Stanley STFP00020 User manual

Instruction manual
Manuel d'instructions
Manual de'instrucciones
www.StanleyTools.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
STFP00020
Air Compressor
Compresor de aire
Compresseur d’air
Maintenance-free pump
La pompe sans entretien
La bomba sin mantenimiento
Part No. N439650 MAY15 Copyright ©2015 STANLEY TOOLS
Final size: 210mm x 145mm

2 - ENG
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information
relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize
this information, we use the symbols below. Please read the manual and pay attention to these symbols.
Indicates an imminently
hazardous situation which, if not avoided, will
result in death or serious injury.
Indicates a potentially
hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a potentially
hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a practice not
related to personal injury which, if not
avoided, may result in property damage.
IMPORTANT SAFETY INSTRUCTIONS
This product contains chemicals known to the State of California to cause cancer,
and birth defects or other reproductive harm. Wash hands after handling.
Some dust contains chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm such as asbestos and lead in lead based paint.
To reduce the risk of injury, read the instruction manual.
SAVE THESE INSTRUCTIONS
HAZARD
RISK OF EXPLOSION OR FIRE
WHAT CAN HAPPEN HOW TO PREVENT IT
• It is normal for electrical contacts within the
motor and pressure switch to spark. • Always operate the compressor in a well ventilated area free of combustible materials,
gasoline, or solvent vapors.
• If electrical sparks from compressor come into
contact with flammable vapors, they may ignite,
causing fire or explosion.
• If spraying flammable materials, locate
compressor at least 20' (6.1 m) away from
spray area.An additional length of air hose may
be required.
• Store flammable materials in a secure location
away from compressor.
• Restricting any of the compressor ventilation
openings will cause serious overheating and
could cause fire.
• Never place objects against or on top of
compressor.
• Operate compressor in an open area at least 12"
(30.5 cm) away from any wall or obstruction
that would restrict the flow of fresh air to the
ventilation openings.
• Operate compressor in a clean, dry well
ventilated area. Do not operate unit in any
confined area. Store indoors.
• Unattended operation of this product could
result in personal injury or property damage.
To reduce the risk of fire, do not allow the
compressor to operate unattended.
• Always remain in attendance with the product
when it is operating.
• Always turn off and unplug unit when not in
use.

3 - ENG
HAZARD
RISK TO BREATHING (ASPHYXIATION)
WHAT CAN HAPPEN HOW TO PREVENT IT
• The compressed air directly from your
compressor is not safe for breathing. The air
stream may contain carbon monoxide, toxic
vapors, or solid particles from the air tank.
Breathing these contaminants can cause serious
injury or death.
• Never use air obtained directly from
the compressor to supply air for human
consumption. The compressor is not equipped
with suitable filters and in-line safety equipment
for human consumption.
• Exposure to chemicals in dust created by power
sanding, sawing, grinding, drilling, and other
construction activities may be harmful.
• Sprayed materials such as paint, paint solvents,
paint remover, insecticides, weed killers, may
contain harmful vapors and poisons.
• Work in an area with good cross ventilation.
Read and follow the safety instructions
provided on the label or safety data sheets
for the materials you are spraying. Always
use certified safety equipment: NIOSH/OSHA
respiratory protection or properly fitting face
mask designed for use with your specific
application.
HAZARD
RISK OF BURSTING
Air Tank: On February 26, 2002, the U.S. Consumer Product Safety Commission published
Release # 02-108 concerning air compressor tank safety:
Air compressor receiver tanks do not have an infinite life. Tank life is dependent upon several
factors, some of which include operating conditions, ambient conditions, proper installations, field
modifications, and the level of maintenance. The exact effect of these factors on air receiver life is
difficult to predict.
If proper maintenance procedures are not followed, internal corrosion to the inner wall of the air
receiver tank can cause the air tank to unexpectedly rupture allowing pressurized air to suddenly and
forcefully escape, posing risk of injury to consumers.
Your compressor air tank must be removed from service by the end of the year shown on your tank
warning label.
The following conditions could lead to a weakening of the air tank, and result in a violent air tank
explosion:
WHAT CAN HAPPEN HOW TO PREVENT IT
• Failure to properly drain condensed water from
air tank, causing rust and thinning of the steel
air tank.
• Drain air tank daily or after each use. If air tank
develops a leak, replace it immediately with a
new air tank or replace the entire compressor.
• Modifications or attempted repairs to the
air tank. • Never drill into, weld, or make any modifications to the air tank or its attachments. Never attempt
to repair a damaged or leaking air tank. Replace
with a new air tank.
• Unauthorized modifications to the safety valve
or any other components which control air tank
pressure.
• The air tank is designed to withstand specific
operating pressures. Never make adjustments
or parts substitutions to alter the factory set
operating pressures.

