Collex Communication BTC-01 User manual

Collex Communication Corp.
Proprietary and Confidential
1
Bluetooth Wireless Car Kit
Safety and General Information
Important information on safe and efficient operation Read this this
information before using your device.
Users are not permitted to make changes or modify the devices in any way.
Changes or modifications are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC Rules Operation is subjected to
the following two conditions.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.

Collex Communication Corp.
Proprietary and Confidential
2
Important. Please note the following:
This equipment has been tested and found to comply with the limits or a
Class B digital device, pursuant to part 12 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
residential radio frequency energy and if no installed and used in accordance
with instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measure:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
yConsult the dealer or an experienced radio/ TV technician for help.

Collex Communication Corp.
Proprietary and Confidential
3
Product care
yUse of non-original accessories may result in performance deterioration,
injury, products’ damage, electronic shock, and warranty termination.
yAttempt to disassemble your Car Kit may damage it ans the warranty
will be avoid.
yDo not put the Car Kit in a dusty place.
yUse only a clean soft cloth to clean your Car Kit.
yWhen the Car Kit is not in use, always keep it in its case.
yDo not allow children to play with your Car Kit, as they may injure
themselves and damage the Car Kit as well.
yDo not place the Car kit in an extremely hot or cold temperature, it the
Car Kit will not be used for a while.
Children
yDo not allow children to play with your Car kit, as the small parts may
cause a choking hazard.

Collex Communication Corp.
Proprietary and Confidential
4
zIntroduction
The BTC-01 are sophistically designed and engineered for safety so you can
focus on the road while your conversations are securely and invisibly
connected via Bluetooth technology. Hands-free answering and dialing are
available with your phone’s voice dialing/ answering capability. The powerful
speaker will allow you to hear your conversation even in noisy environments.
With the built-in charger connected to your car’s power outlet, your BTC-01
is automatically ready to use the moment you start your ignition. To enhance
the driving experience even further, this device is fully adjustable to allow
better control of the buttons.

Collex Communication Corp.
Proprietary and Confidential
5
zPackage
9BTC-01
9User manual
zBTC-01 Overview
1. Multifunction Button
2. Microphone Jack
3. Microphone
4. Lanyard Loop
5. Microphone Mute Button
6. Volume Button
7. Speaker
8. Nokia Charging Port
9. Mute & Status indicator
Led
Start To Use BTC-01
With the buit-in charger connected to your car’s power outlet, your BTC-01
is automatically ready to use the moment you ignition.

Collex Communication Corp.
Proprietary and Confidential
6
Turning the BTC-01 on and off
If you want to turn the BTC-01 on, please press the volume button, at the
same time, you hear a hint sounds “ti-ti-”. To turn the BTC-01 off, please
press and hold the volume button for 2~3 seconds till you hear 3 hint sounds
“ti-ti-ti-”.
Pairing your BTC-01 and phone
Before you can use your BTC-01, you must pair it with a device, for example,
a Bluetooth mobile phone. Mobile and BTC-01 can communicate as they are
turned on and within range of the phone up to 10 m (30 ft) outdoors or up to
5 m (15 ft) indoors with no solid objects in between.
1. Pairing with the BTC-01 and phone in close proximity.
2. When BTC-01 is on, press the volume button once to put it into pairing
mode. At the same time, you hear 4 hint sounds “ti-ti-ti-ti-” to inform you
are in pairing mode now and the BTC-01 indicator led illuminates. If you
want to cancel pairing, press volume button once.
Note. BTC-01 will automatically initiate a paired connection when powered on
and the last used device it was connected to. If you had paired with other
phone and you want to pair it with another one, please press volume
button once to disconnect the connection.
3. Switching mobile phone into pairing mode to discover BTC-01, for detail
on device discovery for your phone, refer to the user guide for the phone.
4. Select the BTC-01 from the discovered devices list and then confirm
following the on screen prompts.
5. Following the mobile user manual, entering the headset PIN code: 1234
Paired Link to additional Devices
BTC-01 can store pairing information for up to eight different devices
equipped with Bluetooth wireless technology. Devices are stored in a paired
Device list in memory in chronological order. When an attempt to pair to
more than eight devices is made, the oldest paired device is removed from
the list.
Any of the eight paired device can initiate a paired connection to the speaker.

Collex Communication Corp.
Proprietary and Confidential
7
If you want to connect the BTC-01 to another device in the paired device list,
you must initiate the connection from that device. Whichever of the eight
devices initiates a connection to the speaker afterwards then it becomes the
“last used” device.
Note: Some phones request authorization upon each connection, please press
volume button once to disconnect the previous connection.
Controlling BTC-01 Volume
During taking, you can adjust the volume from the buttons of headset.
To increase the volume•: Press the volume button in the up position
repeatedly until you reach the desired volume level, at the same time, you
hear a hint sound “ti”.
To decrease the volume•: Press the volume button in the down position
repeatedly until you reach the desired volume level, at the same time, you
hear a hint sound “ti”.
Answering and Rejecting Calls
When ringing, press the MFB button once to pick up the call. If you pick up
the call from mobile phone, you might need to chat by using mobile and you
can’t hear any voice from BTC-01 then you can press the MFB button once to
transfer the audio to BTC-01. For terminating a call, press the MFB button
once or the hang-up button of mobile phone.
Also, if you want to reject an incoming call, please press the volume button
once to reject it.
Note: Some phones do not support all features listed. Please consult your
phone user’s guide.
Using Voice Dialing
Please make sure the phone and the BTC-01 are on and within range of each
other. Press the MFB once. During this time, you might hear a beep tone in
the BTC-01. After the beep, voice dial as you normally would. In order to use
voice dialing, you must make sure your mobile phone supports this function.

Collex Communication Corp.
Proprietary and Confidential
8
Audio Transfer
During a call, you can press the volume button once to transfer the sound
between mobile phone and BTC-01. If BTC-01 is turned on after a call has
been initiated and the sound is on the mobile phone, you can transfer the
sound to BTC-01 by pressing the MFB button once.
Last Called Number Redial
BTC-01 enables you to do the last phone number redial. If you want to redial
the last called number, please press and hold the MFB button about 3~5
seconds.
Mute the BTC-01 microphone
BTC-01 enables you to mute the BTC-01 microphone during talking.
Therefore, if you want to have private discussion with others, just press the
mute button. Once the mute function is on, you will hear a repeated beep
tone to remind you that BTC-01 is in the mute mode. Disable the mute
function, press mute button once and then you can talk as you as you
normally would.
Other Functions
You can use call waiting function, please operate its function according the
following table.
Short Press MFB End the active call then answer second incoming call
Answer second incoming call and first call is placed
on hold
Long Press MFB
Swap between Two active calls
Reject second incoming callShort Press Power
End held call
Long Press Power During a call, add second call (3-ways call)
Note: Phone and service plan must support 3-way calling waiting to utilize the
functions associated with these features.

Collex Communication Corp.
Proprietary and Confidential
9
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by
the part responsible for compliance could void the user’s authority to
operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.

Collex Communication Corp.
Proprietary and Confidential
10
Notice: Any changes or modification not expressly approved by the party
responsible could void the user's authority to operate the device.