Sterling Plumbing 71100116 User manual

Features
•Compression molded from our exclusive solid Vikrell
®
material
•Tongue-and-groove 4-piece modular design allows for
easy ″snap together″installation
•Gentle sloping back, neck, and armrest in bath
design
•Bath and integral apron eliminates installation step
•Durable high-gloss finish
•10-year consumer/3-year commercial limited warranty
•Available with above-the-floor drain
•Wall surround allows for attachment of grab bars
•60-1/4″(1530 mm) x 37-1/2″(953 mm) x 73-1/4″
(1861 mm) complete unit rough-in dimensions
•60″(1524 mm) x 36″(914 mm) x 72″(1829 mm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ASTM E162
•ASTM E662
•CSA B45.5/IAPMO Z124
36″(914 mm) OVAL BATH/SHOWER
SYSTEM WITH BACKER BOARDS
71100116
ALSO 71100118, 71100126, 71100128
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71100116 36″(914 mm) oval bath/shower system and wall surround with backer boards, left
drain ❑0❑Other____
71100118 36″(914 mm) oval bath/shower system and wall surround with backer boards,
above-the-floor left drain ❑0❑Other____
71100126 36″(914 mm) oval bath/shower system and wall surround with backer boards, right
drain (shown) ❑0❑Other____
71100128 36″(914 mm) oval bath/shower system and wall surround with backer boards,
above-the-floor right drain ❑0❑Other____
Model Wall Component Description Colors/Finishes
71104106 Complete wall set with backer boards ❑0❑Other____
ENSEMBLETM
Page 1 of 2
1065810-4-F
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING

Technical Information
Fixture*:
Basin area:
Bathing well, bottom 40″(1016 mm) x 21″(533 mm)
Bathing well, top 52″(1321 mm) x 29″(737 mm)
To overflow:
Water depth 11″(279 mm)
Capacity 40 gal (151.4 L)
* Approximate measurements for comparison only.
Model Door width Door maximum
height
71100116
71100118
71100126
71100128
58-1/2″
(1486 mm)
55-3/4″
(1416 mm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown.
Attach grab bars at the specified backer board locations only.
3/4"
(19 mm)
Note: Right and left end walls
are the same, only mirrored.
24" (610 mm) Grab Bar
10" (254 mm)
Back Wall End Wall
3/4"
(19 mm)
1" (25 mm) 1" (25 mm)
3-1/2" (89 mm)
1" (25 mm) Backer Board Locations
Overflow Detail
2-7/8" (73 mm)
3-1/2"
(89 mm)
30" (762 mm)
1-1/4"
(32 mm)
37-1/2"
(953 mm)
24-1/2"
(622 mm)
4"
(102 mm)
8"
(203 mm)
16"
(406 mm)
73-1/4"
(1861 mm) 3"
(76 mm)
60"
(1524 mm) 1-1/2"
(38 mm)
19"
(483 mm)
20"
(508 mm)
36" (914 mm)
16"
(406 mm)
14"
(356 mm)
6" (152 mm)
(Typical)
37-1/2"
(953 mm) Drain Cutout
Ø 2"
(51 mm)
Drain
8-3/4"
(222 mm)
60" (1524 mm) Min
60-1/8" (1527 mm) Max
17-1/4"
(514 mm)
11-1/2"
(292 mm)
14"
(356 mm)
53"
(1346 mm)
18" (457 mm) Grab Bar
2" (51 mm)
Product Diagram
ENSEMBLETM
ENSEMBLETM 36″(914 mm) OVAL BATH/SHOWER SYSTEM WITH BACKER BOARDS
Page2of2
1065810-4-F