4 - ENG
ATTACHMENTS & ACCESSORIES:
• Exceeding the pressure rating of air tools, spray
guns, air operated accessories, tires, and other
inflatables can cause them to explode or fly
apart, and could result in serious injury.
• Follow the equipment manufacturers
recommendation and never exceed the
maximum allowable pressure rating of
attachments. Never use compressor to inflate
small low pressure objects such as children’s
toys, footballs, basketballs, etc.
TIRES:
• Over inflation of tires could result in serious
injury and property damage. • Use a tire pressure gauge to check the tires pressure before each use and while inflating
tires; see the tire sidewall for the correct tire
pressure.
NOTE: Air tanks, compressors and similar
equipment used to inflate tires can fill small
tires very rapidly. Adjust pressure regulator on
air supply to no more than the rating of the
tire pressure. Add air in small increments and
frequently use the tire gauge to prevent over
inflation.
HAZARD
RISK OF ELECTRICAL SHOCK
WHAT CAN HAPPEN HOW TO PREVENT IT
• Your compressor is powered by electricity. Like
any other electrically powered device, if it is not
used properly it may cause electric shock.
• Never operate the compressor outdoors when it
is raining or in wet conditions.
• Never operate compressor with protective
covers removed or damaged.
• Repairs attempted by unqualified personnel can
result in serious injury or death by electrocution. • Any electrical wiring or repairs required on this product should be performed by authorized
service center personnel in accordance with
national and local electrical codes.
• Electrical Grounding: Failure to provide
adequate grounding to this product could result
in serious injury or death from electrocution.
Refer to Grounding Instructions paragraph in
the Installation section.
• Make certain that the electrical circuit to
which the compressor is connected provides
proper electrical grounding, correct voltage and
adequate fuse protection.
HAZARD
RISK FROM FLYING OBJECTS
WHAT CAN HAPPEN HOW TO PREVENT IT
• The compressed air stream can cause soft tissue
damage to exposed skin and can propel dirt,
chips, loose particles, and small objects at high
speed, resulting in property damage or personal
injury.
• Always wear certified safety equipment: ANSI
Z87.1 eye protection (CAN/CSA Z94.3) with side
shields when using the compressor.
• Never point any nozzle or sprayer toward any
part of the body or at other people or animals.
• Always turn the compressor off and bleed
pressure from the air hose and air tank before
attempting maintenance, attaching tools or
accessories.

5 - ENG
HAZARD
RISK OF HOT SURFACES
WHAT CAN HAPPEN HOW TO PREVENT IT
• Touching exposed metal such as the compressor
head, engine head, engine exhaust or outlet
tubes, can result in serious burns.
• Never touch any exposed metal parts on
compressor during or immediately after
operation. Compressor will remain hot for
several minutes after operation.
• Do not reach around protective shrouds or
attempt maintenance until unit has been
allowed to cool.
HAZARD
RISK FROM MOVING PARTS
WHAT CAN HAPPEN HOW TO PREVENT IT
• Moving parts such as the pulley, flywheel, and
belt can cause serious injury if they come into
contact with you or your clothing.
• Never operate the compressor with guards or
covers which are damaged or removed.
• Keep your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
• Air vents may cover moving parts and should be
avoided as well.
• Attempting to operate compressor with
damaged or missing parts or attempting to
repair compressor with protective shrouds
removed can expose you to moving parts and
can result in serious injury.
• Any repairs required on this product should
be performed by authorized service center
personnel.
HAZARD
RISK OF UNSAFE OPERATION
WHAT CAN HAPPEN HOW TO PREVENT IT
• Unsafe operation of your compressor could lead
to serious injury or death to you or others. • Review and understand all instructions and warnings in this manual.
• Become familiar with the operation and controls
of the air compressor.
• Keep operating area clear of all persons, pets,
and obstacles.
• Keep children away from the air compressor at
all times.
• Do not operate the product when fatigued or
under the influence of alcohol or drugs. Stay
alert at all times.
• Never defeat the safety features of this product.
• Equip area of operation with a fire extinguisher.
• Do not operate machine with missing, broken,
or unauthorized parts.
• Never stand on the compressor.

6 - ENG
HAZARD
RISK OF FALLING
WHAT CAN HAPPEN HOW TO PREVENT IT
• A portable compressor can fall from a table,
workbench, or roof causing damage to the
compressor and could result in serious injury or
death to the operator.
• Always operate compressor in a stable secure
position to prevent accidental movement of the
unit. Never operate compressor on a roof or
other elevated position. Use additional air hose
to reach high locations.
HAZARD
RISK FROM NOISE
WHAT CAN HAPPEN HOW TO PREVENT IT
• Under some conditions and duration of use,
noise from this product may contribute to
hearing loss.
• Always wear proper hearing protection during
use.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
SPECIFICATIONS
Model No. STFP00020
Bore 1.181" (30 mm)
Stroke 0.551" (14 mm)
Voltage/Hz-Single Phase 120/60
Minimum Branch Circuit Requirement 15 amps
Fuse Type Time Delay
Air Tank Capacity 2 Gallon (7.5 liters)
Approximate Cut-in Pressure 85 psig
Approximate Cut-out Pressure 115 psig
SCFM @ 40 psig 0.7 *
SCFM @ 90 psig 0.5 *
Regulated Pressure Rating (Approximate) 3–115 psig
Quick Connect Type 1/4" (6.4 mm) Industrial
*Tested per ISO 1217
Refer to Glossary for abbreviations.
GLOSSARY
Become familiar with these terms before operating the unit.
CFM: Cubic feet per minute.
SCFM: Standard cubic feet per minute; a unit of measure of air delivery.
PSIG: Pounds per square inch gauge; a unit of measure of pressure.
Code Certification: Products that bear one or more of the following marks: UL®, CUL, CULUS, ETL®,
CETL, CETLUS, have been evaluated by OSHA certified independent safety laboratories and meet the
applicable Standards for Safety.
Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When
the tank pressure drops to a certain lower level the motor will restart automatically.The low pressure at which
the motor automatically restarts is called "cut-in" pressure.

