StarTech.com NETRS232485W User manual

Manual Revision: 02/24/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
NETRS232485W
1 Port Industrial RS232/422/485 Wireless/
Wired Serial Device Server
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
FCC ID: FCC ID: WHD-DS-11-WG
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une
distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à
leur proximité.
IC: 11232A-NETRS232485W

Instruction Manual
3
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Side 1 ............................................................................................................................................................. 1
Side 2 ............................................................................................................................................................. 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
DB-9 Connector Pinout .........................................................................3
DIP Switch Conguration......................................................................3
Installation ..............................................................................................4
Hardware Installation .............................................................................................................................. 4
Software Installation................................................................................................................................ 4
Operation ................................................................................................5
Specications..........................................................................................7
Technical Support ..................................................................................8
Warranty Information............................................................................8

Instruction Manual
1
Product Diagram
Front View
1. LED for PWR1
2. LED for PWR2
3. LED for Ethernet Port 1
4. LED for Wireless LAN
5. LED for Serial Port
Side 1
1. Terminal Block PWR1 (12~48V DC)
2. Power Jack PWR2 (12~48V DC)
3. Port RJ45 10/100
4. Reverse SMA Connector for the
Antenna
Side 2
1. Reset Button
2. DB-9 Serial Port
3. DIP Switch

Instruction Manual
2
Introduction
Packaging Contents
• 1x Serial over IP Device Server
• 1x2dBi Antenna
• 1x DIN-Rail Kit
• 1x Wall-Mount Kit
• 1x Software CD
• 1x Installation Guide
System Requirements
• System Requirements
• Windows® 8 (32/64bit), 7 (32/64), Vista(32/64), XP(32/64), 2000, Windows® Server
2008 R2, 2003(32/64).

Instruction Manual
3
DB-9 Connector Pinout
DIP Switch Conguration
DIP 1 DIP 2 Termination Conguration
ON ON Termination for long distance 4-wire RS485/422
ON OFF Reserved
OFF ON Termination for long distance 2-wire RS485
OFF OFF No termination for RS485/ 422 (short distance)

Instruction Manual
4
Installation
Hardware Installation
The server can be installed on a DIN rail or it can be wall-mounted.
Installation on a DIN-Rail:
1. Tilt the unit, making sure that the metal spring located at the back is positioned on
top of the DIN rail.
2. Push the unit towards the rail until a “click” sound is heard.
Installation on a Wall:
1. Remove the DIN-rail kit, if it is installed on the unit.
2. Install the wall-mount panel included using the 3 screws found in the package.
3. Mount the unit on the wall using the appropriate hardware for the surface you are
mounting to.
Software Installation
1. Insert the provided CD into your DVD/CD-ROM drive.
2. Browse to the folder “fscommand\Utility\DS-Tool” and execute the installer
“Startech_V1.0_xxxxxxx”
3. Follow the on-screen instructions to complete the installation.

Instruction Manual
5
Operation
For full operation instructions, please visit www.startech.com/NETRS232485W
1. Start the DS-Tool, allow the install of the driver
2. Allow access to the DS-Tool on the Windows Firewall
3. Once the utility opens, click the “Broadcast” button to detect the device server. The
default IP address of the device is “192.168.10.2”.
4. Once detected, click the checkbox beside the device you would like to congure,
and then click the “Add” button to congure your desired IP settings (Static/DHCP).

Instruction Manual
6
To add a virtual COM port, please use the VCOM Wizard and follow the steps.

Instruction Manual
7
Specications
Interface Serial
Ports 1
Supported Protocols ICMP, IP, TCP, UDP, DHCP, BOOTP, ARP/RARP,
DNS, SNMP MIB II, HTTPS, SSH
Connectors
1x DB-9 male,
1x RJ-45
1x Reverse SMA Connector
1x DC Power
1x 3pin Terminal Block
LED Indicator(s) 1x Ethernet Link, PWR1,PWR2, Wireless
LAN, Serial
Supported Serial Protocols RS232/422/485
Ethernet Link Speed 10/100 Mbps
Wireless LAN Standards IEEE802.11b/IEEE802.11g
Maximum Baud Rate 230.4 Kbps
Power Input
Terminal Block: 12 ~ 48VDC in 3-pin
12 ~ 48VDC, center positive, power jack
plug
Enclosure Material Metal
Operating Temperature -10 to 65°C (14 to 149°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Humidity 5% to 95% Non-condensing
Dimensions 124mm x 73mm x 30mm
Weight 346 g
Compatible Operating Systems
Windows® 8 (32/64bit), 7 (32/64),
Vista(32/64), XP(32/64),Windows® Server
2012, 2008 R2, 2003(32/64)

Instruction Manual
8
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.