StarTech.com PCI2S1P2 User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: March 10, 2021
Product Diagram (PCI2S1P2)
Front View
Port Function
1Parallel Connector • Connect to the Parallel Pins on the PCI Card
2Low-Prole Bracket
(Parallel) • See Installing the Low-Prole Bracket(s)
3Parallel Port • Connect a Parallel Peripheral Device
• DB-25 Parallel (Female)
4Low-Prole Brackets
(Serial) • See Installing the Low-Prole Bracket(s)
5Serial Ports • Connect Serial Peripheral Devices
• DB-9 Parallel (Male)
6PCI Connector • Connect the PCI Card to the PCI Slot in the
Computer
Package Contents
• PCI Serial Parallel Combo Card x 1
• Full-Prole Bracket (Installed) x 1
• Low-Prole Brackets (for Serial Ports) x 2
• Low-Prole Bracket (for Parallel Port) x 1
• Quick-Start Guide x 1
2S1P PCI Serial Parallel Combo Card with 16C550 UART
Requirements
For the latest requirements, please visit:
www.startech.com/PCI2S1P2.
• Computer with an available PCI slot (x4/8/16)
• Needle-nose Pliers or 3/16 Nut Driver
Hardware Installation
Warning: PCI Cards can be damaged by static electricity. Make sure that the
Installer is properly grounded before they open the Computer Case or touch the PCI
Card. The Installer should wear an Anti-Static Strap when installing any computer
component. If an Anti-Static Strap is not available, discharge any built-up static
electricity by touching a large Grounded Metal Surface for several seconds. Only
handle the PCI Card by its edges and do not touch the gold connectors.
Installing the Low-Prole Bracket(s)
By default the Full-Prole Bracket is attached to the Serial/Parallel Port(s).
Depending on the system conguration it may be necessary to remove the Full-
Prole Bracket(s) to replace with the Low-Prole Bracket(s) (included).
1. Remove the Hexagonal Standos from both sides of each Port, using a 3/16 Nut
Driver or a pair of Needle-nose Pliers.
2. Remove the Full-Prole Bracket(s) and replace with the Low-Prole Bracket(s).
3. Install the Hexagonal Standos removed in step 1. Thread the Hexagonal
Standos onto each Threaded Post and tighten, using a 3/16 Nut Driver or a pair
of Needle-nose Pliers.
Installing the Card
1. Turn o the Computer and any Peripheral Devices that are connected
(e.g. printers, external hard drives, etc.).
2. Unplug the Power Cable from the rear of the Computer and disconnect any
Peripheral Devices that are connected.
3. Remove the Cover from the Computer Case.
Note: Consult the documentation that came with the Computer for details about
how to do this safely.
4. Locate an open PCI Slot and remove the corresponding Metal Cover Plate from the
rear of the Computer Case. In most instances, the Metal Cover Plate is attached
to the rear of the Computer Case with a single Screw. Save this Screw for the next
step.
6
3
2
5
4
1

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Software Installation
Driver Installation
This product requires a driver to be installed on the Host Computer. Download the
latest Drivers from the StarTech.com website:
www.startech.com/PCI2S1P2.
Navigate to the Drivers/Downloads tab to locate the Drivers. Follow the instructions
included with the Driver Files.
5. Gently insert the PCI Card into the open PCI Slot and fasten the Bracket to the rear
of the Computer Case, using the Screw from step 4.
6. Locate a second open PCI Slot and remove the corresponding Metal Cover Plate
from the rear of the Computer Case. In most instances, the Metal Cover Plate is
attached to the rear of the Computer Case with a single Screw. Save this Screw for
the next step.
7. Fasten the Bracket (Parallel) to the rear of the Computer Case, using the Screw
from step 6.
8. Place the Cover back onto the Computer Case.
9. Reconnect all of the Peripheral Devices that were disconnected in step 2.
10. Connect a Serial Device to the Serial Port on the PCI Card.
11. Connect a SPP/EPP/ECP Peripheral Device to the Parallel Port on the PCI Card.
12. Reconnect the Power Cable to the rear of the Computer.