7 - ENG
Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank
begins to build. It builds to a certain high pressure before the motor automatically shuts off, protecting
your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called
"cut-out" pressure.
Branch Circuit: Circuit carrying electricity from electrical panel to outlet.
DUTY CYCLE
This air compressor pump is capable of running continuously. However, to prolong the life of your air
compressor, it is recommended that a 50%-75% average duty cycle be maintained; that is, the air
compressor pump should not run more than 30-45 minutes in any given hour.
ASSEMBLY
UNPACKING
Remove unit from carton and discard all packaging.
INSTALLATION
HOW TO SET UP YOUR UNIT
LOCATION OF THE AIR COMPRESSOR
• Locate the air compressor in a clean, dry and well ventilated area.
• The air compressor should be located at least 12" (30.5 cm) away from the wall or other obstructions
that will interfere with the flow of air.
• The air compressor pump and shroud are designed to allow for proper cooling. The ventilation
openings on the compressor are necessary to maintain proper operating temperature. Do not place
rags or other containers on or near these openings.
GROUNDING INSTRUCTIONS (FIG. 1)
RISK OF ELECTRICAL SHOCK. In the event of a short circuit, grounding
reduces the risk of shock by providing an escape wire for the electric current. This air
compressor must be properly grounded.
The portable air compressor is equipped with a cord
C
A
B
FIG. 1
having a grounding wire with an appropriate grounding
plug (A).
1. The cord set and plug (A) with this unit contains a
grounding pin (B). This plug MUST be used with a
grounded outlet (C).
IMPORTANT: The outlet being used must be installed
and grounded in accordance with all local codes and
ordinances.
2. Make sure the outlet being used has the same
configuration as the grounded plug. DO NOT USE AN ADAPTER. See figure 1.
3. Inspect the plug and cord before each use. Do not use if there are signs of damage.
4. If these grounding instructions are not completely understood, or if in doubt as to whether the
compressor is properly grounded, have the installation checked by a qualified electrician.
RISK OF ELECTRICAL SHOCK. IMPROPER GROUNDING CAN RESULT IN
ELECTRICAL SHOCK.
Do not modify the plug provided. If it does not fit the available outlet, a correct outlet should
be installed by a qualified electrician.
Repairs to the cord set or plug MUST be made by a qualified electrician.

8 - ENG
EXTENSION CORDS
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept
the plug on the product
• in good condition
• no longer than 50' (15.2 m)
• 14 gauge (AWG) or larger. (Wire size increases as gauge number decreases. 12 AWG and 10AWG
may also be used. DO NOT USE 16 OR 18 AWG.)
Risk of Property Damage. The use of an undersized extension cord will cause
voltage to drop resulting in power loss to the motor and overheating. Instead of using an
extension cord, increase the working reach of the air hose by attaching another length of hose to its end.
Attach additional lengths of hose as needed.
VOLTAGE AND CIRCUIT PROTECTION
Refer to Specifications for the voltage and minimum branch circuit requirements.
Risk of Overheating. Certain air compressors can be operated on a 15 amp circuit if
the following conditions are met.
1. Voltage supply to circuit must comply with the National Electrical Code.
2. Circuit is not used to supply any other electrical needs.
3. Extension cords comply with specifications.
4. Circuit is equipped with a 15 amp circuit breaker or 15 amp time delay fuse.
NOTE: If compressor is connected to a circuit protected by fuses, use only time delay fuses. Time
delay fuses should be marked "D" in Canada and "T" in the US.
If any of the above conditions cannot be met, or if operation of the compressor repeatedly causes
interruption of the power, it may be necessary to operate it from a 20 amp circuit. It is not necessary to
change the cord set.
OPERATION
KNOW YOUR AIR COMPRESSOR
READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the
illustrations with your unit to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.
DESCRIPTION OF OPERATION (FIG. 2–4)
FIG. 2 D
H
I
E
G

