Stealth Products SBM-DT User manual

SBM-DT
Owner's Manual for the
Dovetail Seat Back Mount
Head Support
Hardware
Parts Included
Part Description
A. Dovetail Track
B. Latch Body
C. Lever
D. Pivot Nut
E. Bushing
F. M5 x 0.8 x 22mm MOD FHS
G. M6 Socket Set Screw
H. M6 x 1.0 x 16mm FHS (2)
I. M6 x 1.0 Low Nylock Nut (2)
A
F
E
D
HI
G
C
B

1
Installation Instructions
Installing Dovetail Track to Seat Back
Securing Latch to Dovetail Track
1. Locate the mounting holes
on the seat back and align the
Dovetail Track (A) with them on
the back side of the seat.
2. Insert the M6 x 1.0 x 16mm
Flat Head Screws (H) through
the holes and thread the M6
Nylock Nuts (I) onto them.
3. With an open end wrench and 4mm
hex key, tighten the at head screws to
secure Dovetail Track (A) to the back.
1
2
3
1
3
2
1. Lift Lever (C) to expose the M6 Socket Set Screw (G). Make sure the set
screw is not protruding from the back of the Latch Body (B).
2. Slide the Latch Body (B) onto the Dovetail Track (A). The mount provides
6cm (2.375 in.) of lateral adjustment.
3. Once positioned, tighten the
M6 Socket Set Screw (G) with a
4mm hex key to secure.

+ -
2
Adjustment Instructions
Lateral Position Adjustment
Securing the Down Post*
* The SBM-DT is designed to t 1/2" down posts only. Not compatible with 15mm or other sizes.
Tension Adjustment
1. Release tension on the Lever (C)
and loosen the M6 Socket Set
Screw (G) located underneath the
Lever (C).
2. Move the mount and headrest left
or right on the Dovetail Track (A).
The mount provides 6 cm (2.375
in.) of travel.
3. Using a 4mm hex key, tighten the
M6 Socket Set Screw (G) and close
Lever (C) to secure the headrest in
position.
1. Open Lever (C) to release tension.
Insert the headrest down post into
the square slot in Latch Body (B).
Adjust the height of the headrest
according to the directions included
with your headrest hardware.
2. With the down post at the proper
height, close Lever (C) until it is
ush with Latch Body (B).
3. If the Lever (C) does not secure the
down post, or will not close ush
with Latch Body (B), refer to the
tension adjustment directions
below.
1. Open Lever (C) and locate the slotted
end of Adjustment Screw (F) as shown
in the image to the left.
2. To change the tension Lever (C) exerts
on the down post, use a small at
head screwdriver. Rotate the
Adjustment Screw (F) clockwise to
reduce tension and counter-clockwise
to increase.
3. Close Lever (C) to verify the tension on
the down post. Lever (C) should close
fully, hold the down post securely, and
provide resistance to unintentional
release.
6 cm (2.375 in)
1
3
2
1
2
3
1
2
3

Warranty
About Us
Stealth Products, LLC
[email protected]
www.stealthproducts.com
[phone] | [phone]
104 John Kelly Drive, Burnet TX 78611
MDSS GmbH
Schigraben 41
30175 Hannover, Germany
P143D659 SBM-DT Seat Back Mount Owners Jan 26, 2021
Stealth Products is committed to 100% customer satisfaction. Your complete
satisfaction is important to us. Please contact us with suggestions or feedback to
help us improve the quality and usability of our products.
You may reach us at:
Important
Before you install or begin using any product, it is important that you read and
understand the content of these installation and operating instructions. Product
misuse due to failure to adhere to instructions and warnings in this document will
void your warranty and may result in property damage, injury or death. Always
keep the operating instructions in a safe place so they may be referenced as
necessary. If this document contains information you do not understand or if there
are concerns about safety or operation, contact your provider.
All information, pictures, illustrations and specications are based on the product
information available at the time of printing, and are representative examples.
They are not intended to be exact descriptions of the various parts of the product.
Instructions are written with the expressed intent of use with standard
congurations. They also contain important safety and maintenance information.
For assistance with advanced congurations or options, contact your provider or
Stealth Products at [phone] or toll free at [phone].
Immediately discontinue use if any function is compromised, if parts are missing
or loose or if any component shows signs of excessive wear. Consult with your
provider for repair, adjustment or replacement. You can download additional
copies of this manual by visiting https://stlpro.site/stealth-docs/ and searching for
“SBM-DT” in the document manager.
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products will
repair or replace the product at our discretion. Any implied warranty, including the
implied warranties of merchantability and tness for a particular purpose, shall not
extend beyond the duration of this warranty. Stealth Products, LLC does not
warrant damage due to, but not limited to, misuse, abuse, or misapplication of
products and modication of product without written approval from Stealth
Products, LLC.
Any alteration or lack of serial number, where applicable, will automatically void
this warranty. Stealth Products, LLC is liable for replacement parts only. Stealth
Products, LLC is not liable for any incurred labor costs. No person is authorized to
alter, extend, or waive the warranties of Stealth Products, LLC.
To learn more about our warranty and returns policy, please visit https://stlpro.site/
returns-n-warranty.
© 2021, Stealth Products, LLC