Stealth Products GAT444-IP User manual

USER MANUAL
Upper Extremities
GAT444-IP
Stealth’s User Manual And Maintenance Guide
for the Gatlin Swivel Tablet Mount

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer satisfaction. Your complete
satisfaction is important. Please contact us with feedback or suggested
changes that will help improve the quality and usability of our products.
You may reach us at:
General
Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse due to failure of the following
instructions will void the warranty.
Immediately discontinue use if any function is compromised, parts are missing,
loose, or shows signs of excessive wear. Consult with your supplier for repair,
adjustment, or replacement.
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1(800) 965-9229
Fax: [phone] Toll Free: 1(800) 806-1225
[email protected] www.stealthproducts.com

ii
Important Information 2.0
Important Information!
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in these instructions must be familiar with and understand all safety
aspects of the devices mentioned. In order for our products to be used
successfully, you must:
 Read and understand all instrucons and warnings.
 Maintain our products according to our instrucon on care and maintenance.
 Devices should be installed and adjusted by a trained technician.
Supplier Reference
Supplier:
Telephone:
Address:
Purchase Date:
Model:

iii
Introduction 3.0
Before you install or begin using this product, it is important that you read and
understand the content of these installation and operating instructions. The
installation instructions will guide you through the possibilities with the
Gatlin Swivel Mount.
Instructions are written with the expressed intent of use with standard
configurations. They also contain important safety and maintenance
information. For further assistance, or more advanced applications, please
contact your supplier or Stealth Products at [phone] or toll free at
1-800-965-9229.
Always keep the operating instructions in a safe place so they may be
referenced as necessary.
All information, pictures, illustrations, and specifications are based on the
product information that was available at the time of printing. Pictures and
illustrations shown in these instructions are representative examples and are
not intended to be exact depictions of the various parts of the product.
Ordering Documentation
You can download additional copies of this User Manual on the Stealth website:
https://stlpro.site/stealth-docs
and search: GAT444-IP User Manual in the search bar at the top of the page.

iv
Warranty 4.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon or product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally
void this warranty.
Stealth Products, LLC is liable for replacement parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials
or workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at [phone] or toll free [phone].
2. Request the Returns Department or obtain an RA from the Returns Department and
follow department or documentaon instrucons.

v
Table of Contents 5.0
1.0 Customer Satisfaction ............................................................................ i
2.0 Important Information.......................................................................... ii
3.0 Introduction........................................................................................... iii
4.0 Warranty ................................................................................................ iv
5.0 Table of Contents.................................................................................... v
6.0 Warning Labels...................................................................................... vi
6.1 Warning Labels ................................................................................................... vi
6.2 Limited Liability................................................................................................... vi
6.3 Testing.................................................................................................................... vi
7.0 Parts And Accessories ......................................................................... vii
7.1 Parts Included ..................................................................................................... vii
8.0 Mounting ............................................................................................... 1
8.1 Intended Use ......................................................................................................... 1
8.2 GAT400-IP Swivel Mount.................................................................................. 1
8.3 Hardware Mounting ........................................................................................... 2
8.4 Armrest Mounting............................................................................................... 3
9.0 Positioning.............................................................................................. 4
9.1 Gatlin Positioning ................................................................................................ 4
10.0 Adjustments ......................................................................................... 5
10.1 GAT444-IP Adjustment ................................................................................... 5
10.2 Gatlin Adjustment ............................................................................................. 6
11.0 First Time Use....................................................................................... 7
11.1 Dealer Assistance .............................................................................................. 7
11.2 User Testing......................................................................................................... 7
11.3 Conditions Of Use............................................................................................. 7
12.0 Maintenance ......................................................................................... 8
12.1 Care And Maintenance ................................................................................... 8

vi
Warning Labels 6.0
Warning Labels 6.1
Warnings are included for the safety of the user, client, operator and property.
Please read and understand what the signal words SAFETY, NOTICE, CAUTION,
WARNING and DANGER mean, how they could affect the user, those around
the user, and property.
Limited Liability 6.2
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to follow
the recommendations, warnings, and instructions in this manual.
Testing 6.3
Initial setup and driving should be done in an open area free of obstacles
until the user is fully capable of driving safely.
The GAT444-IP should always be tested without any person sitting in the
wheelchair until every alteration of the physical installation or adjustment
is complete.
NOTI CE
Identifies important information not related to injury, but
possible property damage.
SAFE TY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.
CAUTION Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
WARNI NG Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
DANGER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.

vii
Parts and Accessories 7.0
Parts Included 7.1
8)
(2) (3)
(6)
The Gatlin Swivel Table Mount is pre-assembled before delivery. Included with
the swivel mount is:
 GAT444-IP Swivel Mount (1)
 SU275 17mm Ring (2)
 1/4”/20 x 3/4” Socket Head Screws (3)
 10-24 x 1/2” Socket Head Screws (4)
 8-32 x 1/2” Cross Head Screws (5)
 8-32 Nut (6)
(4)
(5)
(1)

1
Mounting 8.0
The GAT444-IP is a versatile hardware to
add virtually any tablet to a Gatlin armrest
positioning mount. With 360° rotating
capability and great compatibility, the
GAT444-IP is a great way to attach a tablet
to a seating system.
GAT444-IP Swivel Mount 8.2
Intended Use 8.1
The technical specs of this swivel mount include:
 Support tablet heights (long side) ranging from 7.3” to 10.75” and a maximum width
of 7.75”’
 Held in place by support cups on opposing ends of the cradle.
To Install:
 Pull out retracng spring loaded support cups
 Place tablet in between and allow support cup to retract over the tablet.
 The spring loaded support cup applies planar tension on the tablet, allowing for a sturdy
and stac posion while gently cradling the tablet.