9 - ENG
Become familiar with these controls before operating the unit.
On(I)/Off(O) Switch (D): Place this switch in the On (I) position to provide automatic power to the
pressure switch and Off (O) to remove power at the end of each use.
Pressure Switch (not shown): The pressure switch automatically starts the motor when the air tank
pressure drops below the factory set "cut-in" pressure. It stops the motor when the air tank pressure
reaches the factory set "cut-out" pressure.
Safety Valve (H): If the pressure switch does not shut off the air compressor at its "cut-out" pressure
setting, the safety valve will protect against high pressure by "popping out" at its factory set pressure
(slightly higher than the pressure switch "cut-out" setting).
Tank Pressure Gauge (I): The tank pressure gauge indicates the reserve air pressure in the tank.
Outlet Pressure Gauge (E): The outlet pressure gauge indicates the air pressure available at the outlet
side of the regulator. This pressure is controlled by the regulator and is always less than or equal to the
tank pressure.
Regulator (G): Controls the air pressure shown on the outlet pressure gauge. Turn regulator knob
clockwise to increase pressure and counterclockwise to decrease pressure.
Cooling System (not shown): This compressor contains an advanced design cooling system. At the
heart of this cooling system is an engineered fan. It is perfectly normal for this fan to blow air through
the vent holes in large amounts. You know that the cooling system is working when air is being expelled.
Air Compressor Pump (not shown):Compresses air into the air tank.Working air is not available until
the compressor has raised the air tank pressure above that required at the air outlet.
Drain Valve (K): The drain valve is located at the base of the air tank and is used to drain condensation
at the end of each use.
K
FIG. 3 FIG. 4
F
Check Valve (not shown): When the air compressor is operating, the check valve is "open", allowing
compressed air to enter the air tank.When the air compressor reaches "cut-out" pressure, the check valve
"closes", allowing air pressure to remain inside the air tank.
Motor Overload Protector (not shown): The motor has a thermal overload protector. If the motor
overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to
cool down before restarting. To restart:
1. Set the On/Off switch to "Off" and unplug unit.
2. Allow the motor to cool.
3. Plug the power cord into the correct branch circuit receptacle.
4. Set the Auto/Off switch to "On" position.
Motor Fuse Protector (not shown): The motor is provided with a fuse protector which may cause the
motor to shut off if motor current is too high. If the motor does not operate, follow the instructions under
Motor Overload Protector. If the motor fails to restart after following these instructions, return the unit
to a service center to have the fuse protector replaced. The fuse protector is not a customer serviceable
part.
Quick-Connect Body (F): The quick connect body accepts industrial quick connect plugs.
HOW TO USE YOUR UNIT (FIG. 2)
HOW TO STOP
1. Set the On/Off switch (D) to "Off".
2. Unplug unit when not in use.

10 - ENG
BEFORE STARTING
Do not operate this unit until you read this instruction manual for safety,
operation and maintenance instructions.
BEFORE EACH START-UP
1. Set the On/Off switch (D) to "Off".
2. Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit
Protection paragraph in the Installation section of this manual.)
3. Turn the regulator knob (G) counterclockwise to set the outlet pressure to zero.
4. Attach hose and accessories.
Risk of unsafe operation. Firmly grasp air hose in hand when installing or
disconnecting to prevent hose whip.
Risk of unsafe operation. Do not use damaged or worn accessories.
NOTE: The hose or accessory will require a quick connect plug if the air outlet is equipped with a quick
connect body (F).
Risk of Bursting. Too much air pressure causes a hazardous risk of bursting.
Check the manufacturer’s maximum pressure rating for air tools and accessories. The regulator
outlet pressure must never exceed the maximum pressure rating.
Risk of property damage.Compressed air from the unit may contain water condensation
and oil mist. Do not spray unfiltered air at an item that could be damaged by moisture. Some air tools and
accessories may require filtered air. Read the instructions for the air tools and accessories.
HOW TO START
1. Set the On/Off switch (D) to "On" and allow tank pressure to build. Motor will stop when tank
pressure reaches "cut-out" pressure.
2. Turn regulator knob (G) clockwise to increase pressure and stop when desired pressure is reached.
Risk of unsafe operation. If any unusual noise or vibration is noticed, stop the
compressor immediately and have it checked by a trained service technician.
The compressor is ready for use.
MAINTENANCE
CUSTOMER RESPONSIBILITIES
Before each use Daily or after
each use See tank warning label
Check Safety Valve X
Drain Tank X
Remove tank
from service X1
1- For more information, call our Customer Care Center at 1-800-262-2161
Risk of unsafe operation. Unit cycles automatically when power is on. When
performing maintenance, you may be exposed to voltage sources, compressed air, or moving
parts. Personal injuries can occur. Before performing any maintenance or repair, disconnect
power source from the compressor and bleed off all air pressure.
NOTE: See Operation section for the location of controls.
TO CHECK SAFETY VALVE (FIG. 2)
Risk of Bursting. If the safety valve does not work properly, over-pressurization
may occur, causing air tank rupture or an explosion.

