4
Assembly instructions for Art.-Nr. 206 9539
Step 5:
Place boring of the u prole welded at the net hoop
braces above the front boring in the net hoops.
Stick 1 hexagon socket screw DIN 933 M8 x 60 each on
both sides. Screw and tighten 1 safety nut DIN 985 M8
each.
Step 6:
Hold the other side of net hoop braces above the
channel of the crossbar. Push nuts which are already
provided below the boring. Screw 1 safety hexagon
socket screw DIN 933 M8 x 16 in each brace and
tighten them.
Step 7:
Insert from the inside ring nut eyes M8 x 80 through
the borings of net hoops. Then push 1 washer DIN
9021 Ø8.4 on the other side and screw 1 safety nut
DIN 985 M8 each until the thread is flush with the ele-
ment.
Maintenance, safety and storage instructions:
Finally check all screwed fastenings and to be on the safe side tighten all screws again.
To avoid damage and misuse goals have to be stored secured and in an upright position when not in use.
Only use water for cleaning the surfaces. Do not use alcohol or any aggressive chemicals!

5
Assembly instructions for Art.-Nr. 206 9539
2. Assembly of net
2.1 Scope of delivery
1x steel rope 3/4mm Ø PA coated 8 m long with one tension lock each
1x steel rope 3/4 mm Ø PA coated 6 m long with one tension lock each
1x handball goal net (Herkules Ø 5 mm)
4x screwable rope clips 3/16 galvanized
8x nuts M5 galvanized
100x black lacing cords 8 x 240
1x net steel rope with tension lock
5x large green net eyes
4. Pull the open end of the 8 m long steel rope through the green eyes of uprights/
crossbar. Start in the above mounted rst big green eye of the net at the bottom of the
upright, continue to the top, along the outside of the net hoop, the crossbar, again
along the outside of the other net hoop and then down to the eye of the other upright.
Pull the rope until you can easily clip the tension lock in the eye at the starting side.
5. Mount orange net holders (optionally 80 pieces) so that they are always on the same
level between the net meshes (in turn with green net eyes). The tension ropes of the net
have to run in the round eye of the net hoops. For this reason bend open the net hol-
ders a little. After having adjusted the net holders in the channel they will be xed by a
90° rotation. The net holders have to be mounted as follows:
2.2 Fixing of net at goal frame:
1. Lay out net over the goal frame and adjust it.
2. Clip the premounted net rope into the ring nut eyes of goal hoops.
3. Take at one side of the net (at welded eyes of uprights and bar)
the rst 2 small green eyes and replace them with the attached
big green eyes. Thus in total 4 eyes have to be replaced as the
tension lock cannot be xed in the small eyes.
6. Repeat steps 4. and 5. at the ground frame with the rope, length 6 m. Start also at the bar’s side with already mounted big
green eyes.
7. Check and adjust net again as now the nal xing at the net hoop will be done.
8. Pull steel ropes tightly and x them with screwable clips and nuts. Tense ropes and cut rope ends.
9. Fix back tension rope between net hoops in each mesh of the net with the attached lacing cords (tighten lacing cords). Pull
the tension rope (not so tight, slightly sagging). Cut lacing cords accordingly. Also x each mesh of the net at the goal hoops
using the lacing cords.
10. In order to avoid rubbing of the net at frame or tension elements during the matches the net has to be tightly mounted and
xed by the lacing cords.
Safety instruction:
Finally check all screwed fastenings and to be on the safe side tighten all screws again.