Starspace BTX-293 User manual

INSTRUCT ION MANUAL
MODEL: BTX-293
Before you get started, a few pointers:
Contact us if you have
any issues
Mind the important
safety information
Having a friend to help
makes assembly extra-easy
SUBSCRIBE
STARSPACE CHAIR
Scan this QR Code to
watch our assembly
video for the chair.
CONTACT US
>>> [e-mail]
[phone]
www.starspacechair.com
ASSEMBLY GUIDE
PACKAGE LIST
ASSEMBLY INSTRUCTION
Congratulations, you are now the owner
of a brand new STARSPACE chair!
Following this assembly guide and
you will find a quick start guide to
assemble your STARSPACE chair. We
highly recommend checking out our
Assembly Videos as well for even
more detailed and visual instructions.
If you run into any difficulty during the
assembly, remember to check out the
Assembly Video to see if you've missed
anything. If you're unable to resolve your
problems, drop us an email as well and
our support team will assist you.
[1] [7]
[7]
[13]
[2] [8]
[8]
[14]
[3] [9]
[9]
[15]
[4] [10]
[10]
[16]
[2]
[16]
[5] [11] [17]
[6] [12]
Back Cushion *1 Lift *1 Bolts 5/16*3/4” *3
Seat Cushion *1 Lift Cover *1 Bolts M8*45mm *4
Arms *2 Star Base *1 Plastic Caps *4
Seat Plate *1 Casters *5 Bolts 1/4*7/8” *4
Head Pillow *1 Steel Plate *1 Wrench *1
Back Pillow *1 Bolts M6*25mm *4
STEP 1
STEP 4
STEP 5
STEP 6
STEP 7
STEP 2
STEP 3
Turn the Star Base(9) upside down,
then press the Casters(10) into the
holes at the end of each base leg,
insert the Lift(7) into the center
hole of the Star Base, the Lift
Cover(8) should be placed over the
Lift.
Attach the Steel Plate (11) and
Back Cushion(1) with FOUR
Bolts M6*25mm(12), using the
Wrench(17).
Connect Seat Cushion(2) and
Back Cushion(1), align the Steel
Plate over the pre-drilled holes
with THREE Bolts 5/16*3/4”(13),
tighten all the bolts with the
wrench(17).
Attach the Arms(3) to the Seat
Cushion(2) and Back Cushion(1)
with Four Bolts M8*45mm(14),
using the Wrench(17).
Press the Plastic Caps(15) into the
Arms holes to cover the bolts.
Align the Seat Plate(4) over the
pre-drilled holes underneath the
Seat Cushion, make sure that the
front of the seat plate is facing
the front of the Seat Cushion.
Attach the Seat Plate(4) to the
Seat Cushion(2) using FOUR Botls
1/4*7/8”(16) , tighten all the bolts
with the Wrench(17), being careful
not to miss-thread the bolts or
damaged the seat.
Turn the Seat Cushion upright and
align the center hole of the Seat
Plate(4) over the lift, then push the
Seat Cushion(2) down onto the
lift firmly until the connection is
secure.
[4]
Make sure all bolts and screws are fully tightened before
using chair. Lubricate all moving parts and tighten all bolts/
screws every 6 month or whenever needed.
Arm rests are labeled with
an "L" (left) or "R" (right) to
show which sides they should
be placed on.
CAUTION
NOTE
[12]
[13]
[14]
[15]
[15]
[14]
[3]
[1]
[11]

SUBSCRIBE
STARSPACE CHAIR Scan this QR Code to
watch our assembly
video for the chair.
CONTACT US
>>> [e-mail]
[phone]
www.starspacechair.com
1
2
Seat Height:Paddle-
shaped lever on the right
side
Tilt Tension: Long stem
under the seat cushion
with knob
INSTRUCT ION MANUAL
MODEL: BTX-293
INSTRUCTIONS FOR USE SAFETY AND MAINTENANCE
SAFETY INFORMATION
LIMITED WARRANTY
Sit in the center of
the chair,with your
back to the backrest
Do not push the
chair around when a
person is sitting in it
Do not sit at the
front edge of the
chair
Do not push down on
the backrest when a
person is reclined
Do not stand on the
chair
Do not place all
your weight on the
backrest only
Do not use the chair
with more than one
person
While taking your weight
o chair, lift lever up.
While seated, turn
knob forward (toward
+ sign).
While seated, lift lever
up.
While seated, turn knob
backward (toward -
sign).
At the proper height, your feet should rest at on the oor.
Set the tilt tension to control the resistance you feel when leaning back.
+
_
>>> To increase tension
>>> To increase tension
>>> To increase tension
>>> To increase tension
Do not stand on the chair, Do Not use the chair as stepladder.
Use this product for seating one person at a time.
Do not use the chair unless all bolts and screws are rmly secured.
Avoid contact with sharp objects to prevent puncturing the fabric.
Every 6 months, check all bolts and screws to ensure they are tight.
To clean, spot clean only using a damp towel and mild cleaner,
rst test on a small, obscure area of fabric.
Chair weight limit not to exceed 350 lbs.
STARSPACE promises to repair or replace any STARSPACE chair
that is found to be defective in material or workmanship within one (1)
year from the date of original purchase so long as you, the original
purchaser, still owns it. This is your sole and exclusive remedy. This
warranty is subject to the provisions below.
This warranty does not apply and no other warranty applies to:
EXCLUSIONS:
Normal wear and tear, which are to be expected over the course of
ownership.
Misuse, abuse or excessive use of the product.
Modications or attachments to the product that are not approved
by STARSPACE.
Products that were not installed, used, or maintained in accordance with
product instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
Seating Usage: Normal use for seating is identied as the equivalent of
a single shift, forty- (40) hour workweek. To the extent that a seating
product is used in a manner exceeding this, the applicable warranty
period will be reduced in a pro-rata manner.
Some retailers might have custom models imported direct from the
factory and therefore are not supported by our local service team
because we don’t have the correct parts, please contact your retailer
directly for support. If you have any questions about that we will be
happy to assist and identify those items.
We adopt a 30 days return policy which means that all products
purchased on this website may be returned to us within the timeframe.
You need to contact us within 30 days after the product(s) came into your
possession and the product(s) must be returned to us without any undue
delays.
RETURN POLICY：
Contact us through the contact form on our website and attach the
invoice to the message as a proof of purchase. And please also write
the reason for return.
Returned products must be returned in the same condition as they
were sent and they must be sent in its original packaging.
We will then get back to you as soon as possible with information
on where to send the product(s).
If the product is not faulty, (i.e. if you changed your mind or if you are
unhappy with the product for some other reason), the cost of shipping
will fall on you. And it is your responsibility that the package arrives
safely to us so we recommend that you use a courier service where it
is possible to track the shipment.
As soon as we have received the product(s) and made an
inspection we will inform you of our decision.
If the product is faulty when you receive it please contact us and we
will help you out.
We reserve the right to give a partial refund in cases when the
product(s) is not in an unused condition, is damaged or have
missing parts not due to our error.
HOW RETURNS WORK：
If a refund is approved we will automatically credit the purchase to
your credit card or original method of payment.
Before you get started, a few pointers:
Contact us if you have
any issues
Mind the important
safety information
Having a friend to help
makes assembly extra-easy