Steris RLM26HD3NPWR User manual

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
1 of 29
HD3 26″Monitor
LCD Surgical Grade Monitor
High Definition Wide Screen
OPERATION MANUAL
RLM26HD3NPWR HD3 26″Monitor with fiber input
RLM26HD3C HD3 26″Monitor with fiber input and power
supply
RLM26HD3MCNPWR HD3 26″Monitor with fiber input and integrated
microphone
RLM26HD3MC HD3 26″Monitor with fiber input, integrated microphone,
and power supply
RLM26HD3C

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
2 of 29
Notice for Users
FCC Statement
WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
For part numbers RLM26HD3C and RLM26HD3MC use only the included power supply, model
WSX624M, manufactured by Jerome Industries, to insure compliance with FCC regulations.
Declaration of Conformity
RLM26HD3C, RLM26HD3CNPWR, RLM26HD3MC, RLM26HD3MCNPWR:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device has been evaluated to the UL 60601-1 standard:
Equipment evaluated to this standard is not suitable for use in the presence of a flammable anesthetic
mixture with air or with oxygen or nitrous oxide (unless additional tests have been passed). Therefore
this device is not suitable for use in the presence of a flammable anesthetic mixture with air or with
oxygen or nitrous oxide.
Function, Intended Application and Mode of Operation:
HD3 monitors are intended to be used in the displaying and viewing of video and graphics for review and
analysis by trained medical practitioners. The mode of operation for this device is continuous operation.
These devices are classified as Class 1 Equipment:
RLM26HD3C, RLM26HD3CNPWR, RLM26HD3MC, RLM26HD3MCNPWR
Accessory Equipment:
Accessory equipment connected to the analog and digital interfaces must be certified to the respective
IEC standards (i.e. IEC 950 for data processing equipment and IEC 60601-1 for medical equipment).
Furthermore all configurations shall comply with the system standard IEC 60601-1-1. Any equipment
connected to the signal input part or signal output part configures a medical system. Therefore this
equipment, and new configuration, must comply with the requirements of the system standard IEC
60601-1-1.
For a complete list of current certifications, please refer to the Specifications page of this manual.
Part #:
Serial #:
IMPORTANT:
To aid in reporting in the case of loss or theft, or for
service maintenance purposes, please record the
monitor’s part number and serial number in the
space provided. The numbers are located on the
back of the monitor.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
3 of 29
UL Classified. See complete marking on product.
UL Classified part numbers:
RLM26HD3C
RLM26HD3CNPWR
RLM26HD3MC
RLM26HD3MCNPWR
The UL Classified part numbers RLM26HD3C and RLM26HD3MC include a power supply; model
WSX624M, manufactured by Jerome Industries Corporation.
The European Authorized Representative (AR) for this product on behalf of the manufacturer is:
Emergo Europe
Molenstraat 15
513 BH
The Hague, Netherlands
+31.70.345.8570 (Tel)
+31.70.346.7299 (Fax)
service
@
emer
g
o
g
rou
p
.com
The CE marking certifies that this product has met European Union consumer safety, health or
environmental requirements.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
4 of 29
Table of Contents
TIPS AND SAFETY PRECAUTIONS.............................................................................................................. 5
CONNECTING THE MONITOR AND TURNING ON/OFF.............................................................................. 6
Step 1: Unpacking the carton..................................................................................................................... 6
Step 2: Mounting the monitor ..................................................................................................................... 6
Step 3: Attaching the monitor to a boom arm and connecting video and power sources .......................... 6
USER INTERFACE.......................................................................................................................................... 8
User Interface Buttons................................................................................................................................. 8
Power Control.............................................................................................................................................. 8
Video Source............................................................................................................................................... 8
Keypad Lock................................................................................................................................................ 8
OSD Menu................................................................................................................................................... 8
OSD (ON SCREEN DISPLAY)...................................................................................................................... 10
OSD Navigation......................................................................................................................................... 10
Picture Menu ............................................................................................................................................. 11
Layout Menu.............................................................................................................................................. 13
Tune Menu ................................................................................................................................................ 16
COLOR CALIBRATION PROCEDURE......................................................................................................... 20
System Menu ............................................................................................................................................ 18
Default Settings......................................................................................................................................... 22
MONITOR CARE / TROUBLESHOOTING.................................................................................................... 23
SPECIFICATIONS......................................................................................................................................... 24
GLOSSARY................................................................................................................................................... 25
CABLE PIN OUTS......................................................................................................................................... 27
INDEX ............................................................................................................................................................ 28

