
P.11
•NOT suitable for children under 36 months. Small parts
•Can't the sun insolates, avoid children such as dizziness.
choking hazard.
• Adult supervision is required at all times. Never leave children
unattended.
• Product MUST be assembled and checked by an adult.
• This product is only intended for outdoor and domestic use.
• Only one child per ride seat at any one time.
• Age recommendation for this product is 3-8 years.
• Max. user weight for see saw seat is 30 kg.
•DONOT stand on see saw seat.
surface at least 2 metres ( 7.5 feet)from any structures or
obstructions such as fences, walls , garden borders,washing
lines, electrical cables.
•Ensure the product is installed over a soft surface, such as
grass or sand, or wood bark which should have a depth of
minimum 15 cm ( 6 inches).Installation area should be regularly
checked and any shock absorbing materials replenished to
maintain a correct depth regarded suitable for the product
otherwise injuries may occur from a fall.
•DONOT install the unit over concrete, asphalt, gravel or any
hard surface which may cause injury should a fall occur.
•DONOT allow children to use the product until it has been
properly assembled and checked by an adult.
•Ensure children wear suitable clothing whilst using the
product. Do not allow loose clothing, clothing with draw -
strings, jewellery or any article of clothing that might be
potentially hazardous whilst using the product.
•DONOT let children use this equipment in any manner other
than the correct intended use.
•DONOT allow children to dis-mount the see saw whilst
still moving.
•DONOT allow children to wander into the play area when the
product isin use.
•DONOT allow children to climb or play on the product whilst
the product is wet as slips or falls may occur
•DONOT allow children to swing empty rides as they may
strike and injure other children.
designed for use with the product; such as, but not limited to,
cables, skipping ropes, nursery swing seats as they may cause
injury.
• Remove and dispose of all packaging materials before the
product is used.
• Once assembly is complete carefully check the equipment
before use to ensure all parts are correctly assembled. Check all
•Check all parts of the product at regular intervals, cross beam,
carried out the product could over-turn or otherwise become a
hazard.
•Check metal sections and components for signs of
corrosion.
•Discontinue use if any weakening or breakage is
found.
• The product has maintenance instructions
highlighting the need to carryout checks and
maintenance of the main parts at regular intervals.
Whenever practical ,the maintenance instructions shall
also be axed to the toy.
• Please retain these instructions for future reference.
• Teach children to use the product correctly and sit in
the centre of ride seats whilst in use.
TIGHTENING NUTS & BOLTS
• At the start of assembling DONOT FULLY tighten bolts
/ nuts all the way so as to allow some possible
adjustment for ease of assembly.
•DONOT use pliers to tighten up screws as they can
cause damage to paintwork and nuts and bolts.
• After all major components are assembled goback
over all bolts and nuts and properly tighten all before
using the product.
•Carry out checks and maintenance of the main frame
parts- cross beam, legs, ropes, anchors, nuts, bolts and
rides before each play session and at least every two
weeks.
•Check all nuts, bolts and fittings for tightness and
tighten if required.
•Check unit for sharp edges which may have occurred
during shipping, assembly ,abuse or everyday usage
.Replace if required.
•Check see saw for any evidence of deterioration,
cracks or exposed edges which could cause injury.
•Oil all metallic moving parts.
• To help maintain the products appearance,
occasionally clean the seats and metal framework with
a damp cloth lightly – but do not use abrasive chemical
cleaners.
• When you wish to disassemble or dispose of the
product please completely disassemble the unit and
discard of it in a safe place and manner so as not to
present any hazard to any individual.