Spotsee Log-IC User manual

Log-IC User Manual

1
This document is wrien and published by SpotSee All rights reserved.
USER MANUAL
Log-IC Recorder Basics ........................................................................................................... 2
Turning a Recorder On/O................................................................................................................................................ 3
Checking the Status of a Tag ............................................................................................................................................. 4
Log-IC USB ......................................................................................................................................................................... 5
Proper Placement of LOG-IC............................................................................................................................................. 5
Optional Log-IC Desktop Readers......................................................................................... 6
Contents

2
This document is wrien and published by SpotSee All rights reserved.
USER MANUAL
LOG-IC RECORDER BASICS
Status Buon
HI Excursion Display Window
Acve Display Window
LO Excursion Display Window
ON/OFF Buon
In the following secons, the following symbols represent a solid LED light:
SOLID RED SOLID GREEN
The following symbols represent a blinking LED light:
BLINKING RED BLINKING GREEN

3
This document is wrien and published by SpotSee All rights reserved.
USER MANUAL
TURNING A RECORDER ON/OFF
There are several options for turning on/off Log-IC. The instructions below describe using the ON/ / OFF Button. In order
to use the ON/OFF button on the front of the tag, the tag must be placed in standby mode and configured using the Log-IC
Interface Application.
TURNING A TAG ON
TURNING A TAG OFF
Press the ON / OFF button between your forefinger and thumb. While pressing
the button, view the Active display window. There will be a momentary solid
green light displayed in the status window, indicating you have successfully
turned the Log-IC tag on.
Once Log-IC is successfully turned on, the programmed startup delay (soaking)
time will begin.
After the delay period has expired, the tag will begin recording time and
temperature.
NOTE: If the ON button is pressed during the delay period, the delay period will start again. This
feature prevents the tag from being turned off immediately after it was turned on.
To stop manually, press and hold the ON / OFF button between your forefinger
and thumb for one full second. While pressing the ON / OFF button, view
the Active LED display window. A green light will flash two times in the Active
display window, indicating that the tag has been successfully turned off.

4
This document is wrien and published by SpotSee All rights reserved.
USER MANUAL
CHECKING THE STATUS OF A TAG
Press the Status button between your forefinger and thumb to check the current excursion status and tag mode.
You will see one of the following combinations from the LED display windows:
The tag is recording; no excursions
have occurred.
The tag is recording and there has
been a low (LO) excursion.
The tag is recording and there has
been a high (HI) excursion.
The tag is recording and there has
been a high and low excursion.
The tag is off, delayed/soaking or
in standby.
SOLID SOLID
SOLID
SOLID
SOLID
SOLID
SOLID
SOLID BLINKING

5
This document is wrien and published by SpotSee All rights reserved.
USER MANUAL
LOG-IC USB
Log-IC tags communicate to the Log-IC Interface Application via USB port. To access the USB, remove the cover as shown
and plug into an available PC USB port.
When connected, the tag LEDs will blink, confirming a successful connection.
After the tag information is downloaded, replace the cover of the USB port for next use.
PROPER PLACEMENT OF LOG-IC
Log-IC are compact and durable. They can be used whenever a complete temperature history or temperature breach alert
is necessary. As a general rule, the best placement of a monitoring device is as close to the product being monitored as
possible.
Place the Log-IC tag inside the plastic
shipping pouch, and place the plastic
shipping pouch inside the shipping box.

Rev: 12/2019
USER MANUAL
This document is wrien and published by SpotSee All rights reserved.
OPTIONAL LOG-IC DESKTOP READERS
The desktop reader (DTR) offers the advantage of easy, fast downloading of recorded data. It is compact and connects
to a PC via a USB cable.
Once the desktop reader is connected to a PC and the Log-IC Interface Application is open, hold the tag within two
inches of the DTR. Be sure that the desktop reader is not near or on any metal objects (file cabinets, etc.) as this will
cause interference with the RF signal. Do not leave a tag on the DTR for extended periods of time as this will damage
the recorder.