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
5 of 29
Tips and Safety Precautions
- Image persistence on LCD monitors is caused
by the continuous display of static graphics on
the screen for extended periods of time. Do not
display a static image for more than eight (8)
hours. An afterimage may remain.
- To prevent image persistence,
power off the monitor when not in
use, especially at the end of the
day.
- It may be difficult to see the image if the
brightness is adjusted to the minimum setting.
- The quality of the video signal may influence the
quality of the displayed image.
- Do not open the monitor casing.
Monitor and Accessory Checklist
Part Numbers: RLM26HD3C,
RLM26HD3CNPWR, RLM26HD3MC, and
RLM26HD3MCNPWR
- Included in the carton are the following items:
1 HD3 Monitor
1 Cable Cover
(attached to the back of the monitor)
1 Power Supply* (RLM26HD3C and
RLM26HD3MC only)
1 Power Cord (RLM26HD3C and
RLM26HD3MC only)
8 Mounting Screws
(screwed into the back of the monitor)
1 Quick Start Guide
*Use only the Jerome Industries power supply,
model WSX624M included in the carton.
Notes:
- Retain the carton and packing material for
transporting the monitor.
Mounting
- Mounting the monitor to a boom arm requires
two people.
- Always follow mounting instructions to avoid
physical injury and/or damage to the monitor.
Location
- Use the monitor in a suitable environment. See
“Operating Temperature” and “Storage
Temperature” on the Specifications page of this
manual.
- Even though the monitor is classified as surgical
/ medical grade, use caution around liquids as
you would with any electrical appliance.
- Do not insert objects into the monitor.
- Do not place the monitor on unstable surfaces.
- In all cases, refer to the specifications in this
manual to ensure proper monitor performance.
Use of the monitor outside of operating
specifications will void the monitor warranty and
may cause permanent damage to the monitor.
- Note: This product contains fluorescent lamps;
please follow local ordinances or regulations for
disposal.
Power Cord
- Do not damage the power cord.
Damage to the cord may result in fire
or electric shock.
- Do not add extension cords.
- Use only the power cord and power supply
included with the monitor.
- Insert the power plug directly into the AC outlet.
- Do not remove or insert the power plug with wet
hands. Doing so could result in electric shock.
Manual Scope
- This manual is written for use with
RLM26HD3C, RLM26HD3CNPWR,
RLM26HD3MC, and RLM26HD3MCNPWR.
When describing a different specification /
function between the monitors, the part number,
is given. When the part number is not given, the
description is true for all monitors. For product
appearance, illustrations of part number
RLM26HD3C are used in this manual. The
integrated microphone in models
RLM26HD3MC and RLM26HD3MCNPWR is
operational only when the monitor is connected
to an integrated video system, sold separately.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
6 of 29
Connecting the Monitor and Turning On/Off
Step 1: Unpacking the carton
Unpack the monitor and other items from the carton. If any of the items are missing (see checklist on
previous page), please call Customer Support at [phone].
Step 2: Mounting the monitor
The back of the monitor (see Figure 1) has a hole pattern that complies to the VESA (Video Electronics
Standards Association) mounting standard. The monitor is shipped with eight screws that are screwed into
the back of the monitor. Four screws are 8-32 x 1/2" and four screws are 8-32 x 3/8". Remove all eight
screws and use one set of four screws to attach the monitor to the mount, either in the inside square hole
pattern (75mm) or the outside square hole pattern (100mm). Use the longer four screws for mounts with
thicker mounting plates. The mount is sold separately.
Note to users attaching the HD3 Monitor to an Operating Room Equipment Management System and/or
Equipment Boom:

If the HD3 Monitor is to be mounted on a boom and/or Equipment Management System, the boom
vendor should have wired the appropriate cables through the boom arm.
Step 3: Attaching the monitor to a boom arm and connecting video and power sources
1. Attaching the monitor to a boom arm requires two (2) people. One person supports the monitor and
aligns the mounting holes while a second person physically attaches the monitor to the VESA
mount attached to the boom arm.
2. After the monitor is mounted, remove the cable cover and connect the customer supplied video
cable(s) and power cord to the appropriate port on the back of the monitor. The ports on the
monitor are clearly labeled (see Figure 2).
3. The cable cover should be re-attached using the included screws.
4. The monitor will turn on automatically once it is connected to a power source.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
7 of 29







