StarTech.com USB32HD4 User manual

Quick-Start Guide
Product Diagram (USB32HD4 & USBC2HD4)
Component Function
1(USB32HD4) USB-A
Host Connector
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• (USB32HD4) Connect to a USB-A Enabled Host
Computer
2(USBC2HD4) USB-C
Host Connector
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• (USBC2HD4) Connect to a USB-C Enabled Host
Computer
3HDMI Ports x 4 • Connect up to 4 HDMI Enabled Display Devices
Product Information
“For the latest product information, technical specications, manuals, and Declarations
of Conformance please visit: www.StarTech.com/USB32HD4 or www.StarTech.com/
USBC2HD4”
Package Contents
USB32HD4
• USB-A to HDMI Adapter x 1
• Quick-Start Guide x 1
USB to 4 X HDMI Display Adapter
USBC2HD4
• USB-C to HDMI Adapter x 1
• Quick-Start Guide x 1
Driver Installation
Installation is automatic for Windows 10 in most situations. If the drivers do not auto-
install, contact your IT administrator or department to allow the driver installation. Visit
www.startech.com/USB32HD4 or www.startech.com/USBC2HD4 to locate the latest
drivers.
Note: This USB video adapter uses a Trigger family chipset. If you’re connecting this
device to a computer along with additional USB video adapters or docking stations,
avoid using devices with dierent family chipsets, such as DisplayLink® or Fresco Logic
Note: ®Operating system requirements are subject to change. For the latest
requirements, please visit www.StarTech.com/USB32HD4 or www.StarTech.com/
USBC2HD4
Installation
Connect a Host
USB32HD4
• Connect the USB-A Host Connector of the USB-A to HDMI Adapter to a USB-A
Port on a USB-A Enabled Host Computer.
USBC2HD4
• Connect the USB-C Host Connector of the USB-C to HDMI Adapter to a USB-C
Port on a USB-C Enabled Host Computer.
Connect the Display Devices
• Connect an HDMI Enabled Display Device to the HDMI Port of the USB to 4 X
HDMI Display Adapter using an HDMI Cable.
• (Optional) Repeat to connect up to 4 x extended or mirrored HDMI Enabled
Display Devices.
Arrange Display Devices
• Arrange connected Display Devices using Windows Display Settings on the Host
Computer.
3*product may vary from photos
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: May 7, 2021 11:30 AM
21

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety
hazards.
Mesures de sécurité
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et acheminés de façon à éviter tout
risque électrique, de chute ou de sécurité
安全対策•ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するようにしてください。Misure di sicurezza
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da evitare pericoli di inciampo,
rischi di scosse elettriche o pericoli per la sicurezza.
Säkerhetsåtgärder
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra
olyckor kan undvikas.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands