SSV Works WP3-PN304A User manual

WP3-PN3O4A
Honda Pioneer 1000
4 Speaker Overhead WP System
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by
a limited 1 year warranty against defects in material or workmanship. All SSV
Works Speakers are covered by a limited 1 year warranty against defects in
material or workmanship. Labor for replacement of defective components is
not covered. Contact SSV Works for further warranty information.
1. WP3-PN3O4A x 1
2. M6 Screw x12
3. M6 Washers x16
4. Lock Nuts x4
5. 30mm Hex bolts x2
6. Aluminium Spacer x2
TOOLS NEEDED FOR INSTALLATION
INSTALLATION NOTES
PARTS LIST
PARTS LIST IMAGES
7. Enclosure Mounting Bracket x2
8. J Mounting Brackets x 2
9. J Bracket Rubber Insert x2
10. Fuse Holder with Fuse
11. Crimp on ring terminal
12.Zip Ties
To make wiring easier, locate the battery in the vehicle before
beginning the installation. The use of a thread locker is
recommended on all screws to prevent loosening due to vibration. If
the vehicle has a roof, it will need to be removed prior to installation.
Once the installation of the WP3-PN3O4A is complete the roof may be
re-installed, modication to the roof may be required for proper t.
2. M6 Screws x 12 3. M6 Washers x 16
10. Fuse Holder with
Fuse
9. J Bracket Rubber
Instert x2
7. Enclosure Mounting
Brackets x 2
8. J Mounting Bracket
5. 30mm Hex Bolts x24. Lock Nuts x4 6. Aluminimum
Spacer x2
11. Crimp on ring
terminal
12. Zip ties
1. WP3-PN3O4A
- 4mm Hex Key
- #3 Philips Screw Driver
- 10mm Socket and Ratchet
- Strippers and Crimppers
Be sure to pre-install the J
Bracket Rubber inserts before
installing the WP3-PN3O4A

A. Loosely install the (2) mounting brackets onto the top of the
enclosure using (8) Phillips Screws and (8) washers. Brackets are
marked with a D (driver) or P (passenger) for correct orientation.
C. Place the WP3-PN3O4A onto the cage with the (2) J style brackets
resting on the front of the cage.
B. The enclosure brackets will utilize one safety net bolt on each side.
Remove both with a 10mm socket.
D. While holding the enclosure in position use the supplied 30mm hex
bolt (1) aluminum spacer and factory washer to secure the PN3O4
bracket to the safety net bracket. Do not tighten it all the way.
Repeat these steps on the opposing side.
E. Install both bottom J Brackets using (4) Phillips screws (8) Washers
and (4) lock nuts. Be sure rubber insterts are pre-installed.
WP3-PN3O4A
A
C
E
B
D
A. Cut the power/ground cable to length; be sure to leave
enough wire at the battery location to wire to the battery,
strip back approximately 4 inches of the black tubing to
expose the red/black wires inside.
Strip back 1/4”-1/2” of wire to make your connections.
B. Crimp the supplied
fuse holder onto the
end of the RED wire
and attach to the
battery “+” terminal.
C. Crimp the supplied
ring terminal to
the BLACK wire
and attach to the
battery “-” terminal.
WIRING INSTRUCTIONS
A
B C
© 2018 SSV Works, Oxnard, CA 93030 WP3-PN3O4A Rev. B 2-21-18
F. After all the hardware has been loosely installed, make sure
the enclosure is seated properly then go back and tight on all
the mounting hardware.
Run all necessary cabling to the battery.