SportsArt Fitness A983 User manual

A983
OWNER'S MANUAL
ASSEMBLY INSTRUCTIONS
S MMITH ACHINE

A. Safety Instructions:
˙Read all cautions/warnings and obtain proper instruction on use of the machines
prior to using. Use appropriate positioning and controlled movements.
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
Assemble and operate the machine on a solid, level surface. DO NOT use
outdoors or near water.
Never allow children on or near the machine.
Make sure all fasteners are properly tightened for safety. DO NOT use the
machine if the unit is disassembled in any way.
Keep head, limbs, and fingers clear of all moving parts.
If at any time during exercise you feel faint, dizzy or experience pain, stop and
consult you physician.
DO NOT wear loose or dangling clothing while using the equipment. Keep away
from all moving parts.
Use care when mounting and dismounting the unit.
DO NOT use any accessories that aren't specifically recommended by the
manufacturer. These might cause injuries or cause the unit to fall.
Close supervision is necessary when this machine is used by, on, or near
adolescent, invalids, and disabled persons.
Use this machine only for its intended use as described in this manual.
Never operate this machine if it has been damaged in any way. If it is not working
properly, been dropped or damaged, contact your dealer. DO NOT attempt to fix a
broken or jammed machine. Notify floor staff.
Never drop or insert any object into any opening.
1

2
B. Introduction
Pulley
Main frame
Pulley holder
Sliding rod
Hook
Bullet end cap B
Set springs
Elevation connector
Linear bearing sleeve
Foot pad
Rear frame
Connector A
Covers
Hook plate
Lifting rod
Guide bushing
Weight plate rod
Bullet end cap A
Connector B
Stack Track
Weight stack
Safety pad

C. List of Parts
1.Two main frames
2.One connector A
3.One connector B
4.Two pulley holders
5.Eight weight plate rods
6.One lifting rod
7.Two bullet end caps B
8.Two set springs
9.One L shaped hex key wrench M4
10.One L shaped hex key wrench M5
11.One L shaped hex key wrench M6
12.One L shaped hex key wrench M10
13.One double-end open wrench 8mm*17mm
14.One double-end open wrench 12mm*15mm
3

1. Pulley holder-Right
2. Elevation connector set-Right
3. Assembly parts package *2
4. Main frame *2
5. Lifting rod
6. Connector A
7. Rear Frame-Right
8. Pulley holder-Left
9. Connector B
10. Rear Frame-Left
11. Weight plate rod *8
12. Elevation connector set-Left
13. Weight stack *2
14. Cover *4
4

D. Assembly Instruction
Installation of Rear Frame
Step 1: Secure left rear frame onto the left frame as shown.
Step 2: Repeat step 1 for right frame assembly.
Nuts
Flat washer
Spring washer
Screws
5

6
Installation of Connector A & B
Step 1: Secure left and right rear frames with connector B as shown below.
Nuts
Flat washer
Spring washer
Screws
Nuts
Washer
Fixing plate
Spring washer
Screws
Screws
Spring washer
Flat washer
Nuts
Screws
Spring washer
Fixing plate
Washer
Nuts
Step 2: Secure left and right main frames with connector A as shown below.

7
Weight plate rod installation (8 rods as shown)
Step 1: Insert the weight plate rod into the rear frame as shown.
Step 2: Secure with screws provided.
Step 3: Repeat step1-2 for installation of the other 7 weight plate rods.

8
Installation of lifting rod
Step 1: Put the lifting rod horizontally through the gap between the sliding rod and hook
plate on both sides.
Step 2: Hang the lifting rod onto the hook plate. The recommended height is from the
4 to the 6 shelf.
Step 3: Secure left and right elevation connectors onto the handlebars.
Caution: parts are specific to right and left sides. Please identify parts as being for left
or right side before installation.
th th

9
Step 4: Pull the linear bearing sleeves up and secure the parts with the elevation
connectors on both sides as shown below.
Flat washer
Spring washer
Screws
Flat washer
Spring washer
Screws
Flat washer
Spring washer
Screws
Flat washer
Screws
Spring washer

