SSV DIL/NetPC DNP/8331 Application guide

DIL/NetPC
DNP/
8331
Board Revision 1.0
Hardware Reference
SSV Embedded Systems
Dünenweg 5
D-30419 Hannover
Phone: [phone]
Fax: [phone]
E-mai : sa [email protected]
Document Revision: 1.0
Date: 2022-04-04

DIL/NetPC DNP/8331 – Hardware Reference
2
D oc u m e n t R e v i s i o n 1 . 0
CONTENT
1 INTRODUCTION ............................................................................................................... 3
1.1 Safety Guidelines ................................................................................................................... 3
1.2 Conventions ........................................................................................................................... 3
1.3 Block Diagram ........................................................................................................................ 4
1.4 Features and Tec nical Data ................................................................................................. 5
2 PINOUTS .......................................................................................................................... 7
3.1 DIL-40 Connector – J1 ............................................................................................................ 7
3.2 DIL-40 Connector Function Multiplexing ............................................................................... 8
3 MECHANICAL DIMENSIONS ........................................................................................... 9
4 HELP UL LITERATURE ................................................................................................ 10
CONTACT ............................................................................................................................. 10
DOCUMENT HISTORY ......................................................................................................... 10

DIL/NetPC DNP/8331 – Hardware Reference
D o c u m e n t R e v i s i o n 1 . 0
3
1 INTRODUCTION
This document describes the basic hardware components of the DIL/NetPC DNP/8331.
1.1 Safety Guidelines
Please read the following safety guidelines carefully! In case of property or personal
damage by not paying attention to this document and/or by incorrect handling, we do
not assume liability. In such cases any warranty claim expires.
ATTE TIO !
Obser e precautions for handling – electrostatic sensiti e de ice!
• The installation of the de ice should be done only by qualified personnel.
• Discharge yourself before you work with the de ice, e.g. by touching a heater of
metal, to a oid damages.
• Stay grounded while working with the de ice to a oid damage through electrostat-
ic discharge.
1.2 Conventions
Convention
Usage
bold
Important
terms
monospace
Pathnames, filenames, command lines and program code
Table 1: Conventions used in this Document

DIL/NetPC DNP/8331 – Hardware Reference
4
D o c u m e n t R e v i s i o n 1 . 0
1.3 Block Diagram
Figure 1: Block diagram of DIL/ etPC D P/8331

DIL/NetPC DNP/8331 – Hardware Reference
D o c u m e n t R e v i s i o n 1 . 0
5
1.4 Features and Tec nical Data
Processor
Manufacturer / Type
Sochip S3 with ARM Cortex
-
A7 CPU
Clock speed
1008
MHz
Memor
RAM
128 M
B DDR3
SDRAM
Storage media
1x internal microSD card holder
(with pre
-
installed microSD)
Interfaces
Ethernet
1x 10/100 Mbps
USB
1x USB 2.0 host port with max. 480 Mbps
UART
3x UART (COM1 with all hardware handshake signals, COM2
TX/RX only, COM3 TX/RX/RTS/CTS -
functional OR with four
GPIO signals)
SPI
1x SPI master
controller, functional OR with four GPIO signals
I2C
1x I2C master
controller, functional OR with two GPIO signals
GPIO
20
-
bit GPIO (General Purpose Input Output)
Special Functions
Watc
hdog
1x Timer watchdog (hardware
-
based, software
-
configurable)
1x Power super isor (hardware-based)
Displa s / Control Elements
LEDs
1x LAN
link LED
Software
Boot loader
Preinstalled U Boot boot loader
Operating system
Preinstalled Linux operating sys
tem
Electrical Characteristics
Supply voltage
3.3 VDC ±5%
Supply current
300 mA typical / 500 mA max.
Mechanical Characteristics
Socket
40 pin JEDEC DIL 40 connector, 2.54 mm centers
(Pin-compatible to other SSV DIL-40 de ices)
Mass
< 150 g
Dimensio
ns
55 mm x 23 mm
Operating temperature
0 .. 70 °C
Standards and Certifications
EMC
CE
Environmental
standards
RoHS, WEEE
Table 2: Features and technical data