Figure 1: Rear view, shown with and without cable cover


Figure 2: Close-up of ports
VESA Mounting Holes, with Screws

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
8 of 29
User Interface
User Interface Buttons
The user interface is located on the front, lower right of the monitor. A drawing of the interface is shown
below in Figure 3.
Figure 3: User Interface
Power Control
The power is turned on and off by pressing the black POWER button. The blue indicator on the button will be
illuminated when the status is “On”. The monitor turns on automatically when connected to a power source.
Video Source
The video source is selected by pressing one of the eight blue buttons that corresponds to the connected
video source. A blue indicator will be illuminated on the button that is selected.
Keypad Lock
When keypad lock is active, all buttons on the interface are disabled. In this state, the user may only turn
the monitor on or off with the power button. A yellow indicator will be illuminated on the power button when
the keypad lock is active (“Locked”). Locking and unlocking the keypad is performed with Hot Keys, as
described below.
OSD Menu
Pressing the MENU /EXIT button on the user interface displays the first in a series of menus. To move to the
desired submenus that are available for each menu function, press either the , , or button. If in a
submenu, MENU /EXIT will return the previous menu. To exit the OSD menu select MENU /EXIT.
The monitor’s firmware version and release date is displayed at the bottom of each OSD menu.
Hot Keys / Direct Menu Access
Some menus can be accessed directly by pressing buttons on the interface. The following is a list of the hot
keys (single or combinations of interface buttons) and the menus that appear when pressed:
Backlight Brightness Increase
Press to increase the backlight brightness level.
Backlight Brightness Decrease
Press to decrease the backlight brightness level.
Contrast Increase
Press to increase the contrast level.
Contrast Decrease
Press to decrease the contrast level.
Note: To make adjustments to Backlight Brightness, Contrast and other menu functions relating to the look
and position of the image, the source must be connected, powered on and selected on the keypad.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
9 of 29
Lock Keypad
Press + to lock the keypad.
Unlock Keypad
Press +simultaneously to unlock the keypad.
Keypad Lock can be set to On (active) or OFF (inactive). The On position locks all the buttons on the
keypad. When Keypad Lock is active, pressing any of the buttons on the keypad will return a message on
the screen that reads “Keypad Locked”. When keypad lock is active the yellow LED on the black Power
button will be illuminated. When Keypad Lock is inactive, the message “Keypad Unlocked” appears on the
screen.
PIP (Picture-in-Picture) On/Off
Press + ENTER to turn PIP either On or Off.
Source Selection (Main source)
Press + ENTER to select the main source. There is an option to show All sources or Active sources. If
Active sources is selected, the Active sources (sources that are connected and powered on) are highlighted.
Source Selection (PIP source)
To select a PIP source, the PIP selection on the Layout menu must be set to ON. To select PIP ON, press
+ ENTER, or open the OSD menu and navigate to the Layout page). Press + ENTER simultaneously,
then press to select the PIP source. There is an option to show All sources or Active sources. If Active
sources is selected, the Active sources (sources that are connected and powered on) are highlighted.
The source selections are as follows, for both Main source and PIP1source:
Hi-Line Composite / Composite2
S-Video
YPbPr
VGA / RGB
3G- SDI
Fiber
Display Port
1The currently active Main source cannot be selected as the PIP source. The currently active Main source is
therefore excluded from the list of PIP source selections.
2To switch between Hi-Line Composite and Composite, press the Hi-Line Composite button on the keypad
twice.
Preset Configurations
To access the Preset Configurations menu, used for selecting User Presets and Fixed Presets and for
setting User Presets, hold the ENTER button down for two seconds. See p. 18 for more information on User
and Fixed Presets.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
10 of 29
OSD (On Screen Display)
OSD Navigation