2
Mounting 8.0
Hardware Mounting 8.3
Installation varies depending on which mounting hardware is used. Refer to list
below and follow corresponding instructions.
1. ARM240 Standard mount (1 & 3)
2. ARM250 Adjustable mount (1 & 6)
3. ARM250-I Fixed mount for Invacare armrests (1 & 6)
4. ARM240-I Adjustable mount for Invacare armrests (1 & 6)
5. ARM250-P Adjustable mount for Permobil armrests (2 & 6)
(9)
(11)
(10)
(8)
(6) (7)
(1) (2) (5)
(3) (4)

3
Mounting 8.0
Armrest Mounting 8.4
To mount an armrest with clamps:
1. Loosely thread screws through clamp plate (7) into base plate (8).
2. Posion armrests tube between clamp.
3. Tighten screws (6) with a 3/16” hex key unl the hardware rmly clamps onto the
armrest tube.
To mount an armrest with a Permobil track:
1. Lightly thread screws through the four holes on the hardware into track nuts (9).
2. Slide track nuts (9) into Permobil armrest track and ghten screws with a 1/8” hex key
unl the hardware rmly clamps on the armrest track.
To mount 3/4” stem rod with ARM240 hardware:
1. Slide rod into tube clamp.
2. Tighten the two socket head screws (10) with a 3/16” hex key unl the hardware rmly
clamps the rod.
To mount 3/4” stem rod with a ratchet handle (11):
1. Slide the rod into the tube clamp.
2. Tighten ratchet handle (11) unl the hardware rmly clamps the rod.
3. Permobil and Invacare specic hardware comes in 5/8” & 7/8” size rods.
NOTICE
To prevent electronics and sensitive devices from damage, keep area clear
when swinging rod away.

4
Positioning 9.0
Gatlin Positioning 9.1
Closed Open
GAT400-400-SWING
GAT400-8 POSITION GAT405-3 POSITION
The GAT400-400 does not lock into
place and has no set position, but
does allows for 180° swing away for
fast transfers. To prevent electronics
and sensitive devices from damage,
keep area clear when swinging
rod away
Hardware operation varies depending on which Gatlin is used.
GAT400–8 positions available
GAT405–3 positions available
To change the hardware position:
1. Pull and hold the top of the Gatlin barrel from the boom.
2. Move to desired posion.
3. Allow Gatlin barrel top to retract and lock into the new posion.

5
Adjustments 10.0
(2)
GAT444-IP Adjustment 10.1
The GAT444-IP swivel mount allows for highly versatile rotational adjustment.
For horizontal position and 360° rotational adjustment along the Gatlin arm:
1. Loosen the screw with a 3/16” hex key.
2. Posion hardware to the desired locaon and reghten the screw.
For 20° angle and 360° rotational adjustment at the ball mount:
1. Loosen the three screws on the mounng ring with a 5/32” hex key.
2. Posion hardware in desired locaon and reghten the screws.
(1)

6
Adjustments 10.0
Gatlin Adjustment 10.2
(3)
(4)
Vertical Adjustment:
1. Loosen screw (9) on Gatlin barrel with a 3/16” hex key.
2. Place height and rotaon to desired posion and reghten screws.
Fore and Aft Adjustment:
1. Loosen the two screws (5) holding the hardware rod (6).
2. Posion the hardware to the desired locaon and reghten.
Further Adjustment:
Adjustable mounng hardware allows for further vercal height adjustment.
1. Loosen screws (6) with a 3/16” hex key.
2. Posion the hardware to the desired locaon and reghten.
(5)

7
First Time Use 11.0
Dealer Assistance 11.1
During first time use by the client, it is advised that the dealer or service
technician assists and explains the configuration to the customer (the user
and/or the attendant). If needed, the dealer can make final adjustments.
User Testing 11.2
It is important that the customer is fully aware of the installation and how the
headrest can be adjusted in order to gain the best positioning possible. As a
dealer, proceed as follows:
 Explain and show the customer how you have executed the installaon, and explain
the funcon.
Have the user test the position of the GAT444-IP hardware:
 Is the hardware in the proper posion for the client?
 Can the user safely operate the chair?
 Is the placement of the GAT444-IP in an opmal posion for the user?
If needed, adjust the hardware to the proper position.
Explain to the customer any possible issues and how to address them.
Conditions of Use 11.3
The Gatlin Swivel Table is intended for use as installed by the dealer, in
accordance to the installation instructions in this manual:
 The foreseen condions of use are communicated by the dealer or service technician to
the user and/or aendant during the rst me use.
 If the condions of use change signicantly, please contact your dealer or a qualied
service technician to avoid excessive wear and tear or unintended damage.
WARNIN G
The Gatlin Swivel Table should only be prescribed and fitted by qualified health
care professionals.

8
Maintenance 12.0
Care and Maintenance 12.1
 Periodically check the hardware for loose screws or worn parts.
 To clean, use a general household cleaner.
 It may be required to ghten the set screw if the swing away mechanism is loose.
 If the hardware unintenonally swings away or does not lock into place when put in the
operang posion, the set screw will need to be loosened.
SAFE TY Replace or repair parts as needed.
DANGER
Failure to comply with these warnings could result in serious bodily harm.

a
NOTES 13.0

b
NOTES 13.0

c
NOTES 13.0

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P91D15 Revision Date 2019-12-17