DIL/NetPC DNP/8331 – Hardware Reference
6
D o c u m e n t R e v i s i o n 1 . 0
Figure 2: Board layout DIL/ etPC D P/8331

DIL/NetPC DNP/8331 – Hardware Reference
D o c u m e n t R e v i s i o n 1 . 0
7
2 PINOUTS
3.1 DIL-40 Connector – J1
Please note:
The arrangement of the signals in groups has compatibility reasons. Other prod-
ucts of SSV with DIL-40 pinout are fully or conditionally pin compatible to the
DIL/NetPC DNP/8331 by obser ance of the corresponding application note.
Pin
Name
Group
Function
1
PA0
PIO
Parallel I/O, Port A, Bit 0
2
PA1
PIO
Parallel I/O, Port A, Bit 1
3
PA2
PIO
Parallel I/O, Port A, Bit 2
4
PA3
PIO
Parallel I/O, Port A, Bit 3
5
PA4
PIO
Parallel I/O, Port A, Bit 4
6
PA5
PIO
Parallel I/O, Port A, Bit
5
7
PA6
PIO
Parallel I/O, Port A, Bit 6
8
PA7
PIO
Parallel I/O, Port A, Bit 7
9
PB0
PIO
Parallel I/O, Port B, Bit 0
10
PB1
PIO
Parallel I/O, Port B, Bit 1
11
PB2
PIO
Parallel I/O, Port B, Bit 2
12
PB3
PIO
Parallel I/O, Port B, Bit 3
13
PB4
PIO
Par
allel I/O, Port B, Bit 4
14
PB5
PIO
Parallel I/O, Port B, Bit 5
15
PB6
PIO
Parallel I/O, Port B, Bit 6
16
PB7
PIO
Parallel I/O, Port B, Bit 7
17
RESIN
RESET
Reset Input (Low Acti e)
18
HDMA
USB
USB Host Port
-
19
HDPA
USB
USB Host Port +
20
GND
---
Ground
21
RCM
---
RCM (Remote Console Mode) Input
22
TX+
LAN
10/100 Mbps LAN, TX+ Pin
23
TX
-
LAN
10/100 Mbps LAN, TX
-
Pin
24
RX+
LAN
10/100 Mbps LAN, RX+ Pin
25
RX
-
LAN
10/100 Mbps LAN, RX
-
Pin
26
TXD2
SIO
COM2 Serial Port, TXD Pin
27
RXD2
SIO
COM2
Serial Port, RXD Pin
28
RI1
SIO
COM1 Serial Port, RI Pin
29
DTR1
SIO
COM1 Serial Port, DTR Pin
30
DSR1
SIO
COM1 Serial Port, DSR Pin
Table 3: Pinout DIL-40 connector part 1