Figure 4: OSD Menu Navigation Options
* Options indicated with an asterisk are available only with selected signals.
Picture TuneLayout System
Backlight Brightness
Contrast
Sharpness
Tint
Color Temperature
Language
OSD Setting
DVI Video Color Space
Noise Reduction
Picture Format
Freeze Frame
PIP
Custom Aspect Settings
Factory Reset
5500K
6500K
7500K
9300K
Phase*
Frequency*
Black Stretch
White Stretch
Transparency
OSD Timeout
OSD H Position
OSD V Position
YUV
RGB
Normal
Full Screen
Zoom In
5:4 Stretch*
On
Off
On
Off
H Offset
V Offset
Black Level Offset
OSD Navigation
Custom
Aspect
PIP Adjustments
PIP Size
H Position
V Position
EQ Enable
On
Off
Xray Enable
On
Off
Gamma
1.8
2.0
2.2
Serial Baud Rate
9600
19200
115200
Preset Configurations
Fixed Preset 1-3
User Preset 1-6
Color Saturation
Auto
7.5 IRE
Digital Brightness
H Position*
V Position*
Auto Adjust*
PIP Transparency
Side by side
Color
Red/Green/Blue Gain
Red/Green/Blue Offset
Zoom Level
Off
Low
High
Open Preset Menu
1.0
1.2
1.6
Analog RGB Calibration
YPbPr Calibration
Reset Calibration

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
11 of 29
Picture Menu
Figure 5: Picture Menu, Brightness – Sharpness Selections
Backlight Brightness - The backlight brightness setting increases or decreases the intensity of the backlight.
Backlight brightness can be accessed through the OSD menus, as shown above, or using the hot keys “”
and “”. When either of the hotkeys is pressed, the monitor displays the backlight brightness adjustment
menu.
Contrast - The contrast setting differentiates between variations of similar shades by adjusting the video gain
of the monitor. The contrast adjustment can be made for all inputs individually, so that when the input type
changes, the contrast adjustment will change with it. After adjustment, the new contrast value is displayed
on the screen until “Menu / Exit” is pressed or the OSD timeout period expires. Contrast can be accessed
through the OSD menus, as shown above, or with the hot keys “” or “”. When either of the hotkeys is
pressed, the monitor displays the contrast adjustment menu.
Phase - Applicable to Analog RGB and VGA signals only. Phase adjusts the internal clock to sample each
picture as near as possible to the center. The Phase setting does not have a fixed default value. It will
change depending upon different resolutions.
Frequency - Applicable to Analog RGB and VGA signals only. Frequency sets the total number of input
pixels per line to correspond with the input source. The frequency default is 100.
Sharpness - The sharpness setting digitally enhances the edges of an image. Sharpness is a low pass filter
that cuts off high frequency components not being introduced by image detail.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
12 of 29
Figure 6: Picture Menu, Color Saturation – Black Stretch Selections
Color Saturation - The color saturation setting will change the emphasis of the color component of the
image.
Tint - The tint setting adjusts the “shade” of the colors.
Color Temperature - A pre-configured color temperature can be selected. There are four available: 5500K,
6500K, 7500K and 9300K. The default is 6500K.
Black Level Offset - The monitor automatically detects whether the input device connected requires a black
level offset. The black level Offset control provides a manual override of the automatic setting. There are
two selections: Auto and 7.5 IRE. The default is Auto.
Black Stretch - The black stretch setting enhances dark colors in light images.
Figure 7: Picture Menu, Tint - White Stretch Selections
White Stretch - The white stretch setting enhances bright colors in dark images.
Digital Brightness - Adjusts the brightness level of each pixel. Adjusting this setting can result in a brighter
