Stellar Lighting MK-45 RGB User manual

www.stellarlighting.co.uk
1
MK-45 RGB fibre optic light engine
User manual
Features:
•45W light engine with RGB LED light
source
•29 mm port diameter
•RF remote
Technical specification
Light engine model
MK-45-RGB
Programmes
Brightness, speed, 5 programs, custom programs,
on/off
Remote controller
Yes, RF
Light source type
LED
CRI (Ra>):
80
IP rating
IP20
Light colour mode
RGB
Working voltage
DC12V
Rated power
45 W
Material of housing
Aluminium
Light engine dimensions
243 mm (L) x 150 mm (W) x 75 mm (H)
Light engine weight
1.9 kg
Remote control dimensions
85 mm x 52 mm x 7 mm
Fibre optic port diameter
30 mm
Fibre optic bundle compatibility:
B-29-XXX
Lifetime
50,000 hours
Warranty
2 years
Package dimensions (excluding fibre optic bundle)
290 mm (L) x 250 mm (W) x 130 mm (H)
Weight with packaging
2.5 kg

www.stellarlighting.co.uk
2
MK-45 RGB fibre optic light engine
User manual
Safety notices
Electrical work safety advice and tips
●Make sure the input voltage is correct.
●Avoid placing the light engine in the rain or in moist areas. Please ensure that the light engine has
sufficient ventilation and is not placed in a completely sealed area.
●Do not open the LED light engine for inspection or re-wire the electronic circuits if you are not a
professional. Opening the light engine might void your warranty.
●Avoid any debris on top or around the light engine as it can cause poor heat dissipation.
●Avoid using the device above 40 C temperature.
DIY tips and safety advice
●This task will involve working at height. A safe system of work should be established and maintained, in
order to prevent injury.
●Consider your safety! Think about the potential risks and dangers of the work and the steps you should
take to avoid them.
●Personal protective equipment. Make sure that you are equipped with suitable and sufficient personal
protectiveequipment.Thiscouldincludeeyeprotection,facemask,protectiveoveralls, safetyfootwear
and gloves.
●Ensure that the work area is sufficiently illuminated.
●Check that the tools you will be working with are in a good operating condition. For the installation,
you will need a cordless drill, epoxy glue, side cutters or scissors and drill bits.

www.stellarlighting.co.uk
3
MK-45 RGB fibre optic light engine
User manual
Connection method between optical fibres and the light engine
Your fibre optic bundle will come with the
connector fittings ready to connect to the
light engine. However, if you need to adjust
your bun
follow the steps below.
1. Align all the optical fibre ends and fasten with tapes which can resist temperature over 130℃
2. Pass the fibres through the connector and fasten the rotary tensioner until the fibres are tightened.
3. Cut the fibre bundle to a flat surface with a heat-knife or blade.
4. Make sure that the optical fibre bundle head is smooth and clean to ensure even light distribution.
5. he . Fasten the bundle with
the screw on the top of the .

www.stellarlighting.co.uk
6
MK-45 RGB fibre optic light engine
User manual
Pairing the remote controller
The remote controller is normally paired with the light engine, so you don’t have to do this when you
receive the light engine. However, in some cases the remote controller can unpair from the light engine.
In these scenarios, follow these steps:
Press the “FADE3” and “FADE7” buttons at the same time within the remote controller’s range. The light
engine will flash in white to indicate that the remote control is paired.
Troubleshooting for remote controller connection issues:
•Make sure that the remote controller is switched on by pressing the “On” button
•Check if the battery is operational in the remote controller: Press a button on the remote and
the indicator light should flash up. If the light doesn’t flash up, it means that there is either no
battery in the remote or the battery needs replacing.
•If the remote’s control light flashes up, check whether the green indicator light on the back of
the light engine flashes up, when a button is pressed on the remote. If the indicator light is not
flashing up, the remote controller might be unpaired from the light engine. To pair the devices,
press the “FADE3” and “FADE7” buttons at the same time within the remote controller’s range.
The light engine will flash in white to indicate that the remote control is paired.
•If the indicator light on the light engine still doesn’t flash up when pressing a button on the
remote controller, restart the device and test again.
•If you’re still experiencing issues, contact your supplier.
Table of contents