Sport-thieme 201 0915 User manual

Sport-Thieme®
Handball Goal, 3x2 m,
Free-Standing or socketed
Art.-Nr.: 201 0915
203 4502
Assembly instructions
0218214 · © 2018 Sport-Thieme GmbH
D-38367 Grasleben ·Germany
sport-thieme.com · info @sport-thieme.com
Phone: [phone] · Fax: [phone]

2
Assembly instructions for Art.-Nr. 201 0915/203 4502
1. Scope of delivery
Please check the following content before assembly.
The following indicated quantities refer to 1 Handball goal. In case of a delivery in pairs we double the
amount correspondingly. Pictured colours of proles are only samples and may dier from delivered proles.
1x Galvanized steel ground tube Ø ¾“
1x Crossbar, prole 80 x 80mm
2x Uprights, prole 80 x 80mm
1x Hexagon screwdriver SW6, DIN 911, length approx.
470mm (only for goal in ground sockets)
2x Rigid net hoop 2x Steel corner joint
8x Steel plate
2x Upright cap
Accessories
Only for catalogue no. 2034502 –
goal in ground sockets:
2x Ground socket, length 300 mm
2x Cap for ground socket
Accessories:
32x Net holder
2x Bushes with thread M8, of aluminium round tube 20 x 5
mm, length 40 mm
6x Plastic holder
8x Safety hexagon screw M8 x 50mm, DIN 931
8x Safety hexagon socket cylinder screw M8 x 14mm, DIN 912
2x Hexagon screw M8 x 90, DIN 931
2x Hexagon screw M8 x 12, DIN 933
10x Self-locking nut M8, DIN 985
4x Self-locking cap nut M8, DIN 986
4x Ring nut M8 x 50
8x Plug pin
1x Hexagon screwdriver SW5, DIN 911, black
1x Hexagon screwdriver SW6, DIN 911, length 120 mm
1x Assembly instruction

3
Assembly instructions for Art.-Nr. 201 0915/203 4502
2. Assembly of the goal
The following tools are necessary:
- 2 wrench/ring spanners 13 mm
- 1 mallet/hammer
- 1 drill Ø 1.5 mm
- 1 thin screw driver (for net hook xing, if necessary)
a) Assembly of crossbar/uprights:
Lay crossbar and uprights on the ground, groove facing upwards and mitres joining. Stick 4 steel plates on steel corner joint (see
1st picture bottom left). Then stick crossbar and upright on steel corner joint (see other bottom pictures).
b) Assembly of net hoops:
Place rigid net hoops on the right and left side of crossbar/upright construction. Fixing of net hoop at the top: Screw 4 hexagon
socket screws M8 x 50, DIN 931 into the steel corner joint (see picture bottom left).

4
Assembly instructions for Art.-Nr. 201 0915/203 4502
c) Assembly of net hoop at the bottom- goal free standing, cat. No. 2010915:
Screw from upright’s inside 4 hexagon socket cylinder screws M8 x 14mm, DIN 912 in the bottom end of the upright with
extended hexagon screwdriver SW6, length 120 mm. Fix from the outside 4 nuts M8, DIN 934 (see 1nd to 3th bottom pictures).
Then adjust net hoops at the top and at the bottom and tighten all screws.
Assembly of net hoops at the bottom - goal in ground sockets, cat. no. 2034502:
The assembly is done as described above but with extended hexagon screwdriver SW6, length approx. 470 mm (see the following
pictures).

5
Assembly instructions for Art.-Nr. 201 0915/203 4502
d) Assembly of caps:
Stick caps in the open ends of uprights (see picture bottom left). Bore them with drill 1.5 mm through the holes provided in the
uprights. Then x plug pins with a hammer/mallet (see picture bottom right).
e) Assembly of ring nut:
Stick from the inside ring nuts M8 x 50 through lateral and upper net hoop holes and x them with cap nuts M8, DIN 986 (see
bottom picture).
f) Assembly of ground tube:
Stick hexagon screw DIN 931, M8 x 90 through bush of aluminium tube (see picture bottom left). Then push bush into the ground
tube (see picture bottom mid) and screw hexagon screw DIN 933, M8 x 12 through holes of bush and ground tube. Tighten screw
(see picture bottom right).

6
Assembly instructions for Art.-Nr. 201 0915/203 4502
Fix ground tube between the net hoops (see 1nd picture bottom left). Screw 1 self-locking nut M8, DIN 985 so that the nut outside
is flush with the screw of the bush (see picture bottom right).
Then unscrew hexagon screw at the ground tube. Finally push screw with self-locking nut completely into the ground tube so that
the nut is directly xed on the net hoop (see pictures bottom left and right). Then tighten all screws and nuts.

7
Assembly instructions for Art.-Nr. 201 0915/203 4502
3. Assembly of the net
a) The net is not part of the delivery.
Fix net holders at the net rope. Bend open net holders a little and press rope into the holders. We recommend the following
distribution of net holders:
crossbar : 16 pieces
uprights : 8 pieces each
After having mounted all net holders x net at the goal construction. Erect the goal. Stick net holders in the net hook rail and x
them with a 90 degrees’ rotation. Use a thin screw driver if necessary (please avoid damages at the goal).
Fix net with plastic holders in the bottom part of net hoops. Cut o protruding ends of plastic holders (see picture bottom right).
b) Fix ends of upper and lower tensioning rope at the mounted ring nuts. Cut o protruding rope ends (see bottom picture).
c) Dismantling of the net is also done by rotation of the net holders through 90 degrees. Use again a thin screw driver if necessary.

8
Assembly instructions for Art.-Nr. 201 0915/203 4502
4. Assembly of the ground sockets
a) For handball gates with a size of 3,00 x 2,00 m the distance of the ground sockets must be 3,08 m (middle socket – middle
socket = center distance).
b) Concrete ground sockets according to the sketch. Foundation dimensions: 800 x 800 x 800 mm.
c) Do not apply an acceleration mixture or antifreeze during as these adhesives may cause damages to the ground sockets.
d) After hardening of the concrete, the goal can be inserted into the sockets.
5. Maintenance, safety and storage instructions
This goal is only constructed for Handball and not for other purposes. Check all screwed fas-
tenings before use and repeat it from time to time. It has to be protected against overturning at
any time.
Do not climb net or goal frame. It is not allowed to x additional parts or extensions at the goal
frame which may impair the safety of the goal (according to EN 749).
Check screwed fastenings regularly and change damaged and wearing parts if need be. The unit should be maintained once a
year by skilled personnel.
Notice: Due to our continuous quality check of products and
equipment technical modications are possible.
To avoid damage and misuse goals have to be stored secured and in an upright position when not in use.