image than adjusting the backlight brightness.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
13 of 29
Layout Menu
Figure 8: Layout Menu, Picture Format – PIP settings
Picture Format - The picture format function selects the displayed aspect ratio when the signal input is at a
variance with the display panel’s natural/native aspect ratio. Not all settings give different results under
certain conditions. For example, when a 16:9 image is displayed on a 16:9 panel, any of the four setting
choices will result in an identical full screen image.
The format options are:
Normal – Preserves the aspect ratio of the incoming image and scales the image to fit the size of the
panel. Dependant on the aspect ratio of the panel, the image is either bordered on the right and left
sides or the bottom and top of the panel. Non-used areas of the panel are displayed black.
ZOOM IN – Magnifies the image, keeping the focus at the center. Adjust the amount of magnification
using the Zoom Level setting at the bottom of this menu. See Zoom Level on p. 15 for information on
using the setting.
Full Screen – Scales the image to the size of the panel without preserving the aspect ratio.
5:4 Stretch – Used with 1080i signals, centers a 5:4 aspect ratio image on the screen and stretches
the image to fill the screen without cropping.
Custom Aspect – A user defined aspect ratio will be saved under “Custom Aspect” when horizontal
and vertical offsets are changed in the Set Custom Aspect menu. Custom aspect remains saved
when inputs are changed. Custom aspect is saved until the monitor is powered off.
H Position - Applicable to RGB and VGA signals only. H Position adjusts the horizontal (left/right)
positioning of the image.
V Position - Applicable to RGB and VGA signals only. V Position adjusts the vertical (up/down) positioning
of the image.
Auto Adjust – Applicable to RGB and VGA signals only. Automatically centers the image on the screen.
Freeze Frame - When freeze frame is set to ON, the image will freeze (remain static) until it is set to Off or
until a different input source is selected. Freeze frame can be set to On or Off. The default is Off.
PIP - The PIP (Picture-in-Picture) menu selection enables and controls the PIP function. There are three
selections: Off, ON and Side by side.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
14 of 29
Off – A PIP window is not displayed.
On – A PIP image from a second channel (see PIP Source Selection below) is displayed in a
window within the main image. When PIP is set to ON, the following PIP Adjustments are enabled:
PIP Size - There are eight size selections (1-8) available for the PIP window. The default is
four.
H Position - The H position setting adjusts the horizontal (left/right) positioning of the PIP
window on the screen.
V Position - The V position setting adjusts the vertical (up/down) positioning of the PIP window
on the screen.
PIP Transparency- This function enables the PIP window to be set to varying levels of
transparency. The default is 0.
Side by side – Displays the main image and PIP window side by side and scaled to the vertical size
of the panel. The unused areas of the panel are displayed in black.
PIP Source Selection- Press “” and “Enter” simultaneously, then press “” to select the PIP source. PIP
has to be ON to select a PIP source (to turn PIP ON choose Layout then PIP in the OSD menus or use the
hot keys “” and “Enter”). There is an option to show All sources or Active sources. If Active sources is
selected, the Active sources (sources that are connected and powered on) will be highlighted.
Important Note on PIP: Please see PIP Matrix below for the signal types that can be used as the primary
and secondary input channel for PIP and Side by side.
Signal
(Connector)'#
$%
 
