Stan's NoTubes OE Series Manual

NEEDED:
Stan’s NoTubes ZTR wheel set, 2 tires,
Stan’s NoTubes Tire Sealant, core remover
tool, injector or 2 oz. bottle, floor pump or
compressor, soapy water, safety goggles.
IMPORTANT NOTE:
Never inflate any tire without a tube above
40psi unless it is specifically labeled for
tubeless use. Maximum pressure listed on
your rims may differ from maximum pressure
listed on your tires. Do not inflate above the
lower of the two numbers.
WARNING:
Always wear safely goggles, Sealant can
stain clothes or furniture.
Mount tire: Making sure to position the tire bead
in the center channel of the rim, mount one tire
bead beginning opposite the valve and finishing
at the valve. Once the first bead is mounted begin
mounting the second bead opposite the valve and
finish at the valve.
With a brush or sponge apply a generous amount
of soapy water to both beads of the tire to help it
slip onto the bead of the rim when inflating.
Rotate the valve to 12 o’clock and install a pump.
Inflate tire to 35psi to seat tire.
Add sealant: Once successful with inflation remove
the valve core to add Stan’s sealant. Add 2–4 oz.
of sealant.
1
Inflate to preferred riding pressure. Always review the maximum
pressure information listed on both the rim and the tire and
consider the lower of the two numbers your maximum pressure.
Do not inflate above the lower of the two numbers.
5
6
2
3
4Lay tire on side and apply a thin sheen of soapy water around the
sidewall and the bead area. Look for suds occurring anywhere on
the tire or bead area. Suds bubbling out from the tire indicate
porous areas. Shake the sealant to those areas to seal them and
apply soap and water again. Check for suds forming on both sides
of the tire. Repeat until no suds remain. Install the cassette and
rotors according to the component manufacturer's recommendations.
7
YES
NO
Bounce: hold the wheel vertically and gently bounce or "dribble"
it to disperse the sealant throughout the inside of the tire. Let it
drop from an inch or two, then rotate a few degrees and repeat.
Do this for several revolutions of the wheel.
INSTRUCTION GUIDE : OE SERIES WHEELS

EIS-036 Stan's NoTubes OE Series Aluminum Rim Setup Guide
NOTUBES.COM 202 Daniel Zenker Dr., Big Flats, NY14814 [phone] [email protected]
*REQUIRES TWO LAYERS OF TAPE
NA/NA/537/561/598g
NA/NA/524/548/584g
NA/NA/452/472/504g
NA/NA/388/406/433g
NA/NA/524/548/584g
NA/NA/553/578/616g
NA/NA/NA/NA/490g
319/400/NA/458/488g
365/458/NA/524/559g
NA/NA/NA/594/634g
TAPE
WIDTH
36mm
39mm
33mm
30mm
27mm
25mm
25mm*
25mm
27mm
30mm
125
125
125
125
125
125
125
125
125
125
STAN’S
BUILD
TENSION (KgF)
35mm
35mm
35mm
35mm
35mm
35mm
44mm
35mm
35mm
35mm
VALVE
125
125
125
125
125
125
125
125
125
125
MAX
SPOKE
TENSION (KgF)
NA/NA/539/564/602
NA/NA/539/564/602
NA/NA/541/566/604
NA/NA/541/566/604
NA/NA/541/566/604
NA/NA/539/564/602
NA/NA/NA/NA/590
388/489/NA/566/604
388/489/NA/565/604
NA/NA/NA/566/604
ERD
20/24/26/27.5/29
WEIGHT
20/24/26/27.5/29
Baron S1
Major S1
Sentry S1
Flow S1
Arch S1
Crest S1
Flow D
Arch D
Crest D
Grail S1
RIMS
STAN’S NOTUBES OE SERIES ALUMINUM
RIM SETUP GUIDE
26.0
17.3
29.7
23.0
17.2
26.6
29.0
17.6
33.1
32.0
18.7
35.7
35.0
18.7
38.7
CREST S1 ARCH S1 FLOW S1 SENTRY S1 BARON S1
38.0
18.4
41.7
20.3
24.5
24.1
23.0
17.5
26.6
26.0
17.5
29.3
29.0
17.5
32.7
MAJOR S1
GRAIL S1
CREST D ARCH D FLOW D
Stan's rims are optimized for tubeless use and designed to set up tubeless with Stan’s Yellow Tape, Universal Valves, and Tire Sealant.
Tubes may also be used on all Stan’s rims; as with all tube installations, care must be taken to prevent tubes from being caught underneath the
bead of the tire, causing the tire to dismount when inflated.
Stan’s NoTubes Yellow Rim Tape is designed for use with all Stan’s rims. Use of other tapes is not recommended. BST rims require
Important: Never inflate any tire without a tube above 40psi unless it is specifically labeled for tubeless use. Maximum
pressure listed on your rims may differ from maximum pressure listed on your tires. Do not inflate above the lower of the two numbers.
Warranty: Warranty policies for aluminum rims can be found at: https://www.notubes.com/warranty-info
NOTE: ALL RIMS ARE DESIGNED FOR DISC BRAKE USE ONLY
one layer of Yellow Tape; BST-R rims require two layers. See above chart for tape width. Tape installation and additional how-to videos are available
at: https://www.notubes.com/help