Stadium Boston MS0640 User manual

Boston - Display Cabinet
Dimensions
Width - 92cm
Depth - 24cm
Height - 123.5cm
Issue 1 - 27/03/2015
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts,
email us at techstyle.spar[email protected]
Assembly Instructions - Please keep for future reference
MS0641
MS0642
MS0640

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Do not place very hot or cold
items on the glass surface(s)
unless adequately thick table
mats or coasters are used to
prevent such items from coming
into contact with the glass
• Do not sit or stand upon the
glass.
• Do no use the glass as a
chopping surface.
• Do no strike the glass with
hard or pointed items.
• When cleaning glass panels
use a damp cloth or leather
with washing up liquid or soft
soap if necessary: do not
use washing powders or any
other substances containing
abrasives since these
substances scratch glass.
Glass care and maintenance
Tools required
Crosshead screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)

Components
Please check you have all the panels and fittings listed below
2
A
If you have damaged or missing components,
email us at [email protected]
F
G
G
B
C
D
H
H
H
H
H
H
E
Camlock nut x 4
1
Wooden dowel x 8
5
Camlock bolt x 4
2
Glue x 1
8
Large screw x 6
3
Wall fixing kit x 2
9
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Tack x 28
6
Screw x 4
4
Shelf support x 24
7

3
Assembly Instructions
Step 1
Assemble frame
a: Insert 4 x wooden
dowel 5, 2 in each end,
into fixed shelf E.
Insert 1 x camlock bolt
2into left side D.
Insert 1 x camlock nut 1
into fixed shelf Ewith
the arrow pointing to the
nearest edge.
Rotate the camlock nuts
1clockwise for about
1/4 to 1/2 a turn or until
the bolt “connects” with
the screw and is secure.
b: Insert 2 x camlock
bolt 2into top A.
c: Insert 2 x wooden
dowel 5into left side
D. Repeat for right side
C.
Attach left side Dand
right side Cto top A.
Insert 1 x camlock nut
1into left side Dwith
the arrow pointing to the
nearest edge. Repeat for
right side C
Rotate the camlock nuts
1clockwise for about
1/4 to 1/2 a turn or until
the bolt “connects” with
the screw and is secure.
a:
1
2
2
1
1
b:
c:
5.X4
E
D
C
A
D
C
A
1
1
2
2
5
1
2
2
1
1
5
5

4
Assembly Instructions
Step 1 cont.
Assemble frame
d: Attach base Bto
assembled frame using
6 x large screws 3as
shown.
e: Place unit on its front.
To attach the back panel
Fto the back of the
assembled frame make
sure that the wood eect
side is facing inwards.
Fix the back panel Fto
the sides, top and base
as shown using 28 x tack
6.
Fix the back panel Fto
the fixed shelf as shown
using 4 x small screw 4.
Move unit upright to sit
on the base B.
3.X6
44
4
4
d:
e:
B
D
C
F
3
3
6
6
6
4
4
4
4
Note: Start with the
corners and keep
checking that the
unit is square before
adding the remaining
tacks.

Assembly Instructions
Step 2
Adding shelves
Warning:
Handle glass
shelves with care
f: Insert 4 x shelf
support 7into level
holes - two on each
side of the desired shelf
position.
Insert glass shelf H
resting it on the shelf
supports 7. Do this for
each of the six shelves.
The shelf supports can
be repositioned at any
time to give taller or
shorter shelves.
Adding doors
Warning:
Handle glass
doors with care
g: Slot glass door panel
Ginto the assembled
frame by gently pushing
upwards into the top
groove and resting
downwards into the
bottom groove.
5
7.X24
Warning:
handle
glass
with care
f:
g:
A
D
H
H
H
H
H
G
G
7
Step 3
Note: make sure
the item is sitting on
its base and on a
level surface before
adding the glass
doors.
Note: the grooves
the doors sit in are
shallower in the
base than the top
to enable the door
to slot in easily but
be held within the
frame.

6
If you need any help or have damaged or missing parts, email techstyle.spar[email protected]
Techstyle Spares, Stadium North, Tofts Farm Industrial Estate, Brenda Road, Hartlepool, TS25 2DH
Assembly Instructions
Step 4
Attaching to the wall
For added security you
can attach this unit to
your wall using wall strap
and fixings kit 9.
Measure the distance
between two suitable
securing positions on
the rear of the cabinet.
Transpose these
measurements to the
wall making sure the
marks are level.
Drill holes suitable for
your wall plugs. Tap wall
plugs into drilled holes.
Attach unit to wall using
2 x wall fixing straps 9.
Note: make sure you
use wall plugs suitable
for your type of wall.
Assembly is complete.
9
A
9

A Guide to - Wall Mounting & Fixings
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety:
and location to ensure your safety
in and around the home.
Fitting: From time to time check
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.