$ %

$#%
#
$
%
""
!
$#&(%

$#&(%
#
$%

"#

$%
'#
$%        
 
$ %        

$#%        
#
$%        
""!
!
$#&(%        

$#&(%        
#
$%        
"#

$%        
X = signals can be used as primary and secondary channels for PIP.
Table 1: PIP Matrix


Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
15 of 29
Figure 9: Layout Menu, Freeze Frame – Custom Aspect Settings
Custom Aspect Settings - A user defined aspect ratio will be saved under “Custom Aspect” in the Picture
Format menu when horizontal and vertical offsets are changed in this “Settings” menu. Custom Aspect
remains saved when inputs are changed and until the monitor is powered off. The range for both the
Horizontal Offset and Vertical Offset is negative 100 to positive 100 in increments of five. The default is 0.
Color - Red, Green & Blue Gain- Increasing the gain of a color multiplies the proportion of that color by a
factor. Red, Green and Blue can be adjusted separately. Red Gain, Green Gain and Blue Gain all
have a default of 50.
Red, Green & Blue Offset- Increasing the offset of a color increases the proportion of that color in
the background of the image. Red, Green and Blue can be adjusted separately. Red Offset, Green
Offset and Blue Offset all have a default of 50.
Figure 10: Layout Menu, Color Settings
Zoom Level - Adjust the amount that the image is magnified. Image is magnified from the center. This
setting can go up to 45.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
16 of 29
Tune Menu
Figure 11: Tune Menu
Language - English (American) is the only selection.
Figure 12: OSD Settings
OSD Setting - These settings control the appearance of the OSD.
Transparency - The transparency setting enables the OSD to be set to varying levels of
transparency. The default is 50.
OSD Time-out - The OSD time-out setting enables the user to control the time that the OSD menu
displays. The OSD time-out can be set from 1 to 60 seconds. The default is 20 seconds.
OSD H Position - Controls the horizontal (left/right) positioning of the OSD menu on the screen.
OSD V Position - Controls the vertical (up/down) positioning of the OSD menu on the screen.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
17 of 29
RGB HD Video Color Space - Applicable to RGB signals only. There are two options available for this
setting. YUV is used for video timing and RGB is used for VESA/PC timing. RGB is the default.
Figure 13: Tune Menu, DVI Video Color Space Setting
DVI Video Color Space - Applicable to DVI signals only. There are two options available for this setting. YUV
is used for video timing and RGB is used for VESA/PC timing. RGB is the default.
Noise Reduction - Applicable to Analog RGB and VGA signals only, the noise reduction function utilizes a
per-pixel motion adaptive algorithm to remove noise (distortion) from the image while leaving the image’s
content, motion and detail intact. It also blocks artifacts. Noise Reduction can be set to Off, Low or High.
The default is Off.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
18 of 29
System Menu
Figure 14: System Menu
Analog RGB Calibration - Applicable to RGB signals only.Calibrates the color response of the RGB input to
match the standard color space. This function is for service personnel only.
YPbPr Calibration - Applicable to YPbPr signals only. Calibrates the color response of the YPbPr input to
match the standard color space. This function is for service personnel only.
Reset Calibration - Applicable to RGB and YPbPr signals only. Sets the calibration of Analog RGB or YPbPr
signals to the factory defaults. When Reset Calibration is selected, the message “Press Enter To Confirm”
will appear. Press Enter to confirm calibration reset.
Factory Reset - Resets all settings to the factory defaults. When Factory Reset is selected, the message
“Press Enter To Confirm” will appear. Press Enter to confirm reset. Factory defaults are listed on page 14.
Open Preset Menu – Opens the preset menu, shown below.
Figure 15: Preset Configurations Menu
•To select a User or Fixed Preset, use the and arrow keys to navigate the presets. The monitor
previews with the preset values as the selections are made. To select a preset, press ENTER. The
preset is applied to the monitor and the Preset Configurations menu closes. To keep the monitor
settings that were applied prior to opening the Preset menu, navigate back to the Current Settings
item at the top of the menu before the menu times out. The original settings are reapplied.
•To save the current settings as a User Preset, press . The Fixed Presets gray out and are no
longer selectable. Use the and arrows to select the User Preset to store the current settings,
then press ENTER to save the setting. The menu closes.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
19 of 29
EQ Enable - Applicable to DVI signals only, EQ Enable can be set to On or Off. The default is Off. This
option, when ON works as an equalizer to reduce distortion, typically sparkles and vertical lines on the
image.
Xray Enable - Xray Enable can be set to On or Off. The default is Off. When On, the backlight of the panel
is set to maximum brightness for viewing films.
Gamma - A pre-configured gamma curve can be selected. There are six available: 1.0, 1.2, 1.6, 1.8, 2.0
and 2.2. The default is 1.6.
Serial Baud Rate - The serial baud rate is the rate at which information is transferred. It is measured in bits
per second. There are three selections: 9600, 19200 or 115200. The default is 9600.

Document #OPM/1300, Revision B CONFIDENTIAL © 2013 Copyright VTS Medical Systems, LLC
20 of 29
Color Calibration Procedure
Monitors are factory color calibrated. However, RGB, VGA, and YPbPr signal colors may be affected by
signal loss over field wiring. If the colors for these signals need adjustment, a field technician can perform
the calibration procedure below.
Equipment required:
•Sencore Video Pro Multimedia Generator (or equivalent)
•DVI to VGA adapter
VGA/RGB Calibration
1. Connect the video generator to the monitor’s VGA/RGB input.
2. On the video generator, make the following selections. Proper settings are required for the
calibration to be saved.
•Signal type: VESA/Mac-RGB
•Format: 1024x768_60Hz
•Pattern: Staircase with 16 bars, as shown below

Figure 16: Staircase Test Pattern
3. On the monitor, press MENU to open the OSD menu.
4. Navigate to the System menu and select Analog RGB Calibration.
The monitor calibrates.
5. Before cycling power to the monitor, note how the pattern looks with calibration. In the next step
you will compare the image as it looks now (immediately following calibration) to how it looks after
power is cycled.
6. Reset power to the monitor and verify that the calibration saved. If the calibration saved, the image
looks exactly as it did after the calibration was completed.