Sterling Plumbing Oval Bath/Shower System with Backer Boards... User manual

Features
•Compression molded from our exclusive solid Vikrell
®
material
•Tongue-and-groove 4-piece modular design allows for
easy ″snap together″installation
•Gentle sloping back, neck, and armrest in bath
design
•Bath and integral apron eliminates installation step
•Durable high-gloss finish
•10-year consumer/3-year commercial limited warranty
•Available with above-the-floor drain
•Wall surround allows for attachment of grab bars
•60-1/4″(1530 mm) x 43-1/2″(1105 mm) x 73-1/4″
(1861 mm) complete unit rough-in dimensions include
flange
•60″(1524 mm) x 42″(1067 mm) x 72″(1829 mm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ANSI Z124.1.2
•ASTM E162
•ASTM E662
•CSA B45
42″(1067 mm) OVAL BATH/SHOWER
SYSTEM WITH BACKER BOARDS
71110116
ALSO 71110118, 71110126, 71110128
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Colors/Finishes
71110116 42″(1067 mm) oval bath and wall surround with backer boards, left drain ❑0❑Other_____
71110118 42″(1067 mm) oval bath and wall surround with backer boards,
above-the-floor left drain
❑0❑Other_____
71110126 42″(1067 mm) oval bath and wall surround with backer boards, right drain (shown) ❑0❑Other_____
71110128 42″(1067 mm) oval bath and wall surround with backer boards,
above-the-floor right drain
❑0❑Other_____
Model Component Description Colors/Finishes
71114106 Complete wall set with backer boards ❑0❑Other_____
ENSEMBLETM
Page 1 of 2
1065809-4-F
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING

Technical Information
Fixture*:
Basin area:
Bathing well, bottom 40″(1016 mm) x 27″(686 mm)
Bathing well, top 52″(1321 mm) x 35″(889 mm)
To overflow:
Water depth 11″(279 mm)
Capacity 45 gal (170.3 L)
* Approximate measurements for comparison only.
Model Door width Door maximum
height
71110116
71110118
71110126
71110128
58-1/2″(1486 mm) 55-3/4″(1416 mm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown.
Attach grab bars at the specified backer board locations only.
3/4"
(19 mm)
Note: Right and left end walls
are the same, only mirrored.
24" (610 mm)
Grab Bar
10" (254 mm)
10" (254 mm)
Back Wall End Wall
18" (305 mm)
or 24"
(610 mm)
Grab Bar
3/4" (19 mm)
1" (25 mm)
1" (25 mm)
3-1/2" (89 mm)
1" (25 mm) Backer Board Locations
Overflow Detail
2-7/8" (73 mm)
3-1/2"
(89 mm)
30" (762 mm)
1-1/4"
(32 mm)
43-1/2"
(1105 mm)
27-1/2"
(699 mm)
4"
(102 mm)
8"
(203 mm)
16"
(406 mm)
73-1/4"
(1861 mm) 3"
(76 mm)
60"
(1524 mm) 1-1/2"
(38 mm)
19"
(483 mm)
20"
(508 mm)
42" (1067 mm)
16"
(406 mm)
14"
(356 mm)
6" (152 mm)
(Typical)
43-1/2"
(1105 mm) Drain Cutout
Ø 2"
(51 mm)
Drain
8-3/4" (222 mm)
60" (1524 mm) Min
60-1/8" (1527 mm) Max
20-1/4"
(514 mm)
11-1/2"
(292 mm)
14"
(356 mm)
53"
(1346 mm)
Product Diagram
ENSEMBLETM
ENSEMBLETM 42″(1067 mm) OVAL BATH/SHOWER SYSTEM WITH BACKER BOARDS
Page2of2
1065809-4-F