StarTech.com BT52A User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 10, 2021 5:47 PM
Product Diagram (BT52A)
Component Function
1DC 5V Port (micro
USB)
• Used to connect the Power Adapter to the
Audio Receiver.
2Optical Port • Used to connect an Audio Device via Toslink®
Cable to the Audio Receiver.
3Audio Out Port • Used to connect an Audio Device via 3.5 mm
Cable to the Audio Receiver.
4 LED Indicator (front)
• Flash Once: Indicates that the Audio Device is
powered and waiting to pair with a Bluetooth
Device.
• Solid: Indicates that a Bluetooth Device has
been paired with the Audio Receiver.
• Blinking: Indicates that the Bluetooth Device
is disconnected from the Audio Receiver.
Requirements
For the latest requirements, please visit www.startech.com/BT52A
Powering the Audio Receiver
1. Connect the Universal Power Adapter to the DC 5V Port on the Audio Receiver and
the other end to an AC Electrical Outlet.
2. The LED Indicator will ash once, Indicating that the Audio Device is powered and
waiting to pair with a Bluetooth Device.
Bluetooth® 5.0 Audio Receiver
Connecting the Audio Receiver
Analog
• Connect the 3.5 mm Audio Cable (included) to the Audio Out Port on the Audio
Receiver and the other end to an Audio In Port on the Audio Device (audio
receiver, etc.)
- or -
Connect the 3.5 mm Audio Cable (included) to the Audio Out Port on the Audio
Receiver and the other end to the RCA Breakout Cable (included). Then connect
both the left and right connectors on the RCA Breakout Cable to the left and right
Audio In Ports on the Audio Device.
Digital
• Connect the Toslink Cable (sold separately) to the Optical Port on the Audio
Receiver and the other end to an Optical Port on the Audio Device (audio receiver,
etc.)
Pairing with NFC Fast Connection
The Audio Receiver is equipped with a standard NFC tag to allow for NFC pairing.
NFC allows you to connect a Bluetooth Device to the Audio Device by touching the
Bluetooth Device to the Audio Receiver.
The maximum distance the Bluetooth Device can be from the Audio Receiver is 66 ft
(20 meters).
NOTE: Store the connection data for up to eight Bluetooth Devices. Connect and
use one Bluetooth Device at a time.
1. Ensure NFC is enabled on your Bluetooth Device. Check the device’s manual for
details.
2. Touch a Bluetooth Device to the top of the Audio Receiver for 3 seconds.
NOTE: If this is the rst time your Bluetooth Device has been paired you may receive
a message requesting access.
3. The Bluetooth Device is now paired, the LED Indicator will be solid and audio
from the Bluetooth Device will output through the connected Audio Device.
Disconnecting from your NFC Device
1. Touch the paired Bluetooth Device to the top of the Audio Receiver for 3 seconds.
2. The Bluetooth Device is now disconnected from the Audio Device.
123
4

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
ISED Statement
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0.5cm between the radiator and your body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm
Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International,
Ltd., registered in the United States and other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Manually Pairing a Device
Note: If the instructions below do not match your Device, please refer to the owners
manual for your Device for further instructions.
1. From the Host Bluetooth Device, select Settings.
2. On the Settings screen, select Bluetooth.
3. Select the Sider to activate the Bluetooth function.
4. A list of enabled Bluetooth Devices will appear. Select the HD Receiver from the
list.
Reconnecting a Device
1. Move the Bluetooth Device back into the expectable range of the Audio Receiver
(66 ft or 20 meters).
2. Go back into the Bluetooth Device’s Bluetooth Settings and select the HD
Receiver from the list.