11 - ENG
Risk from Flying Objects. Always wear certified safety equipment: ANSI Z87.1
eye protection (CAN/CSA Z94.3) with side shields.
Before starting compressor, pull the ring on the safety valve (H) to make sure that the safety valve operates
freely. If the valve is stuck or does not operate smoothly, it must be replaced with the same type of valve.
TO DRAIN TANK (FIG. 2, 3)
Risk of Unsafe Operation. Air tanks contain high pressure air. Keep face and
other body parts away from outlet of drain. Use ANSI Z87.1 eye protection (CAN/CSA Z94.3)
when draining as debris can be kicked up into face.
Risk from noise. Always wear proper hearing protection during use. Under
some conditions and duration of use, noise from this product may contribute to hearing loss.
NOTE: All compressed air systems generate condensate that accumulates in any drain point (e.g., tanks, filter,
aftercoolers, dryers). This condensate contains lubricating oil and/or substances which may be regulated and
must be disposed of in accordance with local, state, and federal laws and regulations.
Risk of Bursting. Water will condense in the air tank. If not drained, water will
corrode and weaken the air tank causing a risk of air tank rupture.
Risk of Property Damage. Drain water from air tank may contain oil and rust which
can cause stains.
1. Set the On/Off switch (D) to "Off".
2. Turn the regulator knob (G) counterclockwise to set the outlet pressure to zero.
3. Remove the air tool or accessory.
4. Place a suitable container under the drain valve to catch discharge.
5. Pull ring on safety valve (H) allowing air to bleed from the tank until tank pressure is approximately
20 psi. Release safety valve ring.
6. Drain water from air tank by opening drain valve (K) on bottom of tank.
7. After the water has been drained, close the drain valve. The air compressor can now be stored.
NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then
reinstalled.
SERVICE AND ADJUSTMENTS
ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED
SERVICE TECHNICIAN.
Risk of Unsafe Operation. Unit cycles automatically when power is on. When
servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before
servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of
pressure, and allow the air compressor to cool.
STORAGE
Before you store the air compressor, make sure you do the following:
1. Review the Maintenance section on the preceding pages and perform scheduled maintenance as
necessary.
2. Drain water from air tank. See To Drain Tank under Maintenance.
Water will condense in the air tank. If not drained, water will corrode and
weaken the air tank causing a risk of air tank rupture.
3. Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind
air hose loosely around the compressor handle. Wrap electrical cord onto the cord wrap.
4. Store the air compressor in a clean and dry location.

12 - ENG
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website at
www.stanleytools.com. You can also order parts from your nearest STANLEY Factory Service Center
or STANLEY Authorized Warranty Service Center. Or, you can call our Customer Care Center at
1-800-262-2161.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about
STANLEY, its factory service centers or authorized warranty service centers, visit our website at
www.stanleytools.com or call our Customer Care Center at 1-800-262-2161. All repairs made by our
service centers are fully guaranteed against defective material and workmanship. We cannot guarantee
repairs made or attempted by others.
You can also write to us for information at STANLEY, 4825 Highway 45 North, Jackson, Tennessee 38305
-Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool
(model number, type, serial number, etc.).
ACCESSORIES
Since accessories, other than those offered by STANLEY, have not been tested with
this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only
STANLEY recommended accessories should be used with this product.
A complete line of accessories is available from your STANLEY Factory Service Center or a STANLEY
Authorized Warranty Service Center. Please visit our Web Site www.stanleytools.com for a catalog or for
the name of your nearest supplier.
TROUBLESHOOTING
Risk of Unsafe Operation. Unit cycles automatically when power is on. When
servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before
servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of
pressure, and allow the air compressor to cool.
PROBLEM CAUSE CORRECTION
Excessive tank pressure
- safety valve pops off. Pressure switch does not shut off motor when compressor
reaches "cut-out" pressure.
Move On/Off switch to the "Off"
position, if the outfit does not shut off
contact a Trained Service Technician.
Pressure switch "cut-
out" too high. Contact a Trained Service Technician.
Air leaks at fittings. Tube fittings are not
tight enough. Tighten fittings where air can be heard escaping. Check fittings with soapy
water solution. Do Not Overtighten.
Air leaks in air tank
or at air tank welds. Defective air tank. Air tank must be replaced.
Do not repair the leak.
Risk bursting. Do
not drill into, weld or otherwise
modify air tank or it will weaken.
The tank can rupture or explode.
Air leaks between
head and valve plate. Leaking seal. Contact a Trained Service Technician.

13 - ENG
PROBLEM CAUSE CORRECTION
Air leak from
safety valve. Possible defect in safety valve. Operate safety valve manually by pulling on ring. If valve still
leaks, it should be replaced.
Knocking Noise. Possible defect in safety valve. Operate safety valve manually
by pulling on ring. If valve still
leaks, it should be replaced.
Pressure reading on
the regulated pressure
gauge drops when an
accessory is used.
It is normal for "some"
pressure drop to occur. If there is an excessive amount of pressure drop when the accessory is used, adjust
the regulator following the instructions
in the Description of Operation
paragraph in the Operation Section.
NOTE: Adjust the regulated
pressure under flow conditions
(while accessory is being used).
Compressor is not
supplying enough air to
operate accessories.
Prolonged excessive use of air. Decrease amount of air usage.
Compressor is not large
enough for air requirement. Check the accessory air requirement. If it is higher than the SCFM or pressure
supplied by your air compressor,
you need a larger compressor.
Hole in hose. Check and replace if required.
Check valve restricted. Have checked by a Trained
Service Technician.
Air leaks. Tighten fittings.
Regulator knob has
continuous air leak. Damaged regulator. Replace.
Regulator will not
shut off air outlet. Damaged regulator. Replace.
Motor will not run. Fuse blown, circuit
breaker tripped. Check fuse box for blown fuse and replace as necessary. Reset circuit breaker.
Do not use a fuse or circuit breaker
with higher rating than that specified
for your particular branch circuit.
Check for proper fuse. You should
use a time delay fuse.
Check for low voltage problem.
Check the extension cord.
Disconnect the other electrical
appliances from circuit or operate the
compressor on its own branch circuit.
Extension cord is wrong
length or gauge. Check the extension cord.
Loose electrical connections. Check wiring connection
inside terminal box.
Faulty motor. Have checked by a Trained
Service Technician.
Motor overload protection
switch has tripped. Refer to Motor Overload Protection under Operation. If motor overload
protection trips frequently, contact
a Trained Service Technician.

