Sportop U80 Operation manual

U80
MODEL :
Owner’s Operating Manual ENGLISH

Main frameA
AdaptorI
Central supporting
tube
BRear stabilizerC
DFront stabilizer
Handle barE
ConsoleG
HSaddle
Saddle tube &
Saddle basement
F
KLeft pedal (K1) &
Right pedal (K2)
Tool
Water bottleL
4m/m
6m/m
KnobA46

J7
Step 1. Remove the preassembled nut (J1), spring washers (J2), and washers (J3) from
the rear stabilizer (C).
Step 2. Attach the rear stabilizer (C) to the main frame (A) with nut (J1), spring washers (J2),
and washers (J3).
FIGURE 1 : Rear Stabilizer Assembly
Step 1. Remove the preassembled screws (J6), spring washers (J2) and washers (J3) from
the front stabilizer (D).
Step 2. Attach the front stabilizer (D) to the main frame (A) with screws (J6), spring washers (J2)
and washers (J3).
FIGURE 2 : Front Stabilizer Assembly
J3
J2
J1
C
A
A
J3
J2
J6
D
Use tool :
Use tool : 6m/m

Note: Additional assistance may be needed to help connect sensor wire
and to stabilize central supporting tube (B).
Step 2. Locate and connect sensor wire (M1) with sensor wire (M2),
.ylreporpdeniojerasnoitcennocerusekam
Note: Be careful not to pinch wires while joining the central
supporting tube (B) to the main frame (A).
Step 3. Place the central supporting tube (B) into the main frame (A)
, spring washers (J12) and )4J(swercshtiwmehtniojdna
Step 4. Use a 6m/m Allen wrench to tighten screws (J4) firm.
FIGURE 3 : Central Supporting Tube Assembly
Step 1. Remove nuts (J8) and washers (J9) from the
central supporting tube (B).
Step 2. Join the handle bar (E) assembly to the central supporting
tube (B) using the same washer (J9) and nut (J8).
Step 3. Using a 13mm wrench to tighten nut (J8) firm.
FIGURE 4 : Handle Bar Assembly
A
J4
J5
M1
J5
J4
Note!
Note : Do not pinch the sensor wire when assembling
E
J8
J9
J8
J9
J12
J12
Use tool : 6m/m
Use tool :
Step 1. First, remove the screws(J4), spring washers (J12) and
washers(J5) from the main frame (A).
washers(J5).
B
A
M2
J4
J5
J12
B

Step 1. Remove four screws (G1) on the back of the console (G).
Step 2. Connect cable (M2, M4, M5) and the handle pulse sensor wires (M3)
to the console (G). The handle pulse sensor wires (M3) can be interchangeable.
Step 3. Mount the console (G) onto the central supporting tube (B). Be aware of
the wire location at all times to prevent any pinched wires.
Push any extra wires back into the mounting hole of the handle
bar (E). Side the console down until it cannot be pushed any further.
Step 4. Using a screw driver, tighten the console (G) using the same
screws (G1).
FIGURE 5 : Console Assembly
FIGURE 6 : Install Bottle Holder
G1
B
E
G
Put water bottle (L) on bottle holder cover.
M2
M3
M4
M5
L
Use tool :

FIGURE 8 : Saddle & Seat Tube Assembly
Adjust the saddle position and height of the bike by loosening
knobs (A46) and (F4).
Adjust both adjustments according to
placement and then firmly tighten each
each rider’s desired
saddle from moving.
knob to prevent the
How to Adjust Saddle Position
A46
H
F
H1
H2
F4
F2
Step 1. Remove nuts (H1) and washes (H2) on the back of the saddle (H).
Step 2. Position seat (H) onto the seat basement (F2) and tighten it using nuts (H1) and
washes (H2).
Step 3. Loosen the knob (F4) on the seat tube receiver and pull on the knob (A46) to allow the seat
Once the seat tube (F) is positioned in the desired location, release the knob (A46) and
.erucesotbonkehtnethgit
Step 4. Remove screw (J11) on the seat tube (F).
Step 5. Loosen the knob (F4) and gently slide the seat basement (F2) onto the seat tube (F).
Let the inside styrofoam slide out at the same time. Then screw back the same screw (J11)
onto the seat tube (F).
Note: Do not take out the inside styrofoam
until “FIGURE 8 - Step 5.” to let the
stopper (F5) inside the seat
noitisopthgirehttates tnemesab
.reviecernwodedilsot)F(ebut
J11
Use tool :
4m/m
F5

