Stamps.com P2 User manual


Stamps.comP2Printer



InstallationGuide


InstallingtheprinterdriverviaUSB
1. Unzipthefile“InstallP2v4.zip”toatemporaryfolder(forexamplec:\InstallP2v4\drivers)
2. Attachthepowercabletothepoweradapter
3. PlugthepoweradapterintotheDCpowerconnectoronthebackoftheprinter.Plug
theotherendofthepowercableintoapoweroutlet
4. Connectthescaletothecomputerbyattachingthe“A”endoftheUSBcabletoyour
computerandthe“B”endoftheUSBcabletotheprinter.
5. TurntheprinteronusingtheOn/Offbuttononthefrontoftheprinter.Youwill
seeaseriesofmessagesonyourcomputerscreenthatindicatetheprinterhasbeen
detectedbyyourcomputer.The“FoundNewHardware”wizardwilllaunch
automaticallytoinstalltheprinterdriver
6. Pointthewizardtothetemporaryfolderwherethefileswereextracted
(c:\InstallP2v4\drivers).Click
7. Click“ContinueAnyway”.Thedriverfileswillbecopiedautomatically.

LoadingPaper
1. SwitchPrinterOFF
2. Opentheprinterlid
3. Putpaperinspoolmakingsurethepaperholeisontheleftside
4. Putspoolbackintotheprinter.Pullthepaperandmakeitpassunderpaperguides.


5. Closethelid
6. SwitchthePrinterON
7. PresstheAdvancebuttontopositionthepaper
PrintingviaUSB
1. OpentheMSWordfileP2Test.doc
2. FromMSWord,clickFilePrint.Select“Stamps.comP2Printer”

3. ClickOK

ConfiguringLAN
TheprinterdoesnotsupportautomaticIPaddressingorDHCP,itmustbeconfiguredwitha
staticIPaddress.The2FCCsamplesareshippedwiththefollowingconfiguration

IP address: 192.168.0.130
TCP port: 1024
Netmask: 255.255.255.0
Gateway: 192.168.0.1
TochangetheLANsettings,installtheLANSettingConfigurationWindowssoftware
Unzipthefile“lansettings.zip”toafolderand“Run”the“setup.exe”andclick“Next”when
prompted.
Theprintermustbeputinto“ISPMode”(In‐SystemProgramming)inordertochangetheLAN
settings.Followtheinstructionbelowtodoso.
1. Unplugtheprinteradaptorfromthemains.
2. ConnecttheprintertothecomputerusingaUSBcable.
3. Plugtheadaptorbackintothemains.DonotpresstheON/OFFbutton.
4. Puttheprinterinto“ISPMode”byholdingtheAdvancebuttondown(donotreleaseyet)and
thenpressON/OFFbutton.ReleasetheAdvancebutton.TheBlueLEDontheAdvancebutton
willblinktodenotethattheprinterisin“ISPMode”.
Clickonthe“PrinterLanSet”linktoopenthesoftwareandchangetheLANsettings.
 
NOTE:PleasedonotchangetheTCPPortdefaultvalue=1024


Click“Save”buttontoconfirmchange.

InstallingtheLANPrinter
InstallingtheLANprinterinWindowsXP:
1. OpenaDOSpromptandgotothedriversdirectory

2. Type“installp2v4 ipaddress”whereipaddressistheIPaddressthatyou
haveused(forexampleinstallp2v4 192.168.0.138)
3. PressEnterkey
4. TheprinterwillbeinstalledasStamps.comP2Printer(LAN)


PrintingviaLAN
1. OpentheMSWordfileP2Test.doc
2. FromMSWord,clickFilePrint.Select“Stamps.comP2Printer(LAN)”


3. ClickOK

PrinterWebserver
Openabrowserandentertheaddresshttp://192.168.0.138toviewthe
printer’ssimplewebserver.

FCCStatement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonable
protectionagainstharmfulinterferencewhentheequipmentisoperatedinacommercial
environment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,if
notinstalledandusedinaccordancewiththeinstructionmanual,maycauseharmful
interferencetoradiocommunications.Operationofthisequipmentinaresidentialareaislikely
tocauseharmfulinterferenceinwhichcasetheuserwillberequiredtocorrecttheinterference
athisownexpense.

FCCCaution
Anychangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliance
couldvoidtheuser’sauthoritytooperatethisequipment.


FCCWarning
ThisequipmenthasbeentestedandfoundtocomplywiththeregulationsforaClassBdigital
device,pursuanttoPart15oftheFCCRules.
Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference.
(2)Thisdevicemustacceptanyinterferencereceivedincludinginterferencethatmaycause
undesiredoperation.