14 - ENG
FULL ONE YEAR WARRANTY
STANLEY industrial tools are warranted for one year from date of purchase. We will repair, without
charge, any defects due to faulty materials or workmanship. For warranty repair information, call 1-800-
262-2161. This warranty does not apply to accessories or damage caused where repairs have been made
or attempted by others. This warranty gives you specific legal rights and you may have other rights which
vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in
Latin America, see country specific warranty information contained either in the packaging, call the local
company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
1-800-262-2161 for a free replacement.

15 - FR
MESURES DE SÉCURITÉ - DÉFINITIONS
Ce guide contient des renseignements importants que vous deviez bien saisir. Cette information porte sur
VOTRE SÉCURITÉ et sur LA PRÉVENTION DE PROBLÈMES D'ÉQUIPEMENT. Afin de vous aider à identifier
cette information, nous avons utilisé les symboles ci-dessous. Veuillez lire attentivement ce guide en
portant une attention particulière à ces symboles.
Indique un danger imminent
qui, s'il n'est pas évité, causera de graves
blessures ou la mort.
Indique la possibilité d'un
danger qui, s'il n'est pas évité, peut causer des
blessures mineures ou moyennes.
Indique la possibilité
d’un danger qui, s’il n’est pas évité, pourrait
causer de graves blessures ou la mort.
Indique une pratique ne posant
aucun risque de dommages corporels mais qui
par contre, si rien n’est fait pour l’éviter, pourrait
poser des risques de dommages matériels.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Ce produit contient des produits chimiques reconnus par l’État de la
Californie comme étant cancérigènes et pouvant entraîner des anomalies congénitales ou d’autres
problèmes liés aux fonctions reproductrices. Se laver les mains après toute manipulation.
Certaines poussières contiennent des produits chimiques reconnus par
l’État de la Californie comme cancérigènes et pouvant entraîner des anomalies congénitales et d’autres
problèmes liés aux fonctions reproductrices, tels que l’amiante et le plomb contenus dans les peintures
au plomb.
Afin de réduire le risque de blessures, lire le mode
d’emploi de l’outil.
CONSERVER CES DIRECTIVES
DANGER
RISQUE D’EXPLOSION OU D’INCENDIE
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Il est normal que des contacts électriques dans
le moteur et le manocontacteur fassent une
étincelle.
• Faites toujours fonctionner le compresseur dans
une zone bien aérée sans matière combustible,
essence ou vapeur de solvant.
• Si une étincelle électrique provenant du
compresseur entre en contact avec des vapeurs
inflammables, elle peut s’enflammer et causer
un incendie ou une explosion.
• Si vous aspergez des matériaux inflammables,
placez le compresseur à au moins 6,1 m
(20 pieds) de la zone pulvérisée. Il est possible
que vous ayez besoin d’une longueur de tuyau
additionnelle.
• Entreposez les matières inflammables dans un
endroit sécuritaire, éloigné du compresseur.

16 - FR
• Le fait de limiter les ouvertures d’aération
de compresseur causera une importante
surchauffe et pourrait causer un incendie.
• Ne placez jamais des objets contre le
compresseur ou sur celui-ci.
• Faites fonctionner le compresseur dans un
endroit aéré à au moins 30,5 cm (12 po) du
mur ou de l’obstruction qui pourrait limiter le
débit d’air frais dans les ouvertures d’aération.
• Faites fonctionner le compresseur dans un
endroit propre, sec et bien aéré. Ne pas utiliser
l’appareil à dans un endroit exigu. Magasin à
l’intérieur.
• Le fonctionnement de ce produit sans
surveillance pourrait se solder par des
blessures personnelles ou des dommages à la
propriété. Afin de réduire le risque d’incendie,
ne pas laisser le compresseur fonctionner sans
surveillance.
• Être toujours présent lorsque le produit est en
marche.
• Toujours éteindre et débrancher l'appareil si
non utilisé.
DANGER
RISQUE REPIRATOIRE (ASPHYXIE)
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Il est dangereux de respirer l’air comprimé
sortant du compresseur. Le flux d’air peut
contenir du monoxyde de carbone, des
vapeurs toxiques ou des particules solides
provenant du réservoir d’air. La respiration de
ces contaminants peut causer de sérieuses
blessures, voire la mort.
• Ne jamais utiliser l’air obtenu directement du
compresseur pour l’alimentation en air destinée
à la consommation humaine. Le compresseur
n’est pas muni de filtres et d’équipement
de sécurité en ligne qui conviennent à la
consommation humaine.
• Une exposition aux produits chimiques présents
dans la poussière générée par les activités de
ponçage, sciage, meulage, perçage et autres,
peut être nocive.
• Les matériaux vaporisés comme la peinture,
les solvants de peinture, les décapants, les
insecticides, les herbicides, pourraient contenir
des vapeurs nocives et du poison.
• Travailler dans un endroit ayant une bonne
aération transversale. Lire et respecter les
directives en matière de sécurité imprimées
sur l’étiquette ou les fiches signalétiques des
matériaux qui sont pulvérisés. Toujours utiliser
un équipement de sécurité homologué : une
protection respiratoire conforme aux normes
NIOSH/OSHA, ou un masque facial bien ajusté,
conçus spécifiquement pour votre utilisation
particulière.