Step 5: Follow the instructions below to assemble the parts provided:
1.Assemble the plastic part provided onto the lifting rod handlebars.
2.Secure washers and screws.
3.Secure bullet end caps.
4.Secure the set springs.
10

Installation of cables and weight stacks
Step 1: Loosen screws before removing covers.
Step 2: Identify pulley assemblies as to left and right.
Step 3: Secure pulley assemblies with the frame on both sides.
11

Step 4: Release the right side weight stack bands.
Step 5: Pull the right side weight stack up just above M (the hole on the stack track),
then use the tools provided to go through M to hold the stack.
(Caution: Be careful not to pinch your fingers and hands.)
Step 6: Hang the lifting rod on the highest shelf.
12

Step 7: Put the cable right through E, F, and G as shown.
Step 8: Secure the cable with nuts after the cable goes through H as shown.
13

Step 9: Remove the tools.
Step 10: Repeat steps 4-9 to install the left side.
Step 11: Secure covers onto the frame.
Step 12: Test if the lifting rod can go up and down smoothly.
Note: The length between the left and right side frame should range from
1490-1497 cm as shown.
14

Test tip for left and right side frame assembly:
Step 1. After completing the assembly, please hang the lifting rod on the top shelf.
Does the hook fit in the hook plate? Then hang the lifting rod on the
bottom shelf. Does the hook fit in place?
Step 2. If not, please the foot tube to let the hook fit on the hook plate
as shown.
perfectly
perfectly
adjust perfectly
15
after adjustment
Before adjustment
Foot tube
hook plate
hook

Cautions:
The guiding sets "A" & "B" should stick to the hook plate while in operation. Improper
placement would not only damage the machine, but also lose its intended efficacy of
protection.
16

E.MAINTENANCE SCHEDULE
(A983) Maintenance Schedule
1
2
3
4
Clean.
Inspect for looseness.
Tighten if needed.
Wipe clean with a damp cloth.
Exterior
Screws
Guide rod
Cable Inspect for wear and
breakage.
17

Like cars, fitness products require maintenance. Regular maintenance extends
product life, and failure to maintain products can void the manufacturer's warranty.
Copy the maintenance log sheet, and record maintenance work for each fitness
product.
1. Use a clean, lint-free towel, dampened with a mixture of Simple Green all-purpose
cleaner and water, to thoroughly clean the product exterior.
2. Inspect parts for looseness, and secure all loose screws. Make sure that the
product is safe for operation. If safety issues arise, place an "Out of Order" sign on
the product, and call for service.
3.
Please follow standard safety precautions when working on this product.
Do NOT use cleaners with alcohol, ammonia, or other damaging chemicals. The use
of such chemicals can damage the product and void the warranty. Never spray or
pour any liquid directly onto the product. Doing so can damage electronic
components and void the warranty.
This product has moving parts that can be hazardous. Exercise caution when
maintaining, operating, or moving this product.
Daily tasks
Caution
Clean guide rods. Use a clean, lint-free towel, dampened with a mixture of Simple
Green all-purpose cleaner and water. Apply a small amount of silicone lubricant
onto the guide rods.
1.Inspect belts or cables (as applicable) for wear and breakage. Replace belts once
every four years.
Weekly tasks
‧
‧
R
R
F.MAINTENANCE TASK LIST (STRENGTH PRODUCTS):
18

G.MAINTENANCE ONE-YEAR MAINTENANCE LOG:
Daily Tasks
Notes:
Facility : Supervisor:
Product Model Number : Serial Number:
Start Date: End Date:
Weeks 1-7 Weeks 8-14 Weeks 15-21 Weeks 22-28
Completed
Daily Tasks Weeks 29-35 Weeks 36-42 Weeks 43-49 Weeks 50-52
Weeks 1-7 Weeks 8-14 Weeks 15-21 Weeks 22-28
Completed
Weekly Tasks
1 2 3 4 5 6 7 8 9
Completed
Monthly Tasks
Completed
Weeks 29-35 Weeks 36-42 Weeks 43-49 Weeks 50-52
Completed
Weekly Tasks
10 11 12
Quarter 1 Quarter 2 Quarter 3 Quarter 4
Completed
Year 1
Completed
Yearly Tasks
Quarterly Tasks
19