Steinberg UR-C V2.0 Instructions and recipes

EN
UR-C V2.0
Supplementary Manual

UR-C V2.0 Supplementary Manual 2
Contents
Plug-in
New functions of Guitar Amp Classics (common in
both DSP and Native versions)...........................3
Noise gate......................................................3
Cabinet simulations .......................................3
New features of Guitar Amp Classics (Native
version only)........................................................3
MONO / STEREO switching...........................3
Dedicated Windows for Cubase Series
Channel link setting added to the hardware input
setting field..........................................................4
UR-C series operations enabled in Mix Console
screen .................................................................4
dspMixFx UR-C
Addition of Firmware update function .................5
Improved usability (UR816C only) ......................6
• The DSP effect version works on the device.
• The plug-in version works as software on your computer.

UR-C V2.0 Supplementary Manual 3
Plug-in
New functions of Guitar Amp
Classics (common in both DSP
and Native versions)
Noise gate
A gate function has been added. By setting it
properly, you can remove unnecessary noise when
you are not playing.
Cabinet simulations
The function to select a simulated cabinet has been
added. This gives you expansion of the sound
creation range.
For the types and characteristics of cabinets that
can be selected, refer to the document Cabinet
types and characteristics in the Basic FX Suite
Operation Manual.
The function to select the position of the virtual
microphone for placement in front of the cabinet has
been added. There are two positions that can be
selected: Center and Edge.
New features of Guitar Amp
Classics (Native version only)
MONO / STEREO switching
When you insert Guitar Amp Classics into a stereo
channel, the MONO / STEREO switching function is
now displayed. In STEREO, the signal input with
stereo is processed by Guitar Amp Classics as it is.
In MONO, the stereo signal input is mixed into
monaural and then processed by Guitar Amp
Classics. The operation when you set MONO/
STEREO Selector switch to MONO is the same as
up to V1.5.
Noise Gate On/Off
Noise Gate Level
Cabinet type selection
Microphone position selection
Switching between mono/stereo

UR-C V2.0 Supplementary Manual 4
Dedicated Windows for Cubase Series
Channel link setting added to the hardware input setting field
You can now set channel links in the UR-C series hardware input settings area that appears in the project
window inspector.
Turns the channel links of two adjacent channels on (lit) or off (dark). When on, the two channels are linked and
function as one stereo channel.
UR-C series operations enabled in Mix Console screen
The UR-C series parameters in unit are now displayed in the [Hardware] rack ([MixConsole]  [Racks] 
[Hardware]). This allows you to work with the UR-C series while working with MixConsole without returning to
the inspector of the project window.

UR-C V2.0 Supplementary Manual 5
dspMixFx UR-C
Addition of Firmware update
function
You can now update the firmware of the UR-C main
unit from dspMixFx UR-C.
1. Connect the UR-C main unit with a firmware
version older than the firmware version in
dspMixFx UR-C installed on your computer.
The FIRMWARE UPDATER screen opens
automatically.
NOTE
You can cancel* the update by clicking the [CLOSE]
button.
2. Click the [START] button.
The firmware update will start.
3. After the update is complete, press the
[CLOSE] button to close the screen.
* If you cancel in step 1, you can always update the
firmware from [Firmware] on the setup screen.
Firmware

UR-C V2.0 Supplementary Manual 6
Improved usability (UR816C only)
When using the UR816C, the screen display of dspMixFx UR-C can now be scaled up or down to the left. This
provides improved usability.
Scaling up
or down
© 2022 Yamaha Corporation
Published 05/2022 MW-A0