Note: Locate the left & right pedals. There is a Left and Right mark on each pedal and each pedal strap
to distinguishing them.
Step 1. Tighten the left pedal (K1) counter-clockwise to left crank arm and the right pedal (K2)
clockwise to right crank arm. Use a 15mm wrench to tighten each pedal as tight as possible.
Step 2. Insert the pedal straps into each pedal. Adjust the straps according to the user’s shoe size while
on the bike.
FIGURE 9 : Pedal Assembly
FIGURE 10 : How to Transport the Bike
K1
If the machine needs to be transported to a different location, lift up the rear stabilizer until the front
transport wheels are touching the ground. You may now move to the desired location. After the move,
gently set the machine down at its new location and adjust the stabilizers’ end caps to stabilize the
machine if needed.
WARNING: Never attempt to lift the bike by yourself, ask for additional help if needed and never attempt
to lift the machine if you have any medical issues.
K2
NOTE:
if the machine dose not sit level, you
can use the two adjustable end
caps(C2&C3) to compensate for uneven
floors.
C2
C3
Use tool :

Maintenance instrucons
Read all maintenance instrucons fully before you start any repair work. In some condions, an
assistant is required to do the necessary tasks.
Equipment must be regularly examined for damage and repairs. The owner is responsible to make
sure that regular maintenance is done. Worn or damaged components must be repaired or replaced
immediately.
Only manufacturer supplied components can be used to maintain and repair the equipment.
Disconnect all power to the machine before you service it.
Daily: Before each use, examine the exercise machine for loose, broken, damaged, or worn parts. Do
not use if found in this condion. Repair or replace all parts at the first sign of wear or damage.
Make sure adjustment knobs are ght. Tighten as necessary. Aer each workout, use a damp cloth to
wipe your machine and Console free of moisture.
NOTICE: If necessary, only use a mild dish soap with a so cloth to clean the Console. Do not clean
with a petroleum based solvent, automove cleaner, or any product that contains ammonia. Do not
clean the Console in direct sunlight or at high temperatures. Be sure to keep the Console free of
moisture.
Before each use
 Ensure seat is adjusted to the correct height and that the locking knob is secure.
 Ensure foot straps are set to the correct posion for your show before starng exercise.
Weekly: Check pedals and fixed seat bolts and ghten as necessary.
 Clean the machine to remove any dust, dirt, or grime from the surfaces.
 Check for smooth seat operaon. If needed, sparingly apply a thin coang of silicone lube to
ease operaon.
 Silicone lubricant is not intended for human consumpon. Keep out of reach of children.
Store in a safe place.
Note: Do not use petroleum based products.
MAINTENANCE
 Maintenance Parts
 Adjustment Handle, Seat Slider (F) Adjustment Handle (A46) , Handlebar Post(F)
 Seat (Part H) Seat Post ( Part 10)
 Pedal w/Foot Restraint (Part K1 & K2 le, right )
TROUBLESHOOTING
Condion/Problem Things to Check Soluon
 No display/paral display/ unit will not turn on
 Check Power pack adaptor (I) , replace if required, ensure connecon to cycle is good.

 Connecon should be secure and undamaged. Replace adapter or connecon at unit if either
are damaged.
 Check data cable integrity All wires in cable should be intact. If any are visibly crimped or cut,
replace cable.
 Check console display for damage
 Check for visual sign that console display is cracked or otherwise damaged. Replace Console
if damaged.
 Console Display If Console only has paral display and all connecons are fine, replace the
Console.
 If the above steps do not resolve the problem, contact Customer Service or your local
distributor
Unit rocks/does not sit level
 Check level adjustment Levellers may be turned to level machine.
 Check surface under unit Adjustment may not be able to compensate for extremely uneven
surfaces. Move machine to level area.
Pedals loose/unit difficult to pedal/ Pedals seem to skip or slip with a sudden increase in rpm
 Check pedal to crank connecon
 Pedal should be ghtened securely to crank arm. Be sure connecon is not cross-threaded.
 Check crank arm to axle connecon
 Crank arm should be ghtened securely to axle.
Clicking sound when pedalling
 Check pedal to crank connecon
 Remove pedals. Make sure there is no debris on threads, and reinstall the pedals.
Seat post movement
 Check locking pin (A46) Be sure adjustment pin is locked into one of the seat post
adjustment holes.
 Check locking knob Be sure knob is securely ghtened.

screen brightness metric switching
exit
WIFI select
WIFI ON / OFF
volume
image 4
updates
LANGUAGE

image image