StarTech.com PM1115UW User manual

Manual Revision: 11/09/2021
User Manual
For the latest information and specications visit
www.startech.com/PM1115UW
Wireless N USB 2.0 Network Print Server
SKUs: PM1115UW, PM1115UWEU
Actual product may vary from photos

i
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
CAN ICES-3 (B)/NMB-3(B)
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.

ii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Déclaration d’exposition à la radiation
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies
pour un environnement non contrôlé. Cet équipement doit être installé et mis
en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de
votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni
se trouver à leur proximité.
FCC ID: 2AA3I-PM1115UWB
IC: 11232A-PM1115UWB
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

iii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
電源が入っている状態の製品または電線の終端処理を行わないでください。
ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを
行い、電気障害やつまづきの危険性など、安全上のリスクを回避するように
してください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

iv
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
• Read the entire manual and ensure the instructions are fully understood
before assembling and/or using this product.
• This product is intended for indoor use only and should not be used
outdoors.
Varningsmeddelanden
• Läs hela manualen och se till att du förstår instruktionerna innan du börjar
montera och använda produkten.
• Produkten är endast avsedd för användning inomhus och ska inte användas
utomhus.
Waarschuwingen
• Lees de gehele handleiding en zorg dat u de instructies begrijpt voordat u dit
product in elkaar zet en gebruikt.
• Dit product is alleen bedoeld voor binnengebruik en mag niet buiten
worden gebruikt.
注意
• 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解して
から組み立て作業を始めて下さい。
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。
Dichiarazioni di avvertenza
• Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni
prima di iniziare ad assemblare e a utilizzare questo prodotto.
• Il prodotto è destinato all’uso in ambienti interni. Se ne sconsiglia l’impiego
in ambienti esterni.
Avertissements
• Lisez tout le manuel et assurez-vous que vous comprenez les instructions
avant de commencer à assembler et utiliser ce produit.
• Ce produit est uniquement destiné à une utilisation en intérieur et ne doit
pas être utilisé à l’extérieur.

v
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Mensagens de aviso
• Leia todo o manual e certique-se de que entende as instruções antes de
começar a montar e a utilizar este produto.
• Este produto destina-se apenas a uma utilização no interior e não deve ser
utilizado no exterior.
Advertencias de uso
• Lea todo el manual y asegúrese de haber comprendido bien las instrucciones
antes de proceder con el ensamblaje y el uso de este producto.
• El uso de este producto es solo para interiores y no debe utilizarse en
exteriores.
Warnhinweise
• Bevor Sie dieses Produkt montieren und verwenden, lesen Sie das gesamte
Handbuch und vergewissern Sie sich, dass Sie die Anweisungen verstanden
haben.
• Dieses Produkt ist nur zum Gebrauch in Innenräumen vorgesehen und sollte
nicht im Freien verwendet werden.

Table of Contents
Compliance Statements........................................................................i
Safety Statements..................................................................................iii
Warning Statements ..............................................................................iv
Product Diagram ....................................................................................1
Front View.................................................................................................................................................... 1
Back View ..................................................................................................................................................... 1
Product Information ..............................................................................2
Requirements ............................................................................................................................................. 2
Package Contents ..................................................................................................................................... 2
Congurations............................................................................................................................................ 2
Installation ..............................................................................................3
Default Settings......................................................................................................................................... 3
Basic Hardware Installation................................................................................................................... 3
Hardware and Software Installation................................................................................................... 3
Operation ................................................................................................20
LED Indicators............................................................................................................................................. 20
Reset Button................................................................................................................................................ 20
Troubleshooting ....................................................................................................................................... 22
Warranty Information............................................................................25
Limitation of Liability ............................................................................25
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Front View
Back View
1WAN LED 5LED Indicators
2WPS Button 6USB-A Port
3Reset Button 7RJ45 Port
4DC Jack
2
3
1
4
5 6 7

2
Product Information
Requirements
For the latest product software, product information, technical
specications, manuals, and Declarations of Conformance,
please visit:
www.startech.com/PM1115UW
www.startech.com/PM1115UWEU
Note: The Print Server does not support printing with Host-
Based Printers (e.g. CAPT, GDI, PPA).
Package Contents
• Wireless Print Server x 1
• Power Adapter x 1
• Product Insert x 1
Congurations
Operating
System
Function
PS Admin Utility /
Setup Wizard
Windows® XP,
Vista, 7, 8, 8.1, 10
Install a single
print server on a
network
Embedded Web
server
Windows, macOS,
and Linux
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/supportTo view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installation
Default Settings
• Username: admin
• Password: (None)
• Wireless Mode: Ad-Hoc (Peer-to-Peer)
• SSID: PM1115UW
• IP Address: 192.168.0.10
Basic Hardware Installation
1. Turn OFF the Power to the Printer.
2. Connect the Print Server to the Printer, using an appropriate
USB Printer Cable.
3. Turn ON the Power to the Printer.
4. Connect the Power Adapter to the DC Jack, located on the
back of the Print Server.
5. Wait ~40 seconds for the Print Server’s Power On Self Test
(POST) to complete.
6. (Optional) Connect an RJ45 Network Cable to the Print
Server and to a Network Device (e.g. network switch or wall
jack).
Hardware and Software Installation
The PM1115UW can be installed using two distinct methods.
Method 1: For a streamlined installation, follow the steps
listed in the Basic Software Installation section. Please note
that this method is only available in Windows.