Steeda 555-4032 User manual

2013+ Ford Focus ST and RS
Driver Side Engine/Transmission Mount
Instructions for parts #555-4032 and 555-4033
Removal of Factory Engine Mount:
1. The engine and transmission will need to be supported on the
transmission side before removing this mount. A jack should be
placed underneath the transmission, and raised just high enough to
keep the transmission and engine from moving very much when
the mount is removed.
2. Remove the engine cover by gently pulling up on the cover around
the corners.
3. Loosen the hose clamp securing the rubber intake tube to the hard
plastic intake tube. See figure 1.
4. Unplug the electrical connector for the MAP sensor. See figure 1.
5. Unclip the rubber strap securing the cold air feed tubes from their
mount at the cold air feed coming from the core support. See
figure 1.
6. Gently pull up on the air box and dislodge the rubber grommets
(beneath the air box) from their locating holes in the inner fender.
Gently pull the intake tube off of the plastic tube. Lift out the entire
assembly, with intake tube, and cold air feed tubes attached, in one
piece.
7. Remove the two rubber grommets from their respective studs on
the bottom of the air box. Insert the grommets back into their
respective holes where they were originally located.
8. Remove the top cover off of the battery tray, by pulling out and up
gently, on each side.
9. Unclip the wiring harness from the front of the battery tray, using a
flat head screwdriver, or by pulling out at each necessary location.
10. Disconnect the ground cable from the body, and then the positive
cable from the battery. Be sure to keep the terminals from
touching any metal surfaces.
11. Remove the battery hold down bracket.
12. Unplug the connector from the negative battery terminal.
1
Copyright: Steeda Autosports Inc. 555-4032/555-4033 3/19/2014
4
3
2
Hose Clamp
•A qualified technician should be used if you are not confident with replacing the factory driver side engine mount.
•A Ford service manual should be used in tandem with these instructions for further assistance and torque specifications.
MAP Sensor
Cold Air Feed Mount Strap
Remove
Battery Box Cover

13. Detach the front of the battery tray cover. The sides of the tray can be pushed
outward, while pulling up and out on the front of the box. Figure 5.
14. Remove the battery.
15. Remove the upper hose from the actuator of the sound symposer system.
Figure 6.
16. Unplug the sensor from sound symposer actuator. Figure 6.
17. Remove the three 10mm bolts securing the battery tray to its mount, and
remove the tray. Figure 7.
Before going on, be sure to have the engine and transmission
supported.
18. Remove the harness connector from the battery tray mount. Figure 8.
19. Remove the four nuts from the transmission mount, and remove the battery
tray mount. Figure 8.
20. Remove the main center bolt from the transmission mount, and remove the
mount. Figures 9 and 10.
21. Install the Steeda engine mount. Make sure both bushing washers are still
installed on both sides of the mount. Figure 11.
22. Install the provided 14mm bolt and washer into the transmission, and tighten
to OEM specs. NOTE: Apply a small amount of blue loctite onto the threads
of the 14mm bolt before installing. Figure 11.
23. Replace the batter tray mount. Figure 12.
24. Install the four nuts onto the transmission mount, and tighten to oem specs.
25. Reinstall the remaining components in reverse order of removal. Tighten all
fasteners to oem specs.
26. Make sure all harnesses are reconnected.
Copyright: Steeda Autosports Inc. 555-4032/ 555-4033 3/19/2014
7 8 9
6
5
Remove
10
11
12
Remove
Connector
Remove
nuts
Install
washer
underneath
bolt here.