Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or
symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are
for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or
an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.
com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names
and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a lifetime warranty. For further information on product warranty terms and conditions,
please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors,
employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product
exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental
or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not
apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Safety Measures
• Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product.
Mesures de sécurité
• Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant de commencer à assembler et utiliser
ce produit.
安全対策
• 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解してから組み立て作業を始めて下さい。
Misure di sicurezza
• Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare
questo prodotto.
Säkerhetsåtgärder
• Läs hela manualen och se till att du förstår instruktionerna innan du börjar montera och använda produkten.
9. Use a Phillips Head Screwdriver to install the M6x12mm Screws and fasten the
Front Mounting Brackets to the Front Mounting Posts of the rack. Ensure the M6
Screws are properly tightened.
10. Repeat Step 8 for the Rear Mounting Brackets.
11. (Optional) Make minor depth adjustments to the Front and Rear Mounting
Brackets as needed.
Installation
1. Locate a suitable location in the rack or cabinet to mount the Shelf. The Shelf
requires 1U of Space.
To mount the shelf leveled, ensure the mounting brackets are mounted on the same U
height number. To determine this, most four posts racks or cabinets have labeled front
and rear posts.
2. Determine the Depth of the Mounting Posts on the rack. The Adjustable Mounting
Depth of the Shelf is from 19.5 in (495 mm) to 38.3in (974 mm).
3. Use a Phillips Head Screwdriver to Loosen the Panel Screws of the Front and Rear
Mounting Brackets so they can slide freely. Each Mounting Bracket uses Two Panel
Screws.
4. (Optional) Remove all the Panel Screws (x 8) of the Front and Rear Mounting
Brackets if the adjustment requires dierent Depth Adjustment Holes on the sides
of the Shelf.
5. Adjust the Front and Rear Mounting Brackets to achieve the same Mounting
Depth as the Mounting Posts of the rack. Next, secure the Panel Screws (x 8) of the
Front and Rear Mounting Brackets with a Phillips Head Screwdriver.
6. (Optional) Install the M6 Cage Nuts (x 8) into the appropriate Cage Nut Holes (x 8)
on the chosen U Height Number on the Mounting Posts of the rack.
Use a cage nut tool if available or your preferred installation method to install the
M6 Cage Nuts.
7. Place the M6 Plastic Washers (x 8) onto the M6x12mm Screws (x 8).
8. Place the Shelf into the rack in the chosen U Height Number. Align the Mounting
Holes of the Front Mounting Posts of the rack with the Front Mounting Brackets.
Keep supporting the weight of the shelf.