DIL/NetPC DNP/8331 – Hardware Reference
8
D o c u m e n t R e v i s i o n 1 . 0
Pin
Name
Group
Function
31
DCD1
SIO
COM1 Serial Port, DCD Pin
32
RTS1
SIO
COM1 Ser
ial Port, RTS Pin
33
CTS1
SIO
COM1 Serial Port, CTS Pin
34
TXD1
SIO
COM1 Serial Port, TXD Pin
35
RXD1
SIO
COM1 Serial Port, RXD Pin
36
PC0
PIO
Parallel I/O, Port C, Bit 0
37
PC1
PIO
Parallel I/O, Port C, Bit 1
38
PC2
PIO
Parallel I/O, Port C, Bit 2
39
PC3
PIO
Parallel I/O, Port C, Bit 3
40
VCC
---
3.3 Volt Power Input
Table 4: Pinout DIL-40 connector part 2
3.2 DIL-40 Connector Function Multiplexing
Some pins of the DIL-40 connector of the DNP/8331 ha e multiple meanings. The pins ha e
a main and an alternate function (function multiplexing).
The main functions correspond with the standard pinout of the DIL-40 connector as shown
in table 2. The alternate functions are shown in table 3 below.
Pin
Name
Main Function
SoC
Signal
Name
Alternate
SoC
Function
1
PA0
Parallel I/O, Port A, Bit 0
PG0 (SDC1_CLK)
SD Card Clock
2
PA1
Parallel I/O, Port A, Bit 1
PG1 (SDC1_CMD)
SD Card Command
3
PA2
Parallel I/O, Port A, Bit 2
PG2 (SDC1_D0)
SD Card Data Bit 0
4
PA3
Parallel I/O, Port A, Bit 3
PG3 (SDC1_D1)
SD Card Data Bit
1
5
PA4
Parallel I/O, Port A, Bit 4
PG4 (SDC1_D2)
SD Card Data Bit 2
6
PA5
Parallel I/O, Port A, Bit 5
PG5 (SDC1_D3
SD Card Data Bit 3
7
PA6
Parallel I/O, Port A, Bit 6
PE23
---
8
PA7
Parallel I/O, Port A, Bit 7
PE24
---
9
PB0
Parallel I/O, Port B, B
it 0
PB0 (UART2_TX)
COM3 Serial Port, T
XD
10
P
B
1
Parallel I/O, Port B, Bit 1
PB1 (UART2_RX)
COM3 Serial Port, RXD
11
P
B
2
Parallel I/O, Port B, Bit 2
PB2 (UART2_RTS)
COM3 Serial Port, RTS
12
PB
3
Parallel I/O, Port B, Bit 3
PB3 (UART2_CTS)
COM3 Serial Por
t, CTS
13
PB
4
Parallel I/O, Port B, Bit 4
PE21 (TWI1_CLK)
I2C Clock
14
PB
5
Parallel I/O, Port B, Bit 5
PE22 (TWI1_SDA)
I2C Data
15
PB
6
Parallel I/O, Port B, Bit 6
PB4
---
16
PB
7
Parallel I/O, Port B, Bit 7
PB5
---
36
PC0
Parallel I/O, Port C, Bit 0
PC
3 (SPI
0
_MOSI)
SPI MOSI
37
PC1
Parallel I/O, Port C, Bit 1
PC0 (SPI
0
_MISO)
SPI MISO
38
PC2
Parallel I/O, Port C, Bit 2
PC1 (SPI
0
_CLK)
SPI Clock
39
PC3
Parallel I/O, Port C, Bit 3
PC2 (SPI
0
_CS0)
SPI Chip Select 0
Table 5: D P/8331 function multiplexing

DIL/NetPC DNP/8331 – Hardware Reference
D o c u m e n t R e v i s i o n 1 . 0
9
3 MECHANICAL DIMENSIONS
All length dimensions ha e a tolerance of 0.5 mm.
Figure 3: Mechanical dimensions of DIL/ etPC D P/8331

DIL/NetPC DNP/8331 – Hardware Reference
10
D o c u m e n t R e v i s i o n 1 . 0
4 HELPFUL LITERATURE
• Sochip S3 datasheet
CONTACT
SSV Software Systems GmbH
Dünenweg 5
D-30419 Hanno er
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Internet: www.ssv-embedded.de
Forum: www.ssv-comm.de/forum
LinkedIn: www.linkedin.com/company/ssv-software-systems
DOCUMENT HISTORY
Revision
Date
Remarks
Name
R
eview
1.0 2022-04-04 first version WBU SSC
The content of this document can change any time without an
nouncement. There is taken over no guaran-
tee for the accuracy of the statements. The user assumes the entire risk as to the accuracy an
d the use of
this document. Information in this document is provided ‘as is’ without warranty of any kind. Some names
within this document can be trademarks of their respective holders.
© 2022 SSV SOFTWARE SYSTEMS GmbH. All rights reserved.