Park & Sun Sports GT-BS-SOC1100 User manual

©2009 All Rights Reserved Park & Sun Inc,
BLUE SKY SOCCER TABLE ASSEMBLY INSTRUCTIONS
(GT-BS-SOC1100)
[email protected]
2150 S Tejon St • Englewood, CO 80110
Toll free: 800-776-7275 • Local: 303-935-8449

©2009 All Rights Reserved Park & Sun Inc,
Congratulations on your new outdoor Blue Sky Soccer table purchase. This product has been designed for outdoor and indoor use
utilizing lightweight, high-impact materials, components and hardware.
Note: Although all materials are designed to meet the outdoor elements, there may be some slight component and hardware
discoloration that occurs. This will not affect the function of the table.
Before you begin:
• Inventory all parts prior to table assembly.
• Recommend two adults for assembly process.
• Do not over tighten or cross thread hardware provided.
 • Priortotighteninghardware,makesureallconnectionsareushatbothconnectingpoints.
Parts List
Warning: Contains small parts – Choking hazard
Player Rod Hardware
 8-5/8”Carbonberplayerrods(black)
8 - Rod grips
8 - Rod grip bolt and nut set
26 - Player/Stopper bolt and net set
8 - Rod caps
16 - Rod washers
16 - Rod rubber bumpers
4 - Goalie position stops
11 - Blue players
11 - Red players
Game Table Frame/Surface Hardware
2 - Side panels with surface supports
2 - End panels with goal and surface support,
abacus score bars, ball return.
2 - Aluminum legs with adjustable footers
2 - Aluminum legs with casters
1 - Aluminum center surface support
4 - Corner cap protectors
2 - Ball returns catchers
2 - Ball return hoses
4 - Ball action surface panels
2 - Soccer balls
16 - 1” Threaded allen head panel leg bolts
16 - ¾” Surface and ball catcher screws
 1-Blueutedplayingsurface
1 - 4mm Allen wrench

©2009 All Rights Reserved Park & Sun Inc,
Assemble in open area on soft surface
Step 1: Parts required: 1 leg with caster, 1 leg with footer, 1
side panel, 2 corner cap protectors, and 4 panel bolts. Place
the side panel facedown and line up the legs on opposite ends
of the side panel. Starting on one side, line up the inside of
the leg with the outside of the panel in line with the mounting
holes. Start the bolts and before tightening, place the corner
capontopofthesidepanelandushtotheinsideoftheleg.
Tighten the bolts with the Allen wrench provided. Repeat the
following on the opposite side. Once complete, repeat step 1
for the remaining side panel and legs.
Step 2: Parts required: assembled side panels, end panels
and panel bolts. Lay down side panel on it’s outside, and line
up end panel inside of leg, aligning the mounting holes, start
the panel bolts by hand and tighten once top and bottom
bolts are started. Repeat the opposite side.
Step 3: Brace the remaining side panel against a wall if
possible or have another adult hold the panel up. Line up the
side panel with the end panels and to the other side panel.
Align with the mounting holes. Begin to insert the panel bolts
on the top and bottom by hand. Repeat this step on the
opposite side of the panels. Tighten the bolts with the Allen
wrench.
Step 4: Attach the ball catcher using ¾” screws with the ball
receiving hole at the bottom of assembly.
Step 5: Attach the return hose to the goal and ball return.
Corner cap
protector

©2009 All Rights Reserved Park & Sun Inc,
Step 6: Set the blue playing surface onto the side panel and goal box
supports. Attach using 8 - ¾” screws into the surface pre-drilled holes.
Note: The surface supports do not have pre-drilled holes.
Step 7: Position the white ball action surface panels before adhering them
to the playing surface. The top and bottom overlap. Remove the double back
tape and adhere each panel into position. Do not apply too much pressure
while securing the surface panels.
Step 8: Attach the aluminum surface support angle. Remove the backing
from the double back table and adhere the support angle underneath the
surface at center, side to side.
Player and Rod Assembly
Review player position and placement diagram
Each rod will have 2 washers, 2
rubber bushings.
Select players, rod stops, handle
grips and caps. Use appropriate
hardware and tighten using a
philips head screw driver.
You are now ready to play!
Storage and maintenance tips:
-Keeping the table covered when
not in use will prolong the life of
your table.
-Keep clean and free from dirt or
dust(Anynon-chemicalcleaner
works.)
-Lubricate bearings as needed.