Southern Enterprises MS040500TX User manual

Page |
1
PO#:
MS040500TX
Fortenbury Media Console
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.sei
furniturestore
.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 1
Upper Shelf Panel
5) Quantity
of 2
Middle Panel
6)Quantity
of 2
Front Vertical Panel
7) Quantity
of 2
Back Vertical Panel
8) Quantity
of 1
Lower Shelf Panel
9) Quantity
of 1
Bottom Panel
10) Quantity
of 2
Small Drawer Front Panel
11) Quantity
of 3
Drawer Left Side Panel
12) Quantity
of 3
Drawer Right Side Panel
Fortenbury Media Console
Parts List
Please check packaging for all parts and hardware before discarding. Before beginning assembly, separate each
type of hardware. Carefully study the diagrams below and check that you have all parts indicated.
Call Customer Service if missing any hardware. Using the incorrect hardware will cause damage.

Page |
3
13) Quantity
of 2
Small Drawer Back Panel
14) Quantity
of 2
Small Drawer Bottom Panel
15) Quantity
of 1
Big Drawer Front Panel
16) Quantity
of 1
Big Drawer Back Panel
17) Quantity
of 1
Big Drawer Bottom Panel
18) Quantity
of 1
Back Panel
A) Quantity
of 26
Cam Bolts
B) Quantity
of 26
Cam Locks
C) Quantity
of 32
Wood Dowels Dia. 5/16"x1-1/4"
D)Quantity
o f 6
Bolt Dia. 1/4x1-1/2” L
E)Quantity
o f 6
Spring Washer Dia.1/4”
F)Quantity
o f 6
Flat washer Dia.1/4” x3/4”
G) Quantity
of 1
Allen Wrench
H
) Quantity
of 18
Screw Dia. 1/8” x 1/2”L
I) Quantity
of 12
Cam Bolts

Page |
4
J) Quantity
of 12
Cam Locks
K) Quantity
of 3
Knob
L) Quantity
of 3
Bolts
Dia. 5/32”x 3/4”L
M) Quantity
of 16
Screw
Dia. 5/32”x 1L
N) Quantity
of 12
Cotton Mat
O) Quantity
of 2
Anti-tipping hardware
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
SEI Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
5
Figure 1
Attach Upper shelf Panel (4) to Middle
Panels (5) with Screws (M) and Wood
Dowels (C).
Tighten Screws (M) with Phillips
screwdriver (not included).
Please do not overtighten cam locks. Stop when they feel
secure.
Figure 2
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from Figure
1.
Screw Cam Bolts (A) into threaded holes
on Back Vertical Panel (7).
Attach Back Vertical Panel (7) to
pre-assembled unit from Figure 1 by
inserting Cam Bolts (A) into corresponding
holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
Fortenbury Media Console
Assembly Instructions
4

Page |
6
Figure 3
Attach Lower Shelf Panel (8) to Back
Vertical Panel (7) by using Wood Dowels
(C) as shown in Figure 3.
Figure 4
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from Figure
3.
Screw Cam Bolts (A) into threaded holes
on Front Vertical Panel (6).
Attach Front Vertical Panel (6) to
pre-assembled unit from Figure 3 by
inserting Cam Bolts (A) into corresponding
holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
8

Page |
7
Figure 5
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from Figure
4.
Screw Cam Bolts (A) into threaded holes
on Side Panels (2/3).
Attach Side Panels (2/3) to pre-assembled
unit from Figure 4 by inserting Cam Bolts
(A) into corresponding holes until all
panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
Figure 6
Insert Cam Locks (B) into corresponding
holes on Back Vertical Panel (7).
Screw Cam Bolts (A) into threaded holes
on Bottom Panel (9).
Attach Bottom Panel (9) to pre-assembled
unit from Figure 5 by inserting Cam Bolts
(A), Bolt (D), Spring Washers (E), Flat
Washers (F), and Wood Dowels (C) into
corresponding holes until all panels meet.
Tighten bolts with Allen Wrench (G).
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
C
C

Page |
8
Figure 7
Insert Cam Locks (B) into corresponding
holes on pre-assembled unit from Figure
6.
Screw Cam Bolts (A) into threaded holes
on Top Panel (1).
Attach Top Panel (1) to Side Panels (2/3)
and Middle Panel (5) by inserting Cam
Bolts (A) and Wood Dowels (C) into
corresponding holes until all panels meet.
Tighten Cam Bolts (A) by rotating Cam
Locks (B) clockwise using Phillips
screwdriver (not included).
Figure 8
Attach Back Panels (18) to back of the unit
with Screws (H).
Tighten Screws (H) with Phillips
screwdriver (not included) .
A
B
C
H
18

Page |
9
Figure 9
Insert Cam Locks (J) into corresponding
holes on Drawer Side Panels (11/12).
Screw Cam Bolts (I) into threaded holes
on Drawer front (10).
Attach Drawer Front (10) to Drawer Side
Panels (11/12) by inserting Cam Bolts (I)
into corresponding holes until all panels
meet.
Tighten Cam Bolts (I) by rotating Cam
Locks (J) clockwise using Phillips
screwdriver (not included).
Cover Cam Locks (J) with Covers (N)
Insert Drawer Bottom Panel (14) into
grooves of Drawer Panels (10/11/12).
Attach Drawer Back Panel (13) to
assembled unit using Screws (M).
Attach Knobs (K) to Drawer Front Panel
(10) using Bolts (L).
Tighten Bolts and Screws with Phillips
screwdriver (not included).
J

Page |
10
Figure 10
Insert Cam Locks (J) into corresponding
holes on Drawer Side Panels (11/12).
Screw Cam Bolts (I) into threaded holes
on Drawer front (15).
Attach Drawer Front (15) to Drawer Side
Panels (11/12) by inserting Cam Bolts (I)
into corresponding holes until all panels
meet.
Tighten Cam Bolts (I) by rotating Cam
Locks (J) clockwise using Phillips
screwdriver (not included).
Cover Cam Locks (J) with Covers (N).
Insert Drawer Bottom Panel (17) into
grooves of Drawer Panels (11/12/15).
Attach Drawer Back Panel (17) to
assembled unit using Screws (M)
Attach Drawer Side Panels (11/12) to
Drawer Back Panel (16) using Screws (M).
Attach Knobs (K) to Drawer Front Panel
(15) using Bolts (L).
Tighten Bolts and Screws with Phillips
screwdriver (not included).