17 - FR
DANGER
RISQUE D’ÉCLATEMENT
Réservoir d’air comprimé : Le 26 février 2002, la U.S. Consumer Product Safety Commission
américaine a publié la règle nº 02-108 portant sur la sécurité en matière de réservoir d’air comprimé
des compresseurs:
Les réservoirs d’air comprimé des compresseurs n’ont pas une durée de vie illimitée. La durée de vie des
réservoirs dépend de plusieurs facteurs, qui comprennent entre autres: les conditions d’utilisation, les
conditions ambiantes, une installation adéquate, les modifications sur site, et le niveau de maintenance.
L’effet exact que peut avoir ces facteurs sur la durée de vie des réservoirs d’air est difficilement prévisible.
Si les procédures adéquates de maintenance ne sont pas suivies, la corrosion sur la paroi interne du
réservoir d’air comprimé peut faire que celui-ci éclate de façon inopinée laissant soudainement l’air
pressurisé s’échapper avec force, posant ainsi des risques de dommages corporels à l’utilisateur.
Le réservoir d’air de votre compresseur doit être mis hors service à la fin de l’année mentionnée sur
l’étiquette d’avertissement apposée sur le réservoir.
Les conditions suivantes peuvent amener la dégradation du réservoir d’air, et faire que ce dernier
explose violemment:
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• L’eau condensée n’est pas correctement
vidangée du réservoir d’air provoquant ainsi
la formation de rouille et un amincissement du
réservoir d’air en acier.
• Vidanger le réservoir d’air quotidiennement ou
après chaque utilisation. Si le réservoir présente
une fuite, le remplacer immédiatement par un
nouveau réservoir d’air ou par un nouveau
compresseur.
• Modifications apportées au réservoir d’air ou
tentatives de réparation. • Ne jamais percer un trou dans le réservoir d’air ou ses accessoires, y faire de la soudure ou y
apporter quelque modification que ce soit. Ne
jamais essayer de réparer un réservoir d’air
endommagé ou avec des fuites. Le remplacer
par un nouveau réservoir d’air.
• Des modifications non autorisées de la soupape
de sûreté ou de tous autres composants qui
régissent la pression du réservoir d’air.
• Le réservoir d’air a été conçu pour supporter
des pressions spécifiques de fonctionnement.
Ne faites jamais effectuer de réglages ou de
substitutions de pièces en vue de modifier les
pressions de fonctionnement réglées en usine.
ACCESSOIRES :
• Lorsqu’on excède la pression nominale
des outils pneumatiques, des pistolets
pulvérisateurs, des accessoires à commande
pneumatique, des pneus et d’autres dispositifs
pneumatiques, on risque de les faire exploser
ou de les projeter et ainsi entraîner des
blessures graves.
• Respecter les recommandations du fabricant de
l’équipement et ne jamais dépasser la pression
nominale maximale permise des accessoires.
Ne jamais utiliser le compresseur pour gonfler
de petits objets à basse pression comme des
jouets d’enfant, des ballons de football et de
basket-ball, etc.

18 - FR
PNEUS :
• Des pneus surgonflés pourraient provoquer
des blessures graves et des dommages à la
propriété.
• Utiliser un manomètre pour vérifier la pression
des pneus avant chaque utilisation et lors du
gonflage; consulter le flanc de pneu pour obtenir
la pression correcte.
REMARQUE : Les réservoirs d’air comprimé,
compresseurs et autres équipements similaires
utilisés pour gonfler les pneus peuvent remplir
ces derniers très rapidement.Régler le régulateur
de pression d’air à une pression moindre que
celle indiquée sur le pneu. Ajouter de l’air
par petite quantité et utiliser fréquemment le
manomètre pour empêcher un surgonflage.
DANGER
RISQUE DE CHOC ÉLECTRIQUE
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Votre compresseur d’air est alimenté à
l’électricité. Tout comme n’importe quel autre
dispositif alimenté de façon électrique, s’il n’est
pas utilisé correctement, il peut causer un choc
électrique.
• Ne faites jamais fonctionner le compresseur à
l’extérieur lorsqu’il pleut ou dans des conditions
humides.
• Ne faites jamais fonctionner le compresseur
avec les couvercles de protection enlevés ou
endommagés.
• Les tentatives de réparation par un personnel
non qualifié peuvent résulter en de graves
blessures, voire la mort par électrocution.
• Tout câblage électrique ou toute réparation
nécessaire pour ce produit doit être pris en
charge par un centre de réparation en usine
autorisé conformément aux codes électriques
nationaux et locaux.
• Mise à la terre électrique : Le fait de ne pas
faire une mise à la terre adéquate de ce produit
pourrait résulter en des blessures graves
voire la mort par électrocution. Consulter les
directives relatives à la mise à la terre sous
Installation.
• Assurez-vous que le circuit électrique auquel
le compresseur est branché fournit une mise
à la terre électrique adéquate, une tension
appropriée et une bonne protection des fusibles.
DANGER
RISQUE PROVENANT DES OBJETS PROJETÉS EN L’AIR
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Le flux d’air comprimé peut endommager les
tissus mous de la peau exposée et peut projeter
la poussière, des fragments, des particules
détachées et des petits objets à haute vitesse,
ce qui entraînerait des dommages et des
blessures personnelles.
• Toujours utiliser de l’équipement de sécurité
homologué : protection oculaire conforme à
la norme ANSI Z87.1 (CAN/CSA Z94.3) munie
d’écrans latéraux lors de l’utilisation du
compresseur.
• Ne jamais pointer une buse ou un pulvérisateur
vers une partie du corps ou vers d’autres
personnes ou des animaux.
• Toujours mettre le compresseur hors tension et
purger la pression du tuyau à air et du réservoir
d’air avant d’effectuer l’entretien, de fixer des
outils ou des accessoires.

