Starspace BTX-288 User manual

MODEL:
BTX-288
Congratulations, you are now the owner
of a brand new STARSPACE chair!
Following this assembly guide and you
will nd a quick start guide to assemble
your STARSPACE chair. We highly
recommend checking out our Assembly
Videos as well for even more detailed
and visual instructions.
If you run into any difficulty during the
assembly, remember to check out the
Assembly Video to see if you've missed
anything. If you're unable to resolve your
problems, drop us an email as well and
our support team will assist you.
ASSEMBLY GUIDE
INSTRUCTION MANUAL
Back Cushion *1 Lift *1 Bolts 1/4*7/8” *2
Seat Cushion *1 Lift Cover *1 Bolts 1/4*1” *12
Arms *2 Star Base *1 Plastic Caps *8
Seat Plate *1 Casters *5 Wrench *1
1 5 9
2 6 10
3 7 11
4 8 12
PACKAGE LIST
ASSEMBLY INSTRUCTION
STEP 1: STEP 5:
STEP 6:
STEP 7:
STEP 8:
STEP 2:
STEP 3:
STEP 4:
Contact us if you have
any issues
Mind the important
safety information
Having a friend to help
makes assembly
extra-easy
Scan this QR Code to watch our
assembly video for the chair.
Before you
get started,
a few
pointers:
Step 1: Turn the Star Base(7) upside
down, then press the Casters(8) into
the holes at the end of each base leg,
insert the Lift(5) into the center hole of
the Star Base, the Lift Cover(6) should
be placed over the Lift.
Step 2: Align the Seat Plate(4) over
the pre-drilled holes underneath the
Seat Cushion, make sure that the
front of the seat plate is facing the
front of the Seat Cushion. Attach the
Seat Plate(4) to the Seat Cushion
using TWO Botls 1/4*1”(10) at the
front and TWO Bolts 1/4*7/8”(9) at
the back, tighten all the bolts with the
Wrench(12), being careful not to miss-
thread the bolts or damaged the seat.
Step 3: Attach the Arms(3) to the
Seat Cushion(2) with Four Bolts
1/4*1”(10), using the Wrench(12).
Step 4: Lay the Back Cushion on the
seat of the chair with the top of the
cushion toward the front. Attach the
Back Cushion(1) to the Arms(3) by
inserting Two Bolts 1/4*1”(10) in the
Lower holes with the Wrench(12).
Step 5: Rotate the back of the chair
up, then secure it with the Top Two
Bolts 1/4*1”(10) with the Wrench(12).
Adjust the balance on each side of
the chair, and fully tighten all the bolts
at this step.
Step 6: Align the control handles
of the back adjust over the pre-
drilled holes underneath the Seat
Cushion(2), attach the handle to
the Seat Cushion using Two Bolts
1/4*1”(10), tighten all the bolts with
the Wrench(12).
Step 7: Turn the Seat Cushion
upright and align the center hole of
the Seat Plate(4) over the lift, then
push the Seat Cushion down onto
the lift firmly until the connection is
secure.
Step 8: Press the Plastic Caps(11)
into the Arms holes to cover the bolts.
Note 1: Arm rests are labeled with an "L"
(left) or "R" (right) to show which sides
they should be placed on.
Note 1: Do not tighten all the bolts to
100%, make sure it have space to adjust
in the next steps.
Note 2: Do not tighten all the bolts to
100%, make sure it have space to adjust
in the next steps.
5
7
8
10
1
10
10
10
10
2
3
1
110
9
9
4
1
11
11
Make sure all bolts and screws are
fully tightened before using chair.
Lubricate all moving parts and tighten
all bolts/screws every 6 month or
whenever needed.
CAUTION:
[e-mail]
[phone]
www.starspacechair.com
6
SUBSCRIBE
STARSPACE CHAIR
Watch
video

INSTRUCTIONS FOR USE
1.Seat Height:Paddle-shaped
lever on the right side
3.Operating the tilt lockout
2.Tilt Tension: Long stem under
the seat cushion with knob
4.Adjustable lumbar support
To raise: To increase tension:
To lower: To decrease tension:
While seated, lift lever up. While seated, turn knob
backward (toward - sign).
While taking your weight off
chair, lift lever up.
While seated, turn knob
forward (toward + sign).
At the proper height, your feet should rest
flat on the floor.
Set the tilt tension to control the resistance
you feel when leaning back.
* *
+
_
MODEL:
BTX-288
INSTRUCTION MANUAL
[e-mail] [e-mail]
[phone] [phone]
www.starspacechair.com www.starspacechair.com Scan this QR Code to watch our
assembly video for the chair.
SUBSCRIBE
STARSPACE CHAIR
Watch
video
SAFETY AND MAINTENANCE
SAFETY INFORMATION
LIMITED WARRANTY
STARSPACE promises to repair or replace any STARSPACE chair that is found
to be defective in material or workmanship within one (1) year from the date of
original purchase so long as you, the original purchaser, still owns it. This is your
sole and exclusive remedy. This warranty is subject to the provisions below.
This warranty does not apply and no other warranty applies to:
EXCLUSIONS:
Normal wear and tear, which are to be expected over the course of ownership.
Misuse, abuse or excessive use of the product.
Modications or attachments to the product that are not approved by STARSPACE.
Products that were not installed, used, or maintained in accordance with product
instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
Do not stand on the chair, Do Not use the chair as stepladder.
Use this product for seating one person at a time.
Do not use the chair unless all bolts and screws are rmly secured.
Avoid contact with sharp objects to prevent puncturing the fabric.
Every 6 months, check all bolts and screws to ensure they are tight.
To clean, spot clean only using a damp towel and mild cleaner, rst
test on a small, obscure area of fabric.
Chair weight limit not to exceed 250 lbs.
Sit in the center of
the chair,with your
back to the backrest
Do not push the
chair around when a
person is sitting in it
Do not sit at the
front edge of the
chair
Do not push down
on the backrest
when a person is
reclined
Do not stand on the
chair
Do not place all
your weight on the
backrest only
Do not use the chair
with more than one
person
Seating Usage: Normal use for seating is identied as the equivalent of a single
shift, forty- (40) hour workweek. To the extent that a seating product is used in
a manner exceeding this, the applicable warranty period will be reduced in a
pro-rata manner.
Some retailers might have custom models imported direct from the factory and
therefore are not supported by our local service team because we don’t have
the correct parts, please contact your retailer directly for support. If you have
any questions about that we will be happy to assist and identify those items.
We adopt a 30 days return policy which means that all products purchased on this
website may be returned to us within the timeframe. You need to contact us within
30 days after the product(s) came into your possession and the product(s) must be
returned to us without any undue delays.
RETURN POLICY：
Contact us through the contact form on our website and attach the invoice to the
message as a proof of purchase. And please also write the reason for return.
Returned products must be returned in the same condition as they were sent
and they must be sent in its original packaging.
We will then get back to you as soon as possible with information on where to
send the product(s).
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy
with the product for some other reason), the cost of shipping will fall on
you. And it is your responsibility that the package arrives safely to us so we
recommend that you use a courier service where it is possible to track the
shipment.
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If the product is faulty when you receive it please contact us and we will help
you out.
We reserve the right to give a partial refund in cases when the product(s) is not
in an unused condition, is damaged or have missing parts not due to our error.
HOW RETURNS WORK：
If a refund is approved we will automatically credit the purchase to your credit
card or original method of payment.
The built-in adjustable lumbar
support with controlled lumbar
knob effectively relieves pressure
from the lumbar region.
To stop your chair from tilting,sit
forward,then push the control
handle in.
To let your chair tilt back,pull
the control handle out.