19 - FR
DANGER
ATTENTION SURFACES CHAUDES
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Toucher à du métal exposé comme la tête du
compresseur ou du moteur, la tubulure des gaz
d’échappement ou de sortie, peut se solder en
de sérieuses brûlures.
• Ne jamais toucher à des pièces métalliques
exposées sur le compresseur pendant ou
immédiatement après son utilisation. Le
compresseur reste chaud pendant plusieurs
minutes après son utilisation.
• Ne pas toucher ni effectuer des réparations aux
coiffes de protection avant que l’appareil n’ait
refroidi.
DANGER
RISQUE ASSOCIÉ AUX PIÈCES MOBILES
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Les pièces mobiles comme une poulie, un
volant ou une courroie peuvent provoquer de
graves blessures si elles entrent en contact
avec vous ou vos vêtements.
• Ne jamais utiliser le compresseur si les
protecteurs ou les couvercles sont endommagés
ou retirés.
• Tenir les cheveux, les vêtements et les gants
hors de portée des pièces en mouvement. Les
vêtements amples, bijoux ou cheveux longs
peuvent s’enchevêtrer dans les pièces mobiles.
• S’éloigner des évents car ces derniers pourraient
camoufler des pièces mobiles.
• Utiliser le compresseur avec des pièces
endommagées ou manquantes ou le réparer
sans coiffes de protection risque de vous
exposer à des pièces mobiles et peut se solder
par de graves blessures.
• Toutes les réparations requises pour ce produit
devraient être effectuées par un centre de
réparation de un centre de réparation autorisé.
DANGER
RISQUE ASSOCIÉ À UTILISATION DANGEREUSE
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Une utilisation dangereuse de votre
compresseur d’air pourrait provoquer de
graves blessures, voire votre décès ou celle
d’autres personnes.
• Revoir et comprendre toutes les directives et les
avertissements contenus dans le présent mode
d’emploi.
• Se familiariser avec le fonctionnement et les
commandes du compresseur d’air.
• Dégager la zone de travail de toutes personnes,
animaux et obstacles.
• Tenir les enfants hors de portée du compresseur
d’air en tout temps.
• Ne pas utiliser le produit en cas de fatigue ou
sous l’emprise d’alcool ou de drogues. Rester
vigilant en tout temps.

20 - FR
• Une utilisation dangereuse de votre
compresseur d’air pourrait provoquer de
graves blessures, voire votre décès ou celle
d’autres personnes.
• Ne jamais rendre inopérant les fonctionnalités
de sécurité du produit.
• Installer un extincteur dans la zone de travail.
• Ne pas utiliser l’appareil lorsqu’il manque des
pièces ou que des pièces sont brisées ou non
autorisées.
• Ne jamais se tenir debout sur le compresseur.
DANGER
RISQUE DE CHUTE
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Un compresseur portatif peut tomber d’une
table, d’un établi ou d’un toit et causer des
dommages au compresseur, ce qui pourrait
résulter en de graves blessures, voire la mort
de l’opérateur.
• Toujours faire fonctionner le compresseur
alors qu’il est dans uns position sécuritaire
et stable afin d’empêcher un mouvement
accidentel de l’appareil. Ne jamais faire
fonctionner le compresseur sur un toit ou
sur toute autre position élevée. Utiliser un
tuyau d’air supplémentaire pour atteindre les
emplacements en hauteur.
DANGER
RISQUE ASSOCIÉ AU BRUIT
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Dans certaines conditions et selon la durée
d’utilisation, le bruit provoqué par ce produit
peut contribuer à une perte auditive.
• Porter systématiquement une protection
auditive appropriée durant l’utilisation.
CONSERVER CES DIRECTIVES
POUR UN USAGE ULTÉRIEUR
SPECIFICATIONS
Modèle no STFP00020
Alésage 30 mm (1,181 po)
Course 14 mm (0,551 po)
Tension monophasée 120/60
Exigence minimale du circuit de dérivation 15 A
Genre de fusibles À retardement
Capacité du réservoir d'air 7,5 litres (2 gallons)
Pression l'amorçage approx. 85 psig
Pression de rupture approx. 115 psig
pi³/min standard (SCFM) à 40 lb/po20,7 *
pi³/min standard (SCFM) à 90 lb/po20,5 *
Pression nominale stabilisée (approximative) 3–115 psig
Type de raccord à connexion rapide 6,4 mm (0,25 po) Industriel
Refiérase al glosario para descifrar las abreviaturas.
*Testé conformément